Creation of Multiple viewports, Scaling the drawing and setting in Template in AutoCad

1. STRCTURE 1 For this structure is considered as it is asymmetric in nature. Here cannot to be considered as a horizontal irregularities and the shear wall shape like L. There is some uncertainty concerning certain features of the seismic response of non-rectangular walls. It occurs lack of tensile capacity and force…

1. SYMMETRY: Having a look over the aspects of symmetry of the framing plan, it is observed that the distribution of mass,Stiffness is across the plan;it is observed that the distribution of mass, stiffness is across the plan.It is considered for one of the good Symmetrical aspects.This tends to reduce the horizontal displacements…

Ans:                                                                                          …

1.  Static Analysis: Static analysis of structures considers static loads acting on the structure such as dead,live load which does not vary with time and are not considered to be sudden. In static analysis stiffness matrix alone is considered and the inertial forces are not considered.Motion of the structure…

Question 1: What is the mode of failure or damage of the beams in the figure above? Are the damages repairable? Elaborate a)  Answer 1(a) Observation: In this picture we observe that, concrete get damage/ broken and reinforcement are visible at the bottom of beam. The concrete spalled beyond the reinforcement that…

AIM:  To create a 3D rendered model for a Residential Building in AutoCAD INTRODUCTION: The main objective of this project is to understand about to create a Plan in 2D, then convert it into 3D using AutoCAD 3D, applying materials and rendering. AutoCAD is primarily used for generating 2D sketches. While it is…

1.  Aim : Template, inserting text and attributes Doors of warehouse and placing it in blocks Electrical legend and making it blocks Different types of door for residential project Drawing bars, making it as block and making it as a table as bar bending schedule. Procedure : Custom 1_ title block: Create a rectangle…

1. Create a 3D Isometric View of the building with plan and elevation given.     Aim : To create a 3D isometric view of the given building with plan and elevation.      Procedure :     Step 1 :   First we have to open the autocad and the set the maximum limit and minimum…

1.AIM To create a 3d furniture elements using the various commands in the autocad. Introduction by 3d view  the process of creatting a mathematical representation of any surface of an object in three dimensions by using special software a 3d model can even be represented as atwo dimensional image by using the 3d rendering…

AIM: To create a layout of the plan and section A of the propject in the challenge 7 procedure: in the command prompt type units>mm>decimal in the command prompt type limax>100,100 in the command prompt type limits>0,0 in the command prmpt type layout >template>tutorial arch.m in the command prompt type…

AIM: To create the kitchen layout and to also,use proper dimension techniques to dimension the kitchen layout.also insert text wherever required. all dimensions are in mm. procedure: step1: units are set to mm limits and limax are also set zoom comand is also used.  steps for drawing below counter plan open autocad…

AIM: TO CREATE TEMPLATE,INSERTING TEXT AND ATTRIBUTES DOORS OF WAREHOUSE AND PLACING IT IN BLOCKS ELECTRICAL LEGEND AND MAKING IT BLOCKS DIFFREENT TYPES OF DOORS FOR RESIDENTIAL PROJECT DRAWING BARS,MAKING IT AS BLOCK AND MAKING IT AS A TABLE AS BAR BENDING SCHEDULE. COMMANDS USED: BLOCK INSERT ATTRIBUTES FIELD RECTANGLE…

1.AIM: TO PRODUCE DRAWING OF THE HOUSES WITH PLAN,ELEVATION,AND SECTION PROCEDURE: USING AUTOCAD TOOLS AND FUNCTIONS                                                          …

   Aim: To sketch a g+1 floor residential plan according to vastu shastra and lsit down the names of the structural drawings. vastu shastra is the ancient indian science of architecture and acts as a guideline to design your home in the way that enhances positice energy our nature is abundant with powerhouse…

AIM: To calculate the concrete mix design for m35 grade concrete with fly ash and m50 grade concrete without flyash.   INTRODUCTION: Concrete mix design is the method of finding accurate proportion of cemnet,sand,and aggregates for concrete to achieve target strength in structures. so concrete mix design can…