Creating Bar Bending schedule, Different Door types, and Creation of standard drawing templates using AutoCad

1. Design a Warehouse Building located in Chennai using STAAD Pro Connect Edition.   Aim and Introduction:                     To model and design a warehouse building which was located in chennai   Procedure:  

Question 1: a. What is the mode of failure or damage of the beams in the figure above? Are the damages repairable? Elaborate                                     Crack is formed due to flexural failure in beams. Shear failure happens when the applied shear stress on a beam exceeds the shear strength of the material, leading…

   1. Design a multi-storey Residential Building located in Bangalore using STAAD Pro Connect Edition. The specification must          be as follows: Building Floor-G+6+R Plan dimension- B=25,L=16 Storey Height=3.5m Soil=Hard Soil Use=Residential Perpose Safe Bearing Capacity=180kN/m2…

     QUE.-1.1       1. State the primary load cases to be considered for design.     Ans:- The primary load cases that are to be considered for design are listed below: Dead Load (IS 875: Part I). Live Load (IS 875: Part II). Wind Load (IS 875: Part III). Snow Load…

    QUE:-1.1     QUE.-1. How will you assign Circular section to column?     ANS:  Go to properties in that select define property select circle and give the radius for the member and assign the defined circle to the member created.            …

    Que.1     1. 1. Write the steps involved to upload a .std file through web mail?     Ans- Steps involved to upload a .std file through web mails are as follows; Open the STAAD pro software and Choose share option. After clicking on the share button, select send mail option.  …

   1. ANS-    Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve.    AIM:-Need to create sinusoidal point then curve from the point and then create surface.    INTRODUCTION:-By using dynamo created a sinusoidal point then created…

   1. Aim: To export the Revit architectural and structural to Navisworks manage.     Procedure: Open the Revit software. Click on open and select week 7 Architectural and structural plan. Click on File and select export to NWC.             2. Aim: Use Navigate…

   1 Ans- My project is to build a Multi-Unit Residential Apartment.    2 Ans- Assume reasonable assumptions for geographic and location details for your project modeling are                        follow, The construction location is…

    1. Aim: To model a ceiling above the architecture plan.     Procedure: Open Revit software. Open the project you created. Select the ceiling from the architecture toolbar.       Click on Sketch Ceiling.       Click on Pick line.       Now select each…

                   Aim: To create a 3D model of a residential building with a rendered view.       The dimensions: External and Internal wall – 0.220m and 0.110m thick W -1.80 X 1.20 W1- 1.50 X 1.20 V -0.60 X 0.75 M.D-1.00 X 2.20 D1-0.90 X 2.20 D2 -0.75…

      1. Aim: To create a 3D isometric view of the building with plan and elevation using autocad.       PROCEDURE:    In the command box type units and click on engineering-0'-0" In the command box type limits-0'0" In the command box type zoom-a Go to the top view In the command…

      1.Aim: To Create 3D furniture elements using AutoCAD software.       Procedure: Open AutoCAD and click 3D modelling. In the command box type units-engineering-inches-0'-0" In the command box type limits-0'-0' In the command box type zoom In the command box type box and give the dimensions…

       1.Aim: To create a layout of the plan and section A.  PROCEDURE- In the command box type layout-template-tutorial arch.m In the command box type ms to specify the center of plot  To click on the tittle box to edit the tittle. In the command box type mv and add the view. In the command…

PROBLEM 1  Aim :- To create the kitchen layout and to provide the hatch. Introduction :-     The general commands used for drawing the building is as follows : Line Polygon Rectangle Circle Erase Copy Trim Mirror Offset Extend Array Move Rotate Dimension Text Fillet RESULT-    PROBLEM 2 Aim :- To create the elevation of…

Creating Bar Bending schedule, Different Door types, and Creation of standard drawing templates using AutoCad.  Problem-1,2,3 Aim :- To create the templates and save the templates as a block. Introduction :-     The general commands used for drawing the building is as follows : Line Polygon Rectangle Circle…

      Project : - Creating an Architectural plan for the provided plot size and develop relevant basic structural drawings Aim :- To draw the Residential Building in the plot size of 60’ X 20’ ( 18.3m X 6m ) facing East direction with the following drawings : Architectural Drawing Site…

Vastu shastra is the ancient indian science of architecture and acts as a guideline to design your home in the way that enhances positive energy. Our nature is abundant with powerhouses of energy sources like the sun, wind, moon, water, earth and fire.  Effects of sunrays, flow of winds, pull of earth’s magnetic…

Calculate the concrete mix design for M35 grade concrete with fly ash         Given,         M35 grade concrete with fly ash Mix Design: a) Target Mean strength:          Grade of concrete = M35          fck = 35 N/mm2    …