Creating an Architectural plan for the provided plot size and develop relevant basic structural drawings

    Project 1 : Comparative study of different storey buildings for Seismic forces   Aim :- To model and analyse the building  from A to K with the given structural data and compare the analysis between the models based on the different factors.   Introduction :- Every building has a…

  Modelling of 25 storey building with the specified properties using ETABS Question :  Model a 25 storey building on ETABS with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey height…

  Conceptual design of a building with columns and shear walls   Question 1:The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional…

  Concept on positioning of Columns

  Understanding the concepts on Degrees of Freedom   Question 1: A five storey structure with 5 translational DOF is shown here. Each storey has mass ‘m’. The eigenvalue problem has been solved and the 5 periods of vibration Tn and their corresponding mode shapes, φn has been derived.…

Calculation of Stiffness in Structural elements     Question 1: Compute lateral stiffness of the one story frame with an intermediate realistic stiffness of the beam. The system has 3 DOFs as shown. Assume L = 2h and Elb = Elc   Answer :-   Question 2: For the following structures: a) Determine…

     Identification of Cracks    Question 1 What is the mode of failure or damage of the beams in the figure above? Are the damages repairable? Elaborate    a) The mode of failure is flexural cracks developed at the bottom flange of the beam  Here we can see that, the…

  Revit Project 4 : Usage of Navigation tool , Timeliner and Clash Detection test using Naviswork    1) Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings…

    REVIT Project 3 : Creating Conceptual mass in REVIT and Creation of Sinusoidal curve and a Parametric stadium using Dynamo   PROBLEM 1 Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve   Answer :- Aim :- To use the Dynamo,create a set of sinusoidal…

  Preparing Schedule & Cost Estimation for a building using REVIT     1) Use the shortcut keys in Revit discussed in class to complete the following tasks and list them below            a. Using 3D model create a section box          …

  Structural analysis of a buidling using Robot Structural Analysis   1) What are HVAC systems? Why are they essential in the modeling of buildingsAnswer :- The HVAC stands for Heating, Ventilation, and Air Conditioning. HVAC refers to the different systems used for moving air between indoor and outdoor areas,…

  Project 2 : Creating Architectural and Structural model with 3D rendering using REVIT     Problem 1 Select the type of structure you want to build from one of the three below:         a. Multi-Unit Residential Apartment         b. Office Buildings  …

   Usage of Collaborate tool in REVIT   1) Open an architectural template. Using the Manage tab set project base point and project shared coordinates for the project   Aim :- To set project base point and project shared coordinates for the project   Procedure :- Step 1 Click on windows start In…

  Introduction to National Building Code and Steps in a Construction project    1) Why are building codes or standards essential for the modeling/  efficiency of drawings in Revit ?  Answer :-A building code, or building control, is a set of rules that specify the minimum standards for…

REVIT Project 1 :     3D Creation of Celing, Roof, Architectural plan,                Structural plan, Sectional view, Elevation view and          Camera specific view for a house plan using REVIT   PROBLEM 1 Based on the project saved from…

       Creating Walls, Partition walls and Floors for                  a residential layout using REVIT    PROBLEM 1 Aim :- To provide the flooring with appropriate material and thickness in the residential unit (created in Week 2 )   Procedure…

    Creating Levels, Grids, Layout and model        elements for a residential unit using REVIT   Problem 1 Aim :- To know What is BIM and to Summarize the features of BIM and benefits of using BIM over 2D CAD tools    BIM BIM is an acronym for Building Information Modeling…

    Introduction to REVIT concepts     Problem 1 Aim :- From the file menu, to create a new project ( Structural / Architectural / Constructional Template ) and to name the project   Procedure :- Step 1 Click on windows start In Search bar type > Revit Click > Revit 2021 Once the revit is open, It will shows the following…

   PROJECT 2 : Creating a 3D rendered model for a Residential Building in AutoCad   Aim :- To draw the 3D residential building and to create the rendered view   Introduction :- The general commands used for drawing the building is as follows : Line Polygon Rectangle Circle Erase Copy Trim Offset Extend…

   Creating 3D Isometric view of various            structural elements in AutoCAD     PROBLEM 1   Aim :- To Create a 3D Isometric View of the building with plan and elevation given   Procedure :-   Click on AutoCAD application and open this application Type…

    Creating various 3D Models like Furniture, Footing,    Girder, Column drop with panel and Gable Wall in      AutoCad   PROBLEM 1   Aim :- To Create a 3D Furniture element as shown in the Figure   Procedure :- Click on AutoCAD application and open this application Type…

     Creation of Multiple viewports, Scaling the              drawing and setting in Template in AutoCad   PROBLEM 1 Aim :- Create a layout of the Plan and Section A of the project in Challenges 7, using the template Tutorial mArch.dwt in a scale as given in the Figure.…

       Creating Kitchen layout, Hatching of                       Architectural elements and sectional view of           an Industrial Building in AutoCad       PROBLEM 1    Aim :- To create…

  Creating Bar Bending schedule, Different Door types, and Creation of standard drawing templates using AutoCad     PROBLEM 1   Aim :- To create the templates and save the templates as a block.   Introduction :- The general commands used for drawing the building is as follows : Line Polygon Rectangle…

          Project : - Creating an Architectural plan for the provided plot size and develop relevant basic structural drawings     Aim :- To draw the Residential Building in the plot size of 60’ X 20’ ( 18.3m X 6m ) facing East direction with the following drawings :  …

      Creating a Layout, Section and Elevation with dimensions using AutoCad       Aim :- To draw the Plan, Elevation and Section of the building by using AutoCAD Software         Introduction :- The general commands used for drawing the building is as follows : Line Polygon…

    Creating a Wardrobe detailed drawing, Floor Plan, Kitchen Layout and Column Detail using AutoCad         1. Elevation and Details of Wardrobe Aim :- To Draw the elevation and details of a wardrobe as shown in the below fig by using AutoCAD Software Procedure :-   Click on AutoCAD…

           Creation of Column Schedule and Drawing Template using AutoCad             Column Schedule   Aim : To Create a Column Schedule as shown in below fig by using AutoCAD Software   Procedure :-   Step : 1 – To Draw the Table Click on…

      Creating a Residence Layout, Seating plan, Toilet and Utility room plan using AutoCad     1. Aim : To draw the layout of the residence plan as shown below       Introduction :   The above fig is nothing but the residential plan consisting of following units Two Bedrooms…

        Drafting of various geometries using Chamfer, Fillet tool in AutoCad   Aim :- To draft the following geometory by setting the unit of measurement as decimal in AutoCAD Software     Procedure :-   Click on AutoCAD application and open this application Type QNEW in command…

      Creating a Floor plan, Footing detail and Isometric view using AutoCad       C.S. of load bearing wall over spread footing :   Aim : - To draw c.s. of load bearing wall over spread footing   Procedure :-   Click on AutoCAD application and open this application Type QNEW…

        Creation of geometries by Coordinate system methods using AutoCad   Aim : To Create the geometries using all the coordinates system methods. To use the Line tool to create the geometries and to use circle tool where it is required. The types of Coordinate systems : Absolute Coordinates…

     Project : G+1 floor Residential Plan according to Vaastu Shastra and Its Load Calculation   Aim Of Project : To sketch G+1 floor residential plan, according to Vaastu Shastra, and list down the names of the structural drawings required to be provided to the site for construction. To calculate the individual corresponding…

Project on : Concrete Mix Design for various grades of Concrete           Q. Calculate the Concrete Mix Design for M35 grade concrete with fly ash  Ans:-   Step -1. Stipulations for proportioning :   Grade designation:  M35 Type of cement:  OPC 43 grade Maximum…