Benchmarking

WIRING HARNESS ASSEMBLY STRUCTURE - CONNECTOR DEFINITION :             CONNECTOR DEFINITIONS IN CATIA V5 :   Deutsch DT06-08SA :   Connector Mating Side: Create midpoint on the contact face of mating side of Connector in Mechanical Part Design Wire Bundle…

modelling of yatch INTRODUCTION    In this project we are to learn the entire modeling of yacht tutorial on solid works and solid works visualize. The different components of the yacht we deal with are:1. Propeller2. Radar3. Blueprint setup4. Hull 5. Garage door 6. Front seat 7. Middle seat 8. Rear seat9. Superstructure…

INTRODUCTION                         in this project we will try to understand and learn the features which are used to do a part of rendering and modeling by using solid works    OBJECTIVES              it is…

                                                        SHEET METAL Bracket-II   OBJECTIVIES              to design an shett metal using…

                                                             SHEET METAL BRACKET  OBJECTIVES              To design a bracket…

                                                                                           …

                                                                              BOX ASSEMBLY DESIGN USING NX CAD Objective:…

OBJECTIVES           How do we use the command in sheet metal and if any problem comes while doing the use of commands how can we solve them  INDRODUCTION              In the project we will learn the step by step procedure to design a sheet metal casing…

BACK DOOR           The back ddoor or the tail gate end is the pannel that covers the boot of an automobile . it ennable to access to the luggage area . A hinge allows the backdoor to raise while the devices like string or gasstray is used to hold the door in the position       …

ROOF   INTRODUCTION               An automobile roof or car top is the portion of an automobile that sits above the passenger compartment, protecting the vehicle occupants from sun, wind, rain, and other external elements. Because the earliest automobiles…

section module                Section Modulus is the geometric property of the given cross-section of any shaft or beam structures. It is the direct measure of the strength of the shaft section or the beam section. Higher the section modulus of a structure, the more the…

FENDER             A fender is the part of a car, truck, motorcycle, or other vehicles that frames or covers a wheel well. Its main purpose is to prevent debris, rocks, mud, liquids, sand, and other road debris from getting thrown in the air while the tire rotates.The “fender” typically…

FENDERS            The fender on a car is located at the front on either side, and at the back on either side. The wheels are located immediately behind in the case of the front fenders, and immediately in front of the rear fenders.               there…

1: HOOD           The hood or bonnet is the hinged cover over the engine of motor vehicles. Hoods can open to allow access to the engine compartment, or trunk on rear-engine and some mid-engine vehicles) for maintenance and repair            On front-engined cars, the hood may be hinged at either the front or the rear…

under body coating                  The coating is to check rust especially in the body components like frame rails along with other exposed metal parts.Underbody coating is usually a dense cladding (often based on rubber) applied uniformly to the undercarriage of the automobile. It is normally sprayed or painted on when…

2.Benchmarking                 Benchmarking is the technical word of comparison between similar process , service and product  . in vehicle development process in predesign and development the benchmarking is divided in to two types they are          …

the requied data is given below

the assembly of the cv joint and the quick return mechanism are given below

the req ppt and the cad file is given below

 the B piller and the cad part is given below

    TOOLING AXIS CREATION                 take the frnd surface of the door apllique and then place the point on the point on the surface so the point is taken as the tooling axis and the line is allowed to extend from the point.

    TOOLING AXIS          in thisn part the tooling axis is created by taking the extraxt of the base of the coin holder and place the poin on the center and thus the tooling axis in created           but for the dog houise the draft should be given in side to…

            After completing the switch bezel in solid model go to generative shape design and then go to insert then select analysis then from there select feature drat analysis . before that select the custamised view to material mode amnd after that select the analysis under the running point and place it on the tooling…

    Report          after completing the switch bezel in solid model go to generative shape design and then go to insert then select analysis then from there select feature drat analysis . before that select the custamised view to material mode amnd after that select the analysis…

 AFTER tooling axis select the analysis mode and analyze and now use the new draft direction and make it align by tooling axis by draging it and now the class a apears green colour if it appear blue clour use the invert option so that we will get the green colour

      the given coin holder is drafted and it allowed to be manufactured          in here the maximum erib thickness can be given by 0.4 , therefore the thickness can be calculated byy W=0.4*thickness of the base and the height can be measured by 5*thickness and the maximum draft…

          *   the draft angle is 2 deg therefore the coin holder design is allowed to manufacture