The Neon Roof Crash Analysis in Hypercrash

OBJECTIVE:            In this challenge we have to compare the the results between the simulations ran with 100000N and 500000N.         Perform a static structural analysis on a Rail wheel and Track setup.                   …

  OBJECTIVE:            To perform the tension and torsion test on the given specimen. REPORT:        TENSILE TEST:            Initially the model has been Imported and the Material steel 1006 is selected to perform the analyse.  …

  OBJECTIVES:            To perform a transient structural analysis on a double universal joint with a spring using three different materials: Structural Steel, Stainless Steel and Titanium alloy REPORT:          Initially the Universal Joint model has been…

Objective:          To perform the Roof crash analysis of the Neon BIW roof crash model and get the output results plot force vs displacement and check that the FMVSS 216 target load of 47,000 N has been met and plot the energy vs time curves. Procedure: The model imported via radioss solver deck…

AIM:    To Write code to fit a linear and cubic polynomial for the Cp data, and Plot the linear and cubic fit curves. PROGRAM: Here comes the code for curve fit linear clear all close all clc %preparing the data cp_temp = load('data'); temp = cp_temp(:,1); cp = cp_temp(:,2); %plotting plot(temp,cp,'linewidth',3);…

OBJECTIVES:            To perform the analysis to simulate a sphere pressing on a plate.Using Structural steel for both sphere and plate but the material of the plate must be Non Linear. REPORT:          Initially the Sphere model has been imported and the rename has…

OBJECTIVES:           To perform a parametric study using 3 different values of thickness for the car body.  REPORT:           Initially the car model has been imported and the rename has been done.          And unwanted Components are…

AIM:      To simulate a bullet penetrating into a bucket with 3 Non-linear material and compare the results like stress and the total deformation.   REPORT:       Intially the model is imported and the rename has been done.       And Al-1100 is for bucket and the TANTALUM…

  OBJECTIVES:              To simulate the rolling operation on a work piece made of copper.  REPORT:            Initially the Sphere model has been imported and the rename has been done.           …

OBJECTIVE:      To perform the side crash analysis of the Neon BIW model on the rigid pole and get the output results intrusion at B-pillar, Hinge, Fuel tank and peak velocity at the inner node of the door and sectional force on the cross-section.   PROCEDURE: The frontal model imported via radioss…

OBJECTIVE:          To perform the frontal crash analysis of Neon BIW is by creating a rigid wall in the front of the bumper to impact.          To reach the target weight of 700kg add mass in the front neon model. By following given conditions and to Analyse and compare…

Objective:         To compare the base setup simulation results and different kinematic condition simulation results and run the simulations as per the below cases, Run the crash tube model. Change the value of Inacti=6 and run it. Create the type 11 contact and run. Remove both notches and…

OBJECTIVE:                 The objective of this challenge is to mesh the given component (SIDE DOOR) has per the given quality criteria and maintain the mesh flow.                 …

OBJECTIVE:                    The objective of this challenge is to Morph the given side body to desired shape and also to create the macro for the component. REPORT:             Morphing…

OBJECTIVE:                 The objective of this challenge is to mesh the given component (BACK DOOR) has per the given quality criteria and maintain the mesh flow.                 …

OBJECTIVE:                    The main objective of this challenge is to perform and study about 3D mesh for the given component using given parameters. REPORT:           To learn and perform…

OBJECTIVE:                 The objective of this challenge is to mesh the given  component (HOOD) has per the given quality criteria and maintain the mesh flow.                 …

  OBJECTIVE: The objective of this project is to write a code to parse the NASA Thermodynamics data file. To calculate the \'Specific heat,Entropy,Enthalpy\' of Various gas species by using given coefficients.   CODE FOR NASA PARSING:                      …