Hemming and surface mesh with Mid-plane of a front panel of Car using ANSA

OBJECTIVE         The objective of the challenge is to perform the frontal crash for the given simplified car model and to analyze the changes and the errors in energies due to the impact of the car on the rigid wall. PROCEDURE CREATE INTERFACE  ----- As to create the interface of type7 which is…

OBJECTIVE:                 The objective of this assignment is to perform a side crash analysis for the given simplified car model and observe the sectional forces and displacements and energies. PROCEDURE: CREATE INTERFACE  ----- As to create the interface of type7 which is…

OBJECTIVE              This challenge is to mesh the given bumper assembly and simulate the crash tube model under the different case of changes with considering the notches at different area in a crash tube as changed with some required parameters. BUMPER MESH        Creating…

OBJECTIVE                As the objective is to compare the results by which in changing the material properties of the model as under consideration of 7 cases of action in simulation. PROCEDURE                    There 7 cases applied…

OBJECTIVE           The main objective of the challenge is to Read the Run file of this model and simulating the model by changing the property parameters as specified and compare the between the graphs obtained after the formulation parameters changed with the normal Run file simulation.…

OBJECTIVE             The objective of the given challenge is to create the 2D and 3D mesh for housing and arm bracket and performing the changes in the run file and the engine file.As of same changes for another model. PROCEDURE CREATE MESH FOR HOUSING   Import the given model using…

OBJECTIVE:             The objective of this challenge is to clean up the geometry of the given model and the shell mesh is to be carried out for the model with given parameters as required. PROCEDURE: GEOMETRY CLEAN UP EXTRACTION OF MID SURFACE CLEAN THE MID SURFACE GEOMETRY CREATE 2D MESH…

OBJECTIVE           The main objective of this challenge is to script a program for the data analysis for the given data. INSTRUCTIONS TO DO WITH DATA ANALYSIS The script to be written according to the data that column as input and plotting the respective columns in separate images with each of…

OBJECTIVE           The objective of this program is to get the best fit from the equation of linear and cubic for the curve by calculating the error values. hence the curve is plotted using the data given. PROGRAM import numpy as np import matplotlib.pyplot as plt from scipy.optimize import…

OBJECTIVE        The objective is to determine the pressure that is required to break the thickness of ice using the air-cushion vehicle muller and by using mathematical modeling by using the newton raphson method using python. NEWTON RAPHSON METHOD           The newton raphson…

OBJECTIVE             The objective of this challenge is to simulate the transient behavior of the simple pendulum with help of second-order ODE in which could describe the ball behavior w.r.t time. PROCEDURE           According to this equation which is…

OBJECTIVE         The main stipulation of this challenge is to create the pressure vs volume diagram for the otto cycle and the thermal efficiency of the cycle performed with given data. PROCESS IN THE OTTO CYCLE        As the process carried out in the otto cycle is shown according…

OBJECTIVE       The main stipulation of the project is to simulate the forward kinematics of 2R robotics arm by programming with python. EXPRESSION USED IN THE PROGRAM      For the first link end coordinates       `x_1= l_1*cos theta_1`        `y_1=l_1*sin…

OBJECTIVE       The main stipulation of the project is to calculate the drag force against the cyclist by programming with python. EXPRESSION USED TO CALCULATE DRAG FORCE       The factors involved in calculating the drag force against the cyclist are Velocity Drag_coeffficient Density of…

OBJECTIVE             The decisive possession of this activity is to perform the geometry preprocessing and meshing the given set of IP substrate closure models for structural analysis. PROCEDURE           The steps followed to achieve this meshing with given…

OBJECTIVE               The main intention of this challenge is to surface wrap the given model - Engine, Transmission unit, Gearbox and merging this three-part into a single volume model. WHAT IS SURFACE WRAPPING              surface wrapping is…

OBJECTIVE            The main objective of this challenge is to make the given hood model surface mesh the panel with the differentiated PID\'s for it. And at last hemming process is to be done the panel. WHATS\'S HEMMING IN AUTOMOTIVE SECTOR?           Hemming…

OBJECTIVE                 The preeminent dispassionate of this challenge is to Mesh the give BMW M6 sample model and to hack out the TOPOLOGICAL errors and geometrical errors over in the given model and to make the meshing task without having even one of the surface errors even after…

OBJECTIVE                  The dynamic motivate is to mesh the model of Turbocharger with the tools taught over in lecture and the clearing in the Topological error and geometrical error and performance of the turbocharger by using volumetric meshing. PROCEDURE    …

OBJECTIVE                 The main intention of this challenge is to mesh the given Modelled product by illustrating with given Aspects using ANSA TOOL PROCEDURE Importing the given model into work space and converting the geomentry according to the meshing anotonmy  After…