3D Creation of Celing, Roof, Architectural plan, Structural plan, Sectional view, Elevation view and Camera specific view for a house plan using REVIT

1.

AIM:

To draw the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level using revit software and commands.

INTRODUCTION:

Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level.

PROCEDURE:

Open the week 3 final drawing to begin with.Our first task is to create a ceiling on top of wall at the first floor level.From the properties browser click on the FIRST FLOOR LEVEL.

Now in the architectural tab click on ceiling as shown in figure.Now from the modify/ create ceiling panel select sketch ceiling option as shown.

The ceiling is then sketched along the boundary of the first floor as shown and then click on the tick option at the top apply it.The ceiling is completely placed and the three dimensional isometric realistic view and the elevation view is as shown is as shown.

RESULT:

draw the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level using revit software and commands is drawn.

2.

AIM:

To Model a roof above the ceiling by selecting the footprints of the ceiling. Using the adjustment toolbars appearing on-screen adjust the roof slope to 10 degrees using revit software and command.

INTRODUCTION:

Model a roof above the ceiling by selecting the footprints of the ceiling. Using the adjustment toolbars appearing on-screen adjust the roof slope to 10 degrees.

PROCEDURE:

In the architectural tab select the Roof option and then select Roof by footprints options to draw the roof.From the modify/create roof footprint option select the boundary line option.

Now create the roof boundary along the border of the house as shown and then click on the tick mark on top.

The roof is now created and the 3D isometric realistic view of the residential unit is as shown select the roof and in the properties section change the slope of roof from 30 degree to 10 degree as shown.

RESULT:

Model a roof above the ceiling by selecting the footprints of the ceiling. Using the adjustment toolbars appearing on-screen adjust the roof slope to 10 degrees using revit software and command is applied.

3.

AIM:

To Using the file saved from weeks 2 to 4, create plan views for ground floor level and first-floor level including all the walls, floors, and components. Separate them to architecture and structural plans using revit software and commands.

INTRODUCTION:

Using the file saved from weeks 2 to 4, create plan views for ground floor level and first-floor level including all the walls, floors, and components. Separate them to
architecture and structural plans

a. Architecture plan must have walls, floors, and all the components placed within the building
b. Structure plan must have details of only walls, floors, and columns

PROCEDURE:

To create the architecture plan follow these steps In the view menu select the plan view option and then select the floor plan from the drop down menu.

From the new floor plan dialogue box select the select the ground floor level and click ok. The Floor plan view of ground floor is now created and in the properties browser rename the view to GF architectural plan for our convenience and GF architectural view is as shown.

In the same way as above first floor architectural plan was created In the view menu select the plan view option and then select the Structural plan from the drop down menu. From the new floor plan dialogue box select the select the ground floor level and click ok.

The Structural plan view of ground floor is now created and in the properties browser rename the view to GF Structural plan for our convenience and GF Structural view is as shown. The view is like this as the columns and beams are not placed in the residential unit.In the same way as above first floor Structural plan was created.

RESULT:

Using the file saved from weeks 2 to 4, create plan views for ground floor level and first-floor level including all the walls, floors, and components. Separate them to architecture and structural plans using revit software and commands is applied.

4.

AIM:

To Using annotate toolbar add dimensions to all the walls and floors with reference to the longitudinal and transverse grids created in the project file using revit software and commands.

INTRODUCTION:

Using annotate toolbar add dimensions to all the walls and floors with reference to the longitudinal and transverse grids created in the project file

a. The architecture plan dimensions include details on where the components are placed within the buildings with relation to grids. Overall dimensions are sufficient for architecture plans

b. The Structure plan dimensions must include details on the position of all the walls and interior walls with reference to grids. Locate all the framing components of the building with reference to a fixed point using Structural plans

PROCEDURE:

Open the GF architectural architectural plan to give the dimensions.Now in the annotate tab select the linear option to provide the dimensions.

The horizontal and vertical dimensioning was done as to shown.

Now in the architetural tab select grid options to provide the longitudinal and transverse grids. The transverse and longitudinal grids was marked correspondong to wall centreline as shown.

RESULT:

Using annotate toolbar add dimensions to all the walls and floors with reference to the longitudinal and transverse grids created in the project file using revit software and commands is created.

5.

AIM:

To Create a sheet template from the view tab and adjust the parameters on the sheet to add appropriate views uing revit software and commands.

INTRODUCTION:

Create a sheet template from the view tab and adjust the parameters on the sheet to add appropriate views.

PROCEURE:

In the view tab click on the sheet option to create a sheet templateFrom the new sheet dialogue box that appears select A1 metric and click ok.

A new sheet layout is now created as shownNow inorder to place a view click on the place view option in the view panel

From the views list select the desired view of our choice.The ground floor plan is now placed in the template created.

RESULT:

Create a sheet template from the view tab and adjust the parameters on the sheet to add appropriate views uing revit software and commands is created.

6.

AIM:

To Using the elevation tab create the elevation views, looking at your building from East, North, South, and West uisng revit software and command.

INTRODUCTION;

Using the elevation tab create the elevation views, looking at your building from East, North, South, and West.

PROCEDURE:

In order to create the elevation views select elevation in the view panel.Now place the views in the North, South, East and West directions as shown.

In the properties browser under the elevation tab the view names will be present, rename them to North, South, East and West,East elevation view.

RESULT:

Using the elevation tab create the elevation views, looking at your building from East, North, South, and West uisng revit software and command is created.

7.

AIM:

To Produce section cut through each room either cutting across longitudinally or in a transverse direction using revit software and commands.

INTRODUCTION:

Produce section cut through each room either cutting across longitudinally or in a transverse direction.

PROCEDURE:

To draw the sections select the section option under the view panel.Now draw a line through the required rooms to obtain the section of that particular room.

view of the command has section views of transverse and conditions.

RESULT:

Produce section cut through each room either cutting across longitudinally or in a transverse direction is viewed.

8.

AIM:

To Classify the views, Plan Views, Section Views, and Elevation views to either Design or Documentation category using Properties browser using revit software and command.

INTRODUCTION:

Classify the views, Plan Views, Section Views, and Elevation views to either Design or Documentation category using Properties browser.

PROCEDURE:

In the properties browser we can see views.Now click on the + icon near to Views to open the the various views.The various views are as follows: Floor plans, Ceiling plans, 3D views, Elevations and sections.Click on the + icon near to floor plan to open the floor plan views.

The various views which we have cretaed earlier under the Floor plans will be listed as shown.Click on the + icon near to Ceiling plans to open the ceiling plan views.

The various views which we have cretaed earlier under the ceiling plans will be listed as shown.Click on the + icon near to 3D views to open the 3D views.

The various views which we have cretaed earlier under the 3D view will be listed as shown.Click on the + icon near to Elevations to open the elevation views.

The various views which we have cretaed earlier under the Elevation view will be listed as shown.Click on the + icon near to Section to open the Sectional views.The various views which we have cretaed earlier under the Sheet template view will be listed as shown.

plan view:

section view:

elevation view:

RESULT:

Classify the views, Plan Views, Section Views, and Elevation views to either Design or Documentation category using Properties browser is arrived.

9.

AIM:

To Using the sheet template produced create multiple sheets revit command and software.

INTRODUCTION:

Using the sheet template produced create multiple sheets as follows
a. A 101- Ground Floor Architecture Plan
b. A 102- First Floor Architecture Plan
c. A 103- Roof Plan
d. S 101- Ground Floor Structural Plan
e. S 102- First Floor Structural Plan
f. S 103- Roof Framing Plan
g. A-201- North-South Elevations
h. A-202- East-West Elevations

Add additional sheets based on the sections created in your Revit file.

PROCEDURE:

In the view tab click on the sheet option to create a sheet template.From the new sheet dialogue box that appears select A1 metric and click ok.

A new sheet layout is now created as shown

Now inorder to place a view click on the place view option in the view panelFrom the views list select the desired view of our choice.

The following plan is now placed in the template created.

A 101- Ground Floor Architecture Plan

A 102- First Floor Architecture Plan

A 103- Roof Plan

S 101- Ground Floor Structural Plan

S 102- First Floor Structural Plan

S 103- Roof Framing Plan

A-201- North-South Elevations

A-202- East-West Elevations

RESULT:

Using the sheet template produced create multiple sheets revit command and software is created.

10.

AIM:

To Create a camera-specific view or a 3D view in each room ( living, dining, bedroom). Based on the views create a new set of sheets starting A-501 (you can add as many sheets after, 502, 503.. n)to place the 3D view images. Produce the sheets as a part of project drafting using revit software and commands.

INTRODUCTION:

Create a camera-specific view or a 3D view in each room ( living, dining, bedroom). Based on the views create a new set of sheets starting A-501 (you can add as many sheets after, 502, 503.. n)to place the 3D view images. Produce the sheets as a part of project drafting.

PROCEDURE:

in a revit software the view tab contains camera view and the camera view is working under how the angle was set by viewing angle and it comsiderate the position of the camer as well.

the viewing angle of the camera is ready to serve mode we only have to set the viewing angle of the camera alone and it set to sheet view to present the actual model designed are drawned by the modeler.

A-501

A-502

A503

Create a camera-specific view or a 3D view in each room ( living, dining, bedroom). Based on the views create a new set of sheets starting A-501 (you can add as many sheets after, 502, 503.. n)to place the 3D view images. Produce the sheets as a part of project drafting using revit software and commands are arraged.