3D Creation of Celing, Roof, Architectural plan, Structural plan, Sectional view, Elevation view and Camera specific view for a house plan using REVIT
1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level
Aim:
To draw the Model a Ceiling from the architecture tab above the walls at the first-floor level
Commands Are used:
- Architecture
- Wall
- Ceiling
Procedure:
- First We select the architectural tab create the new drawing
- And we do save the file name as project
- Change the dimension to the unit as feet
- Next we do the ceiling tab and click it
- To click on the sketch ceiling and mark the boundary line
- Once compete the boundary attach the line created the ceiling once verified the 3d
RESULT:
Finally we draw the ceiling at the first floor level
2) Model a roof above the ceiling by selecting the footprints of the ceiling. Using the adjustment toolbars appearing on-screen adjust the roof slope to 10 degrees
Aim:
To draw the roof adjustment toolbars appearing on-screen adjust the roof slope to 10 degrees
Commands Are used:
- Architecture
- Wall
- Roof
- Slope
Procedure:
- First We select the architectural tab create the new drawing
- And we do save the file name as project
- Change the dimension to the unit as feet
- We draw the ground floor plan and draw the roof
- To click the architectural tab and click roof at the foot print
- To mark the boundary line attach the roof
- To click on the slope option to change the slope as 10 degree
RESULT:
Finally we draw the roof over the 10 degree slope
3) Using the file saved from weeks 2 to 4, create plan views for ground floor level and first-floor level including all the walls, floors, and components. Separate them to
architecture and structural plans
Aim:
ToUsing the file saved from weeks 2 to 4, create plan views for ground floor level and first-floor level including all the walls, floors, and components.
Commands Are used:
- Architecture
- View
- Plan view
Procedure:
- IN this challenge we have already on the ground and the floor plan
- So We diirectly go on the view tab
- And click the plan views
- To convert the floor plan for ground floor plan and first floor plan respetively
- To click the edit type for once checked and click ok
Once click the ok the floor plan as been created and named as the ground floor plan
we get the ground floor and the first floor plan 
Structural plan as same as click the plan view and click the structural plan
Ground floor as been created
First floor strctural plan as been created
RESULT:
Finally we draw the ground floor and first floor plan strctural plan
4) Using annotate toolbar add dimensions to all the walls and floors with reference to the longitudinal and transverse grids created in the project file
a. The architecture plan dimensions include details on where the components are placed within the buildings with relation to grids. Overall dimensions are sufficient for architecture plans
b. The Structure plan dimensions must include details on the position of all the walls and interior walls with reference to grids. Locate all the framing components of the building with reference to a fixed point using Structural plans
Aim:
To Using annotate toolbar add dimensions to all the walls and floors with reference to the longitudinal and transverse grids created in the project file
Commands Are used:
- Architecture
- Wall
- Annotate
Procedure:
- We go for an annotate tab
- To get an the floor plan and the strctural plan to mark the outer and inner boundary
To annotate tab mesaure the room dimension and outer boundary line both architectural and structural plan
RESULT:
Finally we get the measure using of the annotate tab
5) Create a sheet template from the view tab and adjust the parameters on the sheet to add appropriate views
Aim:
To Create a sheet template from the view tab and adjust the parameters on the sheet to add appropriate views
Commands Are used:
- Architecture
- View
- Sheet
Procedure:
- To click the view tab and click the sheet
After that one tab will shows choose the paper size
After the paper will be viewed to trag the plan paste at the sheet
RESULT:
Finally we draw the A1 sheet and apporiprate view
6) Using the elevation tab create the elevation views, looking at your building from East, North, South, and West
Aim:
To Using the elevation tab create the elevation views, looking at your building from East, North, South, and West
Commands Are used:
- Architecture
- Wall
- View
- Elevation
Procedure:
- To click the view tab and click the elevation
- To mark the elevation view and paste
- To change the name as north east west and south
After the marking of the elevation
To click the north view as shows
To click the East view as shows
To click the West view as shows
To click the South view as shows
RESULT:
Finally we get the elevation at the direction views
7) Produce section cut through each room either cutting across longitudinally or in a transverse direction
Aim:
To Produce section cut through each room either cutting across longitudinally or in a transverse direction
Commands Are used:
- Architecture
- View
- Section
Procedure:
- Go for an architectural tab and choose the section tab
- To click the ground floor plan to cut the section in bedroom
To cut the bedroom the elevation view
In a bedroom as section viewed
In a Master bedroom as section viewed
RESULT:
Finally we draw the section view for the bedroom
8) Classify the views, Plan Views, Section Views, and Elevation views to either Design or Documentation category using Properties browser
Aim:
To Classify the views, Plan Views, Section Views, and Elevation views to either Design or Documentation category using Properties browser
Commands Are used:
- Architecture
- Property browser
Procedure:
- In that the property browser might have the structural drawing , floor plan, ceiling plan , elevation, section and renter drawings as it
- The property browser shows the easy way of access
RESULT:
Finally we get the category using Properties browser
9) Using the sheet template produced create multiple sheets as follows
a. A 101- Ground Floor Architecture Plan
b. A 102- First Floor Architecture Plan
c. A 103- Roof Plan
d. S 101- Ground Floor Structural Plan
e. S 102- First Floor Structural Plan
f. S 103- Roof Framing Plan
g. A-201- North-South Elevations
h. A-202- East-West Elevations
Add additional sheets based on the sections created in your Revit file
Aim:
To Using the sheet template produced create multiple sheets
Commands Are used:
- Architecture
- View
- Sheet
Procedure:
- To click the view tab and click the sheet
After that one tab will shows choose the paper size
After the paper will be viewed to trag the plan paste at the sheet
The ground floor plan named as A101
The first floor plan named as A102
The ground roof plan named as A103
The ground floor Strctural plan named as S101
The first floor Strctural plan named as S102
The roof Strctural plan named as S103
The elevation north and south plan named as A201
The elevation east and west plan named as A202
RESULT:
Finally Classify the views, Plan Views, Section Views, and Elevation views to either Design
10) Create a camera-specific view or a 3D view in each room ( living, dining, bedroom). Based on the views create a new set of sheets starting A-501 (you can add as many sheets after, 502, 503.. n)to place the 3D view images. Produce the sheets as a part of project drafting.
Aim:
To reate a camera-specific view or a 3D view in each room
Commands Are used:
- Architecture
- View
- Camera
Procedure:
- To click the view tab go to the camera tab and click it
- To set the camera view at the bedroom and the hall
- To complete the camera view to change the realistic
- To named as the A501
- To named as the A502
- To named as the A503
RESULT:
Finally we Create a camera-specific view