3D Creation of Celing, Roof, Architectural plan, Structural plan, Sectional view, Elevation view and Camera specific view for a house plan using REVIT
1)
Aim :-
Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level by using Revit.
Procedure :-
* Open the revit software.
* Next we select model-new project.
* Template file select as Architectural template.
* Next click on OK.
* In top left corner click on file menu it showing save or shortcut key as control+s.
* We click on save,type the project name click the save option.
* Next we can create the recidential layout of wall option under the achitecture tab.
* Unit set as feet.
* In architectural tab, we select ceiling option.
* Next we select, sketch ceiling then click pick line option.
* Select all the inner main wall edges then press enter.
* Finally it creates ceiling.
Result :-
Complete the based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level by using Revit.
2)
Aim :-
Model a roof above the ceiling by selecting the footprints of the ceiling. Using the adjustment toolbars appearing on-screen adjust the roof slope to 10 degrees by using Revit.
Procedure :-
* Open the revit software.
* Next we select model-new project.
* Template file select as Architectural template.
* Next click on OK.
* In top left corner click on file menu it showing save or shortcut key as control+s.
* We click on save,type the project name click the save option.
* Next we can create the recidential layout of wall option under the achitecture tab.
* Unit set as feet.
* In architectural tab, we select roof.
* In the roof option select roof by Foot print.
* Then select outer edge of the walls press enter.
* Roof will be created.
* Next goto roof properties slope angle changes to 10degress.
Result :-
Complete model a roof above the ceiling by selecting the footprints of the ceiling. Using the adjustment toolbars appearing on-screen adjust the roof slope to 10 degrees by using Revit.
3)
Aim :-
Using the file saved from weeks 2 to 4, create plan views for ground floor level and first-floor level including all the walls, floors, and components. Separate them to
architecture and structural plans by using Revit.
Procedure :-
* Open the revit software.
* Next we select model-new project.
* Template file select as Architectural template.
* Next click on OK.
* In top left corner click on file menu it showing save or shortcut key as control+s.
* We click on save,type the project name click the save option.
* Next we can create the recidential layout of wall option under the achitecture tab.
* Unit set as feet.
* Goto ground floor plan view.
* In the view tab,Click on plan view.
* In the plan view, we select floor plan option.
* It directly shows architectural plan.
* Next in the plan view, we select structural plan.
* It directly shows structural plan.
Result :-
Complete using the file saved from weeks 2 to 4, create plan views for ground floor level and first-floor level including all the walls, floors, and components. Separate them to
architecture and structural plans by using Revit.
4)
Aim :-
Using annotate toolbar add dimensions to all the walls and floors with reference to the longitudinal and transverse grids created in the project file by using Revit.
Procedure :-
* Open the revit software.
* Next we select model-new project.
* Template file select as Architectural template.
* Next click on OK.
* In top left corner click on file menu it showing save or shortcut key as control+s.
* We click on save,type the project name click the save option.
* Next we can create the recidential layout of wall option under the achitecture tab.
* Unit set as feet.
* Goto annotate tab, select linear option to provide longitudinal dimensions.
* Then select aligned option to provide transverse dimensions.
Result :-
Complete using annotate toolbar add dimensions to all the walls and floors with reference to the longitudinal and transverse grids created in the project file by using Revit.
5)
Aim :-
Create a sheet template from the view tab and adjust the parameters on the sheet to add appropriate views by using Revit.
Procedure :-
* Open the revit software.
* Next we select model-new project.
* Template file select as Architectural template.
* Next click on OK.
* In top left corner click on file menu it showing save or shortcut key as control+s.
* We click on save,type the project name click the save option.
* Next we can create the recidential layout of wall option under the achitecture tab.
* Unit set as feet.
* In the view tab, we select sheet option.
* After click on sheet option select m1 metric sheet then click on ok.
* Drag any view to the sheet then adjust the scale.
Result :-
Complete create a sheet template from the view tab and adjust the parameters on the sheet to add appropriate views by using Revit.
6)
Aim :-
Using the elevation tab create the elevation views, looking at your building from East, North, South, and West by using Revit.
Procedure :-
* Open the revit software.
* Next we select model-new project.
* Template file select as Architectural template.
* Next click on OK.
* In top left corner click on file menu it showing save or shortcut key as control+s.
* We click on save,type the project name click the save option.
* Next we can create the recidential layout of wall option under the achitecture tab.
* Unit set as feet.
* In the view tab, we select elevation option place elevation cursor in any side of the plan.
* Then goto elevation property change the direction name.
* Same follow the remaining directions.
Result :-
Complete using the elevation tab create the elevation views, looking at your building from East, North, South, and West by using Revit.
7)
Aim :-
Produce section cut through each room either cutting across longitudinally or in a transverse direction by using Revit.
Procedure :-
* Open the revit software.
* Next we select model-new project.
* Template file select as Architectural template.
* Next click on OK.
* In top left corner click on file menu it showing save or shortcut key as control+s.
* We click on save,type the project name click the save option.
* Next we can create the recidential layout of wall option under the achitecture tab.
* Unit set as feet.
* Goto plan view.
* Select any room, click on view tab then select section cut the room as longitudinally and transverse direction.
* Goto property browser, Click on sections it shows created section views.
* Click on these views directly shows created section view.
Result :-
Complete produce section cut through each room either cutting across longitudinally or in a transverse direction by using Revit.
8)
Aim :-
Classify the views, Plan Views, Section Views, and Elevation views to either Design or Documentation category using Properties browser by using Revit.
Procedure :-
* Open the revit software.
* Next we select model-new project.
* Template file select as Architectural template.
* Next click on OK.
* In top left corner click on file menu it showing save or shortcut key as control+s.
* We click on save,type the project name click the save option.
* Next we can create the recidential layout of wall option under the achitecture tab.
* Unit set as feet.
* After creation of floors,elevations,structural views then property browser shows as per below.
Result :-
Complete classify the views, Plan Views, Section Views, and Elevation views to either Design or Documentation category using Properties browser by using Revit.
9)
Aim :-
Using the sheet template produced create multiple sheets as follows
a. A 101- Ground Floor Architecture Plan
b. A 102- First Floor Architecture Plan
c. A 103- Roof Plan
d. S 101- Ground Floor Structural Plan
e. S 102- First Floor Structural Plan
f. S 103- Roof Framing Plan
g. A-201- North-South Elevations
h. A-202- East-West Elevations
Add additional sheets based on the sections created in my Revit file
Procedure :-
* Open the revit software.
* Next we select model-new project.
* Template file select as Architectural template.
* Next click on OK.
* In top left corner click on file menu it showing save or shortcut key as control+s.
* We click on save,type the project name click the save option.
* Next we can create the recidential layout of wall option under the achitecture tab.
* Unit set as feet.
* In the view tab, we select sheet option.
* After click on sheet option select m1 metric sheet then click on ok.
* Drag any view to the sheet then adjust the scale.
* In the sheet name changes as given name in the aim.
* Same procedure follow
a. A 101- Ground Floor Architecture Plan
b. A 102- First Floor Architecture Plan
c. A 103- Roof Plan
d. S 101- Ground Floor Structural Plan
e. S 102- First Floor Structural Plan
f. S 103- Roof Framing Plan
g. A-201- North-South Elevations
h. A-202- East-West Elevations
Result :-
Complete using the sheet template produced create multiple sheets as follows
a. A 101- Ground Floor Architecture Plan
b. A 102- First Floor Architecture Plan
c. A 103- Roof Plan
d. S 101- Ground Floor Structural Plan
e. S 102- First Floor Structural Plan
f. S 103- Roof Framing Plan
g. A-201- North-South Elevations
h. A-202- East-West Elevations
Add additional sheets based on the sections created in my Revit file
10)
Aim :-
Create a camera-specific view or a 3D view in each room ( living, dining, bedroom). Based on the views create a new set of sheets to place the 3D view images. Produce the sheets as a part of project drafting by using Revit.
Procedure :-
* Open the revit software.
* Next we select model-new project.
* Template file select as Architectural template.
* Next click on OK.
* In top left corner click on file menu it showing save or shortcut key as control+s.
* We click on save,type the project name click the save option.
* Next we can create the recidential layout of wall option under the achitecture tab.
* Unit set as feet.
* Goto view tab, in the 3D view option, click in camera option.
* Place the camera at room,then camera face rotate which side we want in view
* In the view tab, we select sheet option.
* After click on sheet option select m1 metric sheet then click on ok.
* In the property browser,click on 3D views it shows before we create the 3D camera views.
* Drag the 3D view to the sheet then adjust the scale.
Result :-
Complete create a camera-specific view or a 3D view in each room ( living, dining, bedroom). Based on the views create a new set of sheets to place the 3D view images. Produce the sheets as a part of project drafting by using Revit.