3D Creation of Celing, Roof, Architectural plan, Structural plan, Sectional view, Elevation view and Camera specific view for a house plan using REVIT

1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level.

AIM :

To model a ceiling from the archietecture tab above the walls @ the first floor level.

INTRODUCTION :

The ceiling finish or product is attached to the ceiling battens under the roof framing and is generally a plasterboard of some form. Typically we see ceilings as the flat plane above us that hides the roof or floor framing.

Ceilings help create enclosure of and separation between spaces, they help to control the diffusion of light and sound around a room, and help prevent the passage of sound between rooms

PROCEDURE :

STEP 1:

• First open the revit sofware, and select the ceiling option from the archietecture tool bar

STEP 2:

• After selecting the ceiling option then selecting the each room one by one,
• then the ceiling will be created as shown in fig.

STEP 3:

• Here we can see the ceiling in 3 Dimensional view as shown in the below fig.

RESULT :

The Ceiling has been modeled successfully from the archietecture tab above the walls @ the first floor level.

2) Model a roof above the ceiling by selecting the footprints of the ceiling. Using the adjustment toolbars appearing on-screen adjust the roof slope to 10 degrees

AIM :

To Model a Roof above the ceiling by selecting the footprints of the ceiling.

INTRODUCTION :

The roof is part of a building envelope which is the covering on the uppermost part of a building/home. It supported on the walls of the building. It provides for the protection against rain, snow, sunlight, extremes of temperature, and wind. It protects from the weather conditions

PROCEDURE :

STEP 1:

• Open the Archietectural tool bar select the roof by footprint option as shown in below fig.

Step 2:

• Next we select the roof and adjust the roof to 10 degrees by selecting it as shown in the fig,

STEP 3:

• Roof as been created as shown in below

RESULT :

Roof has been created successfully to the model in the revit in detailed manner.

3) Using the file saved from weeks 2 to 4, create plan views for ground floor level and first-floor level including all the walls, floors, and components. Separate them to
architecture and structural plans

a. Architecture plan must have walls, floors, and all the components placed within the building
b. Structure plan must have details of only walls, floors, and columns

AIM :

To create plan view for ground floor level and first floor level including all the walls , floors and components and to seperate them to archietectural and structural plan,.

INTRODUCTION :

• Structural plan view is the default view when you start new template using structural template.
• Most plan include atleast one structural plan , new structural plan created as you can add new levels of the new project. you can cfeate multiple structural plan view types,
• the floor plan view is the default view in a new archietectural project.
• most projects inculde atleast one floor plan
• floor plan views are created automatically as you add new levels to your project

PROCEDURE :

STEP 1:

• First we drawn the archie tectural plans for first floor and second floor as shown.

STEP 2:

• Next we have to draw the structural plan for first and second floor

RESULT :

Created Plan views for ground floor level and first floor level including walls , floors and components and seperate them into archietectural plan and structural plan.

4) Using annotate toolbar add dimensions to all the walls and floors with reference to the longitudinal and transverse grids created in the project file

a. The architecture plan dimensions include details on where the components are placed within the buildings with relation to grids. Overall dimensions are sufficient for architecture plans

b. The Structure plan dimensions must include details on the position of all the walls and interior walls with reference to grids. Locate all the framing components of the building with reference to a fixed point using Structural plans

AIM :

To add dimensions to all the walls and floors with reference to the longitudinal and transverse grids created in the project file.

INTRODUCTION :

• Structural plan view is the default view when you start new template using structural template.
• Most plan include atleast one structural plan , new structural plan created as you can add new levels of the new project. you can cfeate multiple structural plan view types,
• the floor plan view is the default view in a new archietectural project.
• most projects inculde atleast one floor plan
• floor plan views are created automatically as you add new levels to your project

PROCEDURE :

STEP 1:

• Here we drawn longitudinal and transverse grids to thearchietectural plans as shown below,
• and dimensions to the archietectural plans

STEP 2:

• Next we draw longitudinal and transverse grids to the structural plan as shown below,
• and the dimensions to the structural plans

RESULT :

The Dimensiosn are added to the structural floor plan and srchietectural plan,

and the longitudinal and transverse grids are also created in project file.

5) Create a sheet template from the view tab and adjust the parameters on the sheet to add appropriate views

AIM : To create a sheet template from a view tab and adjust the parameters on the sheet to add appropriate views.

INTRODUCTION :

A view template is a collection of view properties, such as view scale, discipline, detail level, and visibility settings. Use view templates to apply standard settings to views. View templates can help to ensure adherence to office standards and achieve consistency across construction document sets.

PROCEDURE :

STEP 1:

• First we click on the sheet option from the view tool bar as shown below,
• After clicking the sheet , the new tab will be visible on the screen,
• In that new tab we select the A1 Metric then the sheet template will be displayed.

STEP 2:

• In the sheet template we insert the first floor plan and second floor plan seperately as shown below,
• Next edit th eproject name and sheet number as shown in the below fig.

RESULT :

Create a sheet template from the view tab and adjust the parameters on the sheet for adding appropriate views.

6) Using the elevation tab create the elevation views, looking at your building from East, North, South, and West

AIM :

To create a elevation views looking at your building from east , north , south and west using the elevation tab.

INTRODUCTION :

Elevation views are part of the default template in Revit Architecture. When you create a project with the default template, 4 elevation views are included: north, south, east, and west. It is in elevation views where you sketch level lines. For each level line that you sketch, a corresponding plan view is created.

PROCEDURE :

STEP 1:

• First we click on the elevation option from the view tool bar as shown below ,

STEP 2:

• Next the elevation from the east will be visible , as shown below

STEP 3:

• Next the elevation from the north wiil be visible , as shown below

STEP 4:'

• Next the elevation from the south will be visible , as shown below

STEP 5:

• Next the elevation from the west will be visible , as shown below

RESULT :

• EAST VIEW

• WEST VIEW

• NORTH VIEW

• SOUTH VIEW

7) Produce section cut through each room either cutting across longitudinally or in a transverse direction

AIM :

To produce section cut through each room either cutting across longitudinally or in a transverse direction.

INTRODUCTION :

Add a section line and crop region to define a new section view. Open a plan, section, elevation, or detail view. Click View tab Create panel (Section). (Optional) In the Type Selector, select a view type from the list, or click Edit Type to modify an existing view type or create a new view type

PROCEDURE :

STEP 1:

• First we click on the section views on the view tool bar , as shown below
• Next we produce the section views of the bedroom as shown in the fig

STEP 2:

• Next we produce section view of the toilet room as shown in the fig.

STEP 3:

• Next we produce section view of the kitchen room as shown in the fig,

STEP 4:

• Next we produce the section view of the living room as shown in the fig.

RESULT :

Created the section of the model in the revit in detailed manner

8) Classify the views, Plan Views, Section Views, and Elevation views to either Design or Documentation category using Properties browser

AIM :

To Classify the views, Plan Views, Section Views, and Elevation views to either Design or Documentation category using Properties browser

INTRODUCTION :

Views within Revit fall into three main categories. One is a coordination view, a view used for design purposes and coordination. Views under the Design (Working Views) fall into this category. Another is a documentation view, a view put onto a sheet making up the deliverables of the project.

PROCEDURE :

STEP 1:

• First we open the project browser the views, plan view, section view, elevation view, are visible in the project browser as shown below
• Next we insert these plans one by one in sheet seperately

STEP 2:

• First we insert the front elevation in the sheet template as shown below,

STEP 3:

• Next we insert the left side elevation in the sheet template as shown in below,

STEP 4:

• Next we insert the right side elevation in the sheet template as shown in below,

STEP 5:

• Next we insert the back side elevation in the sheet template as shown in below,

STEP 6:

• Next we insert the Ground floor plan in the sheet template as shown in below,

STEP 7:

• Next we insert the First floor plan in the sheet template as shown in below,

STEP 8:

• Next we insert the Section 1 in the sheet template as shown in below,

STEP 9:

• Next we insert the Section 2 in the sheet template as shown in below,

STEP 10:

• Next we insert the Section 3 in the sheet template as shown in below,

RESULTS :

Views, Plan views, Section views, Elevation views are classified to design category using properties browser,

9) Using the sheet template produced create multiple sheets as follows
a. A 101- Ground Floor Architecture Plan
b. A 102- First Floor Architecture Plan
c. A 103- Roof Plan
d. S 101- Ground Floor Structural Plan
e. S 102- First Floor Structural Plan
f. S 103- Roof Framing Plan
g. A-201- North-South Elevations
h. A-202- East-West Elevations

Add additional sheets based on the sections created in your Revit file

AIM :

To create multiple sheets and produce the drawings in the sheet from the given drawing list

INTRODUCTION :

Each view can be placed on one sheet only. To add a particular view to multiple sheets in a project, create duplicate views, and place each one on a different sheet. To quickly open and identify the sheet a view is placed on, in the Project Browser, right-click the view name, and click Open Sheet

PROCEDURE :

STEP 1:

• First we produce the Ground floor archietectural plan in the sheet template A -101 as shown in the below fig,

STEP 2:

• Next we produce the First floor archietectural plan in the sheet template A -102 as shown in the below fig,

STEP 3:

• Next we produce the Roof plan in the sheet template A -103 as shown in the below fig,

STEP 4:

• Next we produce the Ground floor structural plan in the sheet template S -101 as shown in the below fig,

STEP 5:

• Next we produce the First floor structural plan in the sheet template S -102 as shown in the below fig,

STEP 6:

• Next we produce the Roof framing plan in the sheet template S -103 as shown in the below fig,

STEP 7:

• Next we produce the North - South elevation view in the sheet template A -201 as shown in the below fig,

STEP 8:

• Next we produce the East - West elevation view in the sheet template A -202 as shown in the below fig,

RESULTS :

Create multiple sheets and produced the drawings in the sheets from the given drawing list,

10) Create a camera-specific view or a 3D view in each room ( living, dining, bedroom). Based on the views create a new set of sheets starting A-501 (you can add as many sheets after, 502, 503.. n)to place the 3D view images. Produce the sheets as a part of project drafting.

AIM :

To create a camera specific view or a 3D view in a living room , dining room, bed room in the sheets,

INTRODUCTION :

Click on the View tab, Create panel, 3D View drop-down triangle, and click Camera. Click in the Plan view to place the Camera. Move the mouse away and click to select a target location. This will be the point that the camera will be looking toward

PROCEDURE :

STEP 1:

• First we take the sheet name as A-501,
• Next go to floor plan place the camera in bed room , and camera view in the bedroom as shown below,

STEP 2:

• First we take the sheet name as A-502,
• Next go to floor plan place the camera in kitchen room , and camera view in the kitchenroom as shown below,

STEP 3:

• First we take the sheet name as A-503,
• Next go to floor plan place the camera in living room , and camera view in the livingroom as shown below,

RESULTS :

Created a camera specific view or 3D view in the bedroom , dining room , loving room in the sheets seperately .