3D Creation of Ceiling, Roof, Architectural plan, Structural plan, Sectional view, Elevation view and Camera specific view for a house plan using REVIT
AIM:-To model a ceiling from the architecture tab above the walls at the first floor level.
INTRODUCTION:-
- The creation of ceilings within Revit is a very similar process to that of floors and roofs-mie you can let Revit do most of the work and "guess"where you want the boundries to be or you can enter "Sketch mode" and literally sketch out the boundary of the ceiling yourself.
- The main thing to remember is to be in the correct Ceilling plan View before you start.Revit"will"let you place Ceillings in floor plan Views,but i would not advise this as you cannot readly see what you have created.
PROCEDURE:-
Step:-
- First we open the revit software,and select the ceilling option from the architecture toolbar.
Step:-
- After selecting the ceilling option,then select the each room one by one.
- Then the ceilling will be created,as shown in the below figure.
Step:-3
- Here we can theceilling in the three dimentional View as shown in the below figure.
RESULT:-
- The ceilling has been modeled successfully from the architecture tab above the walls at the First-Floor level.
2.
AIM:-
To model a roof above the ceilling by selecting the footprints of the ceilling.
INTRODUCTION:-
- Roof covering of the tab of a building,serving to project against rain,snow,sunlight wind,and extremes of tempreture.
- Roof have been constructed in a wide variety of forms flat,pitched,vaulted,domed ,or in combinations as dictated by technical,economic,or aesthetic considerations.The earliest roofs constructed by man were probably thatched roofs that were made of straw,leaves ,branches ,or needs;they were usally set at a slope,or pitch,so that rainfall could drain off them.
- Conical thatched roofs are a good example of this type and are still widely used in the rural areas of africa and elsewhere.
- Thicker branches and timbers eventually came to be used to span a roof,with clay or some other relatively impermeable substance pressed intonthe interstics between them.
- Gabled and flat roofs were possible with these materials.With the invention of brick and cut stone for building,the basic roof forms of the dome and vault appeared.
PROCEDURE:-
STEP:-1
- Open the architecture toolbars, and select the roofs by footprint option as shown in the below figure.
Step:-2
- Next we select the roof and adjust the roof to 10 degrees by selecting it,as shown in the figure.
STEP:-3
- The roof has been created,as dshown below.
RESULT:-
- The roof has been created successfully to the model in the revit in detailed manner.
3.
AIM:-
To create a plan views for ground floor level and first floor level including all the walls,floors and components.
And to separate them to achitecture and structural plans.
INTRODUCTION:-
- The structural plan views is the default view when you start a new project.
- Most project include at least one structural plan.New structural plan views are created automatically as you add new levels to your project.You can create multiple structural plan view types.
- The floor plan view is the default view in a new architectural project.
- Most project include at least one floor plan.
- Floor plan views created automatically as you add new levels to your project.
PROCEDURE:-
Step:-1
- First we draw the architectural plans of first floor and second floor as shown below.
Step:-2
- Next we draw the architectural plans of the first floor and second floor as shown below.
RESULT:-
- Created plan views for ground floor level and first floor level including all the walls,floors,and components.
- And separated them to achitecture and structure plans.
4.AIM:-
To add dimentions to all the walls and floors with reference to the longitudinal and transverse grids created in the project file.
INTRODUCTION:-
- The structure plan view is the default view when you start a new project using a structural tamplate.
- Most projects include at least one structural plan.New structural plan view are created automatically as you add new levels to your project.You can create multiple structural plan view type.
- The floor plan view is the default view in a new architectural project.Most projects include at least one floor plan.
- Floor plan views are created automatically as you add new levels to your project.
PROCEDURE:-
step:-1
- Here we drawn the longitudinal and transverse grides to the architectural floor plans as shown beliow.
- And add the dimentions to the architectural plans as shown below.
Step:-2
- Next we draw a longitudinal and transverse grids to the structural floor plans as shown below.
- And add the dimensions to the structural plans as shown below.
RESULT:-
- The dimensions are added to the structural floor plans and the architectural floor plans.
- And the longitudinal and transverse grides are also created in the project file.
5.AIM:-
To create a sheet template from the view tab and adjust the parameters on the sheet to add appropriate views.
INTRODUCTION:-
- Create views on a project template before you start building the model to streamline the project documentation process.
- When creating a project template, you can include sheets in a template.start with a blank project file , and create the standard views and levels that each project should include .
- Leave the views empty,but assign standard nemes to them.To create a standard set of construction.
- Add views to the sheets,using the desired titel blocks.
- Add views to the sheets ,using the desired viewport templates and view titel types.
- Then save the empty project as a project template,all of the views and sheets are already created and listed in the project Browser.
- As you start to draw the building model in the project views ,the views on the sheets update automatically.
- This technique streamlines the project documentation process and maintains organizational standards.
PROCEDURE:-
Step:-1
- First we click on the sheet option from the view toolbar, as shown below.
- After clicking the sheet,then new tab will be visible on the screen.
- In that new tab we select the A1 metric,then the sheet template we be displayed.
Step:-2
- In the sheert template we insert the first floor plan and second floor plan separately as shown below.
- Next edit the project name and the sheet number as shown in the berlow figures.
g
RESULT:-
- Created a new sheet template from the view tab and asdjusted the parameters on the sheet for adding appropriate views.
6.AIM:-
To create the elevation views, looking at your building from east,North,South and West using the elevation tab.
INTRODUCTION:-
- An elevation is a View of a building seen from one side, a flat representaion of one view.
- This is the most common view userd to describe the external appearance of a building.
- Each elevation is labelled in relation to the campass direction it faces,e.g. looking toward the north you would be seeing the southern elevation of the building.
PROCEDURE:-
Step:-1
- First we click on the elevation option from the view toolbar,as shown below.
Step:-2
- Next the elevation from the east will be visible,as shown below.
Step:-3
- Next the elevation from the south will be visible on the screen,as shown below
Step:-4 - Next the elevation from the North will be visible on the screen,as shown below.
Step:-5
- Next the elevation from the North will be visible on the screen,as shown below.
7.AIM:-
To produce section cut through each room either cutting across longitudinally or in a transverse direction.
INTRODUCTION:-
- Sectional views reveal hidden details in a mechanical drawing.
- These views assume that a cutting plane has removed portionds of the object represented by the drawing,displaying the appropriate section of the interior.
- Sectional views are used in engineering and architectural drawings.
- They help civil engineers,architectects,and airplane designers communicate their ideas to their peers.
PROCEDURE:-
Step:1
- First we click on the cection option from the view toolbar, as shown below.
- Next we produce the section view of the bed room as shown in the below figure.
Step:-2
- Next we produce the section view of the toilet room as shown in the below figure.
Step:-3
- Next we produce the section view of the kitchen room as shown in the below figure.
Step:-4
- Next we produce the section view of the living room as shown in the below figure.
RESULT:-
- Created the section views of a model in the revit in detailed manner.
8.AIM:-
To classify the views,plan Views ,Section Views,and elevatin views to either Design or Documentation category using Properties browser.
INTRODUCTION:-
- The structural plan view is the default view when you start a new project using a structural template.
- Most projects include at least one structural plan.New structural plan views are created automatically as youb add new levels to your project.You can create multiple structural plan view types.
- The floor plan view is the default view in a new architectural project.Most projects include at least one floor plan.
- Floor plan views are created automatically as you add new levels to your project.
- Sectional views reveal hidden details in a mechanical drawing.
- These views assume that a cutting plane has removed portions of the object represented by the drawing,displaying the appropriate section of the interior.
- Sectional views are used in engineering and architectural drawings.
- They help civil engineers ,architects,amd airplane designers communicate their ideas to their peers.
- An elevation is a view of building seen from one side , a flat representation of one view.
- This is the most common view used to describe the external appearance of a building .
- Each elevation is labelled in relation to the campass direction it faces,e.g. looking toward the north you would be seeing the southern elevation of the building.
PROCEDURE:-
Step:-1
- First we open the project browser,the views,section Views,and Elevation Views are visible in that project browser as shown below.
- Next we insert these plans one by one in the sheets separately.
STEP:-2
- First we insert the front elevation in the sheet template,as shown in the below figure.
STEP:-3
- Next we insert the left side elevation in the sheet template,as shown in the below figure.
STEP:-4
- Next we insert the right side elevation in the sheet template,as shown in the below figure.
STEP:-5
- Next we insert the back side elevation in the sheet template,as shown in the below figure.
STEP:-6
- Next we insert the ground floor plan in the sheet template,as shown in the below figure.
STEP:-7
- Next we insert the first floor plan in the sheert template,as shown in the below figure.
STEP:-8
- Next we insert the section -1 in the sheet template,as shown in the below figure.
STEP:-9
- Next we insert the section-2 in the sheet template,as shown in the below figure.
STEP:-10
- Next we insert the section-1 in the sheet template,as shown in the below figure.
RESULT:-
- Views,Plan Views,Section Views and Elevation Views are classified to Design category using Properties browser.
9.AIM:-
- To create a multiple sheets and produce the drawings in the sheets,from the given Drawing list.
INTRODUCTION:-
- Create Views on a project template before you start building the model to streamline the project documentation process.
- When creating a project template,you can include sheets in the template.Start with a blank project file,and create a standard views and levels that each project should include.
- Leave the views empty ,but assign standard names to them,.To create a standard set of construction documents,create sheets using the desired titel blocks.
- Add views to the sheets ,using the desired viewport templates and View titel types.
- Then save the empty project as a project template.
- When you create a project using this project template ,all of the Views and sheets are already created and listed in the Project Browser.
- As you start to draw the building model in the project views,the views on the sheets update automatically.
- This technique Streamlines the project documentation process and maintains organizational standards.
PROCEDURE:-
Step:-1
- First we produce the Ground floor architectural plan in the sheet template A-101,as shown in the below figure.
Step:-2
- Next we produce the first floor architectural plan in the sheet template A-102,as shown in the below figure.
Step:-3
- Next we produce the roof plan in the sheet template A-103,as shown in the below figure.
Step:-4
- Next we produce the ground floor structural plan in the sheet template s-101,as shown in the below figure.
Step:-5
- Next we procedure the first floor structural plan in the sheet template s-102,as shown in the below figure.
Step:-6
- Next we produce the roof framing plan in the sheet template s-103,as shown in the below figure.
Step:-7
- Next we produce the north and South elevation views in the sheet template A-201,as shown in the below figure.
Step:-8
- Next we produce the East and West elevation views in the sheet template A-202,as shown in the below figure.
RESULT:-
- Create the multiple sheets and produced the drawing in the sheets,from the given drawing list.
10.
AIM:-To create a camera -specific views or a 3D view in living room,dining room and bedroom in the sheets separately.
INTRODUCTION:-
- Camera Views are really useful in Revit.
- They us to view what we would actually see if we were standing at any given location in our design.
- This an be invaluable for both understanding and communicating the nature of a space before we go to the expensive lengths of actually constructing it for real.
PROCEDURE:-
Step:-1
- First we take the sheet an d name it a A-501.
- Next go to the floor plan and place the camera in the bed room,and the camera view of bed room will be shown below.
Step:-2
- Next we take the sheet and name it as A-502.
- Next go to the floor plan and place the camera in the kitchen room will be shown below.
Step:-3
- Next we take the sheet and name it as A-503.
- Next go to the floor plan and place the camera in the Living room ,and the camera view of living room will be shown below.
RESULT:-
- Createda camera-specific view or a 3D view in living room,dining room and bed room in the sheets separatly.