3D Creation of Ceiling, Roof, Architectural plan, Structural plan, Sectional view, Elevation view and Camera specific view for a house plan using REVIT

1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level AIM:  To model a Ceiling from the architecture tab above the walls at the first-floor level. INTRODUCTION: The creation of Ceilings within Revit is a very similar…

1). From the file menu, create a new project (Structural / Architectural / Courses > Construction template) and name the project appropriately. AIM: To create the new project(structural/Architectural/Construction n template) of the project appropriately. and name INTRODUCTION OF REVIT.: Revit architecture is designed…

PROJECT- 2    AIM OF THE PROJECT- Creating a 3D rendered model for a Residential Building in AutoCad.    INTRODUCTION- COMMANDS USED FOR DRAWING THE 3D RENDERED VIEW OF BUILDING ARE AS FOLLOWS.    Extrude- Location: Draw > Modeling > Extrude    This AutoCAD 3D Extrude command…

AIM: To create a 3D isometric view of the given building with plan and elevation.    INTRODUCTION:    An isometric drawing is a 3D representation of an object, room, building or design on a 2D surface.    One of the defining characteristics of an isometric drawing, compared to other types of 3D representation, is that…

1.AIM    To create a 3D Furniture element using the various commands in Auto CAD.    INTRODUCTION BY 3D VIEW    The process of creating a mathematical representation of any surface of an object in three dimensions by using special software.    A 3D model can even be represented as a two-dimensional image by using the 3D…

Create a layout of the Plan and Section A of the project in Challenges 7, using the template TutorialmArch.dwt in a scale as given in the Figure. Use the MV command to create the viewport of the size as shown in Figure. Also, use ATTEDIT command to edit the information in the title block. Use Al size for the layout. Take…

Aim: To Create the Kitchen Layout and to Also, use proper dimension techniques to dimension the kitchen layout. Also, insert text wherever required.    All dimensions are in mm.    Procedure:    step 1:    units are set to mm    limits and limax are also set   …

    AIM:  To Create Customl_titleblock and Custom2_titleblock using Attributes and block command from Autocad software.    PROCEDURE:  Step 1 (custom1_tittleblock)    In the command prompt type L to draw the lines    In ribbon tab > Annotate > Mtline (to draft the…

Aim: To draw Architectural drawing of a residential building: Plan of a residential building. Elevation of a residential building. Section of a residential building. Structural drawing: Column plan layout of the building. Footing plan layout of the building. Beam plan layout of the building. Commands used: Line, Offset,…

CHALLENGE 7 AIM-TO DRAW PLAN ELEVATION AND SECTION OF THE HOUSE IN AUTO CAD. INTRODUCTION- Commands used for drawing the plans and drawings below are as follows 1. Line: Draw lines in AutoCAD 2. Polygon: Draws polygons with three or more sides 3. Rectangle: Used to draw rectangles Circle: Command used to draw circles Ellipse:…

AIM: To draw the elevation and details of a wardrobe as shown in the figure. After sketching, you need to provide the dimensions and text with the use of layers. PROCEDURE: STEP 1: • Units are set to mm • Limits and limax are also set Zoom command is also used STEP 2: • In the command line type rec >…

Create a column schedule as shown in figure INTRODUCTION 1.Column C1 is provided with 4 bars of 20 mm dia. and 6 bars of 12 mm dia. The 12 mm dia bars are marked with 'a'. 2. Column C1a and Column C3 are provided with 12 bars of 16 mm dia bars. 3. Column C2 is provided with 8 bars of 20 mm dia and 4 bars of 12 mm dia.…

Aim: To draw the layout of a residence plan. Commands used: XL-V OR XL-H. Offset. Fillet. Extend. Trim. Procedure: First create a new AutoCAD file with imperial settings. Make sure that in units the type is "Engineering" (as the dimension is in feet and inches) and also set the precision. Set the limits with command "LIMITS"…

Aim: to draw the given sketches in AutoCAD Procedure: Open new file and set decimal and precisions to 0.00 Command line: from random point draw 3.00m line and @ 2.12<45, @2.83<135 then 2m line and close Command offset: 3m line to 1m and 2.5m Command circle: from midpoint of 3m line at 2.5m and 1m draw a circle of…

Cross section of loading bearing wall over spread footing. Aim: To draw cress section of wall over footing Commands used: Line Rectangle Trim Procedure: Step-1: Create rectangle by typing “rec” in command box Specify the 1st corner point Specify the length as 0.9 units Specify width as 0.25 Step-2: create another…

To Create the geometries from P1 to P2 using all the coordinates system methods. Absolute coordinate system Relative coordinate system Polar coordinate system   Click on AutoCad on the desktop and open it Click on new Set the units and limits Use line command to start with the drawing Using absolute coordinate systems:…

Sketching the G+1 floor residential plan according to Vaastu shastra and load calculation acting on the building with required drawing   Required drawings: Centre line drawing Footing and column layout with reinforcement details Column schedule with reinforcement details Plinth beam layout with reinforcement details…

Stipulations for Mix Design Concrete Grade designation: M 35 Type of cement: OPC 53 grade confirming to IS 8112 Maximum nominal size of aggregate: 20 mm Minimum cement content: 340 kg/m3 Maximum water-cement ratio: 0.45 Workability: 50-100 mm (slump) Exposure condition: Very Severe (for reinforced concrete) Method…