Menu
Nidhin Kakkanattu
M.Tech Heat Power
Skills Acquired at Skill-Lync :
- CFD
- NUMERICAL-ANALYSIS
- MATLAB
- OPENFOAM
- ANSYS-FLUENT
Introduction
12 Projects
Block Mesh Drill Down Challenge
Abstract In this project, the analysis of transient solver for incompressible, laminar flow of Newtonian fluids is performed by OpenFoam software tool. An initial mathematical analysis on Reynolds number is calculated to figure out the appropriate CFD codes to be used for the problem. Openform case file is manipulated…
28 Apr 2019 09:10 AM IST
Simulation of a 1D Super-sonic nozzle flow simulation using MacCormack Method
Abstract Converging -diverging nozzle is analysed to find the out the thermodynamic properties of the fluid flowing through it. The analysis is carried out by MacCormack method to obtain the final solution. Both conservating, as well as non-conservative governing equations, are used and the comparison of the results obtained…
21 Sep 2018 06:24 AM IST
Fluid flow simulation through a pipe by using OpenFOAM (Part 2)
Introduction The comparison between the wedge, symmetry boundary conditions in OpenFOAM is studied and discussed in this section. The pipe flow with wedge angle 4 degrees is performed in the part1 and the simulation by changing the wedge boundary to symmetry is performed in this section. IcoFoam solver and all solution…
06 Jul 2019 06:51 AM IST
Fluid flow simulation through a pipe by using OpenFOAM (Part 1)
Abstract In this project fluid flow analysis through a pipe is studied and explained. The analysis is performed by the OpenFOAM software tool. Water is taken as fluid and the condition is laminar. Hagen–Poiseuille equation is used to find the pressure drop in the pipe. The result obtained from OpenFOAM is compared…
06 Jul 2019 06:50 AM IST
Steady Vs Unsteady laminar flow over a cylinder
Introduction When a fluid flows over a cylindrical surface different flow pattern appears in the laminar flow depending upon the Reynolds number. Different flow patterns show in the image below. Re<1 The flow is streamlined and symmetrical about the horizontal and vertical axis. The flow covers the entire cylinder and…
16 Nov 2019 12:31 AM IST
Solving the steady and unsteady 2D heat conduction problem
Abstract Temperature plot on a 2D plate is performed by using MATLAB. Steady state condition, as well as the unsteady state, is described. The governing equations are implemented and Jacobi, Gauss-Seidel and SOR iteration process is used to converging the final results. Problem description A 2D pyrolytic…
19 Sep 2018 08:57 PM IST
CFD analysis of flow through Tee junction by using Ansys fluent
Abstract This project involves the steady, incompressible analysis of the flow of air through Tee junction. Ansys fluent software is used to simulate the flow of air. The effect of length of the pipe after the junction and also the cold air inlet velocity is varied to investigate the effectiveness of the Tee junction.…
12 Oct 2020 01:22 PM IST
Week 2 - Flow over a Cylinder.
31 Jul 2022 06:32 AM IST
Week 3 - External flow simulation over an Ahmed body.
24 Oct 2022 11:01 AM IST
Week 4 - CHT Analysis on Exhaust port
12 Nov 2022 10:10 AM IST
Week 4 - CHT Analysis on Exhaust port
14 Nov 2022 08:38 AM IST
Week 5 - Rayleigh Taylor Instability
https://www.youtube.com/watch?v=05x69eojLQA https://www.youtube.com/watch?v=xA1GVCVU5Y4&t=73s https://www.youtube.com/watch?v=lVDi3vBv0Fg
16 Dec 2022 09:10 PM IST
1 Course Certificates
1 Workshop Certificates
Academic Qualification
M.Tech
Visvesvaraya National Institute Of Technology
01 Jul 2011 - 31 May 2013
B.Tech
AWH Engineering College
01 Aug 2005 - 31 May 2009
12th
St. Antony's Higher Secondary School
01 Jul 2003 - 30 Apr 2005
10th
Government Vocational Higher Secondary School cherp
01 May 2002 - 30 Apr 2003
Here are the courses that I have enrolled
Similar Profiles
Ladder of success cannot be climbed with hands in pocket.
The Future in Motion
Give more than what you get you will get more than what you gave
Avid learner