Full course · free on YouTube · 2 h 9 min

Build an IoT application with ESP32: free, 2.2 hours

One live workshop recording of about 2 hours 9 minutes, published in February 2023. It opens with IoT concepts and the ESP8266 and ESP32 boards, then builds circuits one at a time in an online simulator and ends with an MQTT demo.

24 chapters · published 21 Feb 2023 · 4,415 views as of 19 Nov 2026 · by Skill-Lync

Free. We ask for your name and phone once before it plays here · or watch on YouTube ↗

Who is this course for?

Engineering students and beginners who want a first hands-on IoT project with an ESP32, using only a browser simulator.

What will you learn?

  • Explain IoT nodes, gateways, the cloud and peer-to-peer connections
  • Tell the ESP8266 and ESP32 apart and say what a system on chip adds over a microcontroller
  • Wire an LED, relay and push button to ESP32 pins and drive them with pinMode, digitalWrite and digitalRead
  • Read an LDR through the ADC with analogRead and print values on the serial monitor
  • Measure distance with an HC-SR04 ultrasonic sensor and set a servo angle
  • Switch an ESP32 LED on and off over MQTT using a broker and the PubSubClient library

What does each part of the course cover?

7 sections, in watching order. Click a timestamp to jump the player there. The video description has no chapter list, so these chapters and timestamps were written from the video itself.

  1. 0:0015 min · 6 chapters

    What IoT is, why it took off, and where it is used

    The speaker defines IoT as embedded devices with sensors that exchange data with the cloud, lists what made it practical (cheap sensors, mobile data, cloud platforms, analytics), then draws centralised and peer-to-peer architectures and the node, application and interface framework, with use cases in cities, industry, health and logistics.

    Chapters
    • 0:00Welcome, workshop goals and session plan
    • 1:27What the Internet of Things is
    • 4:40What made IoT possible
    • 7:40IoT architectures: nodes, gateway, cloud and peer-to-peer
    • 9:37IoT framework: node, IoT application and graphical interface
    • 11:43IoT use cases by sector
  2. 14:4718 min · 5 chapters

    ESP8266 and ESP32 hardware, with live questions

    Why the ESP8266 and ESP32 suit first IoT projects: a system on chip with Wi-Fi, GPIO, ADC, PWM and serial peripherals. Block diagrams of both, a comparison table, and answers to chat questions on SoC versus microcontroller, IoT versus embedded systems and the ThingSpeak dashboard.

    Chapters
    • 14:47Hardware for IoT: ESP8266 and ESP32 as system-on-chip boards
    • 18:47ESP8266 block diagram and pins
    • 20:36ESP32 block diagram and extra features
    • 22:02Questions: SoC vs microcontroller, IoT vs embedded, ThingSpeak
    • 31:24ESP8266 and ESP32 compared
  3. 32:4313 min · 3 chapters

    Online simulator, first blinking LED and Arduino APIs

    A walk through the free browser simulator: the sketch, diagram.json and library manager, and the parts menu. An LED and resistor are wired to pin 2, a setup and loop sketch blinks it every second, and the common Arduino calls (pinMode, digitalWrite, analogRead, Serial, servo) are listed.

    Chapters
    • 32:43Tour of the online ESP32 simulator (Wokwi)
    • 35:04First circuit: blinking an LED on pin 2
    • 43:07Arduino APIs available on the ESP32
  4. 45:5922 min · 3 chapters

    Digital outputs and inputs: LEDs, relay and push button

    LED polarity and the current-limiting resistor, then practice exercises (a running LED and a 4-bit counter). Relay types and the normally open and normally closed contacts, a relay on pin 26 switching an LED, and a push button read with digitalRead to toggle an LED, with a delay added.

    Chapters
    • 45:59LED circuit basics and practice exercises (running LED, 4-bit counter)
    • 49:03Relay and LED circuit
    • 56:26Push button reading an LED on and off
  5. 1:07:5426 min · 2 chapters

    Analog input: ADC theory and an LDR light sensor

    Sensor, signal conditioning, sampling, quantisation and encoding, with the Nyquist sampling idea. Then an LDR wired to an analog pin with a threshold of 800 and readings on the serial monitor. When the external LED stayed off, the speaker switched to the onboard LED on pin 2.

    Chapters
    • 1:07:54How analog-to-digital conversion works
    • 1:17:28LDR light sensor with analogRead and the serial monitor
  6. 1:33:3819 min · 2 chapters

    Ultrasonic distance sensor and servo motor

    How the HC-SR04 measures distance from the echo delay, halved because the sound travels out and back, and its four pins and pulseIn. Then how a servo holds a commanded position using potentiometer feedback, its three pins, and an ESP32 servo sketch sweeping from 0 to 180 degrees.

    Chapters
    • 1:33:38Ultrasonic distance sensor (HC-SR04)
    • 1:41:39Servo motor position control
  7. 1:52:1317 min · 3 chapters

    MQTT and an ESP32 controlled from a web client

    What MQTT is: a lightweight publish and subscribe protocol with a broker between devices and cloud. In the demo the ESP32 joins Wi-Fi, subscribes to an LED topic through the PubSubClient library, and the HiveMQ web client publishes on and off messages that switch the LED.

    Chapters
    • 1:52:13MQTT: publish, subscribe and the broker
    • 1:58:13MQTT demo: switching the ESP32 LED from a HiveMQ web client
    • 2:08:30Closing remarks and sharing the code

Is the Build an IoT Application in 2 Hours course really free?

Yes. All 2 h 9 min of it is free on Skill-Lync's YouTube channel, with no payment. To watch it on this page with the chapter guide, leave your name and phone number once; you can also watch it directly on YouTube. It was published on 21 Feb 2023 and had 4,415 views as of 19 Nov 2026. This page adds the chapter guide, a study plan and what to learn next.

How long does the Build an IoT Application in 2 Hours course take to finish?

The video runs 2 h 9 min across 24 chapters. At one hour a day that is about 3 days; plan roughly twice that if you practise each exercise as you go. The longest section is "Analog input: ADC theory and an LDR light sensor" (26 min), so give it its own days.

Does the free ESP32 course come with a certificate?

The video description has a "claim your certificate" link, which now opens this page. To ask about a certificate for this course, leave your name and phone number in the form below and a Skill-Lync counsellor will call you back. The paid Skill-Lync courses linked here include a certificate along with mentor-reviewed projects.

What should I learn after this course?

The next step is Developing IoT Applications (free lessons), then Developing IoT Applications (₹40,000), then PG Program in Embedded Systems for EV Applications (₹2,75,000). The free course teaches the concepts; the paid Skill-Lync courses add graded projects, mentor feedback and, in the PG programs, placement support.

Do I need an ESP32 board to follow the IoT workshop?

No. The speaker builds every circuit in a free online simulator that runs in the browser, so the circuits and code can be tried at zero cost. The speaker adds that the Arduino IDE is not needed inside the simulator, and that the same circuits can be built on a breadboard with real hardware.

How does an ultrasonic sensor measure distance?

The sensor sends a short burst of 40 kHz sound after a trigger pulse, then times the echo that returns from the obstacle. Distance is the time taken multiplied by the speed of sound, divided by two, because the sound travels to the obstacle and back. The code reads the echo time with pulseIn.

How does the MQTT demo turn an LED on and off?

The ESP32 connects to Wi-Fi and subscribes to a topic on a public broker. In the HiveMQ web client, the speaker publishes the message on or off to that topic, and the callback in the ESP32 sketch sets the LED pin high or low. The simulated LED follows each message.

Last updated 19 Nov 2026 · Course length, chapters, views and dates from the YouTube video on 19 Nov 2026 · Grow by Skill-Lync: free lessons from every course

Finished the course?

Ask about the certificate or your next course.

Leave your name and phone number. A Skill-Lync counsellor calls you back within one working day about the certificate for Build an IoT Application in 2 Hours and the course that fits where you want to work.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Free full course · Skill-Lync

Start watching

Free, no payment. Leave your name and phone once and the whole Build an IoT Application in 2 Hours course plays here, with every free lesson on Grow. A Skill-Lync counsellor may call you about the certificate or your next course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.