Full course · free on YouTube · 1 h 6 min

Firmware development: free introduction, 66 minutes

A single 66-minute recorded workshop from Skill-Lync, taught with slides. It moves from embedded system basics and firmware versus software to C storage classes, startup code, embedded C, communication protocols and the SPI protocol, and ends with career options.

14 chapters · published 19 Aug 2021 · 31,441 views as of 19 Nov 2026 · by Skill-Lync

Free. We ask for your name and phone once before it plays here · or watch on YouTube ↗

Who is this course for?

Electrical, electronics and computer engineering students who know basic C and want to see what firmware development involves before choosing a career in embedded systems.

What will you learn?

  • Tell a microprocessor, a microcontroller and an SoC apart by what sits inside the chip
  • Explain how firmware differs from software, and what bare metal means
  • Separate a firmware driver, which configures peripheral registers, from the application that uses it
  • Compare the four C storage classes by storage, scope, life and default value, and say what volatile does
  • Follow a startup sequence from reset to main, including filling .bss with zeros
  • Describe the SPI lines (clock, MOSI, MISO, chip select) and what clock polarity and phase set

What does each part of the course cover?

7 sections, in watching order. Click a timestamp to jump the player there. The video description has no chapter list, so these chapters and timestamps were written from the video itself.

  1. 0:008 min · 2 chapters

    Agenda and what an embedded system is

    The speaker lists the topics for the session, then defines a system and an embedded system as software and hardware built for one specific task. Remote controls, air conditioners, refrigerators and washing machines are contrasted with a laptop, and the speaker lists low cost, stability and low power as typical characteristics.

    Chapters
    • 0:00Agenda and what the workshop covers
    • 3:03What an embedded system is
  2. 7:5413 min · 1 chapter

    Microprocessor, microcontroller and SoC

    A microprocessor holds only a CPU and needs external RAM, ROM, timers and ports on buses, as in a desktop. A microcontroller packs the core, memory and peripheral controllers such as I2C, SPI and UART into one chip. An SoC combines powerful parts like a CPU, DSP and GPU on one chip, and a comparison table follows.

    Chapters
    • 7:54Microprocessor, microcontroller and SoC
  3. 21:107 min · 2 chapters

    Firmware versus software, drivers versus applications

    Firmware is low-level software kept in ROM or flash on a single-purpose device, often with no operating system, which is why it is called bare metal. A car-and-driver analogy separates the firmware driver, which configures peripheral registers, from the application that calls the driver's APIs, shown with a GPIO example.

    Chapters
    • 21:10Firmware versus software
    • 25:02Firmware drivers versus firmware applications
  4. 28:3915 min · 3 chapters

    C storage classes, memory sections and volatile

    The four C storage classes (auto, register, static, extern) are compared by storage, scope, life and default value, with the code, stack, heap, .data and .bss sections. It covers why register variables cannot be global, how static functions can be reached through a function pointer, and why volatile stops the compiler caching a driver-updated variable.

    Chapters
    • 28:39C storage classes and memory layout
    • 35:42Heap, .data and .bss, and limits on register and static variables
    • 39:26Constant variables, string literals and volatile
  5. 43:314 min · 2 chapters

    Startup code and embedded C versus generic C

    A startup walkthrough shows the linker script naming the entry point, the reset function, copying initialised data and filling .bss with zeros before main is called. The talk then contrasts embedded C with generic C: register and memory mapping, heavy use of pointers and bitwise operators, no printf or scanf, and very limited RAM and ROM.

    Chapters
    • 43:31Startup code walkthrough
    • 45:03Embedded C versus generic C
  6. 47:1215 min · 3 chapters

    Communication protocols and the SPI protocol

    Ethernet, USB, RS-485, RS-232, I2C and SPI are compared by speed, distance and typical use, with I2C and SPI for devices on the same board. SPI is then explained with one master and several slaves, the clock, MOSI, MISO and chip select lines, shift and buffer registers, and clock polarity and phase.

    Chapters
    • 47:12Communication protocols and where each is used
    • 50:07SPI: lines, master and slave, chip select
    • 56:16SPI data transfer, clock polarity and clock phase
  7. 1:01:514 min · 1 chapter

    Career paths and opportunities

    The speaker argues that learning firmware teaches how hardware behaves, which makes Linux device drivers and application work easier. Areas named are IoT, firmware drivers and applications, pre-silicon and post-silicon verification and validation, sensor driver development, and modelling and simulation.

    Chapters
    • 1:01:51Career paths and opportunities in firmware

Is the Introduction to Firmware Development course really free?

Yes. All 1 h 6 min of it is free on Skill-Lync's YouTube channel, with no payment. To watch it on this page with the chapter guide, leave your name and phone number once; you can also watch it directly on YouTube. It was published on 19 Aug 2021 and had 31,441 views as of 19 Nov 2026. This page adds the chapter guide, a study plan and what to learn next.

How long does the Introduction to Firmware Development course take to finish?

The video runs 1 h 6 min across 14 chapters. At one hour a day that is about 2 days; plan roughly twice that if you practise each exercise as you go. The longest section is "C storage classes, memory sections and volatile" (15 min), so give it its own days.

Does the free firmware course come with a certificate?

The video description has a "claim your certificate" link, which now opens this page. To ask about a certificate for this course, leave your name and phone number in the form below and a Skill-Lync counsellor will call you back. The paid Skill-Lync courses linked here include a certificate along with mentor-reviewed projects.

What should I learn after this course?

The next step is Fundamentals of Embedded Systems (free lessons), then Embedded Programming Essentials (₹40,000), then Pre-Graduate Program in Embedded Systems (₹1,50,000). The free course teaches the concepts; the paid Skill-Lync courses add graded projects, mentor feedback and, in the PG programs, placement support.

What is the difference between a microprocessor and a microcontroller?

In the workshop, a microprocessor is an IC with only a CPU, so RAM, ROM, timers and ports must be connected externally, as in a desktop. A microcontroller puts the core, RAM, ROM and peripheral controllers such as I2C, SPI and UART in one package, which suits compact embedded devices. The talk adds that an SoC combines both ideas with more powerful parts.

Do I need to know C before this firmware workshop?

The video does not state prerequisites. The speaker says viewers may already know the C keywords covered, such as storage classes, and wants to go through them in depth. The session is slide-based and covers embedded C ideas and the SPI protocol theory, not a hands-on board demonstration.

Which software or board do I need for this firmware course?

The video does not name an IDE, compiler or development board, and it does not say whether a licence is needed. It is a talk with slides and code snippets: SPI is explained theoretically rather than at code level, and the speaker says the full protocols are covered in the actual course sessions.

Last updated 19 Nov 2026 · Course length, chapters, views and dates from the YouTube video on 19 Nov 2026 · Grow by Skill-Lync: free lessons from every course

Finished the course?

Ask about the certificate or your next course.

Leave your name and phone number. A Skill-Lync counsellor calls you back within one working day about the certificate for Introduction to Firmware Development and the course that fits where you want to work.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Free full course · Skill-Lync

Start watching

Free, no payment. Leave your name and phone once and the whole Introduction to Firmware Development course plays here, with every free lesson on Grow. A Skill-Lync counsellor may call you about the certificate or your next course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.