Lesson finished
Unlock all 45 lessons of Structural Steel Connection DesignFull course ₹40,000 · paid
High Strength Friction Grip Bolts, Slip Factor and Advantages
A free lesson from Skill-Lync's Structural Steel Connection Design course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Week 1 Session 3”
What will you learn in this free Structural Steel Connection Design lesson?
The instructor covers turned and fitted bolt tolerances, then high strength bolts of class 8.8 and 10.9 made by quenching and tempering. The lesson explains friction load transfer, slip factor, surface preparation, galvanizing limits, IS 3757 dimensions and why fewer bolts and smaller gusset plates result.
- Quenching and tempering for bolt strength
- Slip factor and clean contact surfaces
- Why 10.9 bolts avoid hot dip galvanizing
- Fewer bolts and smaller gusset plates
What comes after lesson 3?
Later in Skill-Lync's Structural Steel Connection Design course (paid): lesson 4, Week 1 Session 4; lesson 5, Week 2 Session 1; lesson 6, Week 2 Session 2. The full course has 45 lessons (20 h 36 min of video); see the course overview or its price and syllabus.
Lesson transcript
Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.
Welcome to the next session of First Peek's topic on Introduction to Connections and about the bolted connections. So in last session, what we have seen is about the introduction of bolted connections, how the bolts are being made up of a single rod, and then what is the thread length and the grip length. And also we have seen the necessity of a washer plate, so how this is going to transfer the clamping pressure on the surface of the material to which it is being bolted. And also on the basis of the material it is made up of and the strength of the bolt, it has been classified into ordinary or black bolt or a snug fit or turned and fitted bolts and also high strength friction grip bolts.
And we have been seeing each bolt in detail one by one. First we saw about the black bolts or ordinary bolts, which has a strength of 4.6 grade means. The first part says that 400 has ultimate tensile strength and the second part, 0.6, will be the ratio between the yield strength and ultimate tensile strength. So multiplying the ultimate tensile strength with 0.6 will be getting a yield tensile strength. And also we have seen about what are the most commonly used diameters of the range and that has been represented in the form of M16 or M20 or M24 that way.
And even how much a tensile area is going to be there, which is approximately 0.78 times the shank area of the bolt, which will give you a neck area, which is more critical for tension bolt. And when we reached into the turned and fitted bolts, in turned and fitted bolts are similar to that of black bolts except the fact that it is made up of a hexagonal rod. So that is also made up of the mild steel, which is low carbon steel. And here it has been the less tolerances are applicable and because of which it has been used in the places where it has been a snug bolted or snug tightened.
So coming to the turned and fitted bolts, I would like to add some more points on those bolts in addition to those points which we have seen in the play session. Here the surface of these bolts are carefully prepared and meshed to fit into the hole. As I said, this is having a less tolerances. This exactly fixes or follows the dimensions and size as per the standard and what it is required. So that's the reason that the surface of the bolts has to be carefully prepared and meshed into the bolt holes.
So this also makes sure that it has been snug fitted. It doesn't allow any bearing between the plates. Here the tolerances allowed in this bolt types are about 0.15 mm to 0.5 mm. This 0.15 mm to 0.5 mm is the tolerances that you allow to the bolt from it being manufactured in the fabrication process. For example, you have a bolt length of, say for example, 100 mm, it can be allowed to go for a tolerances or can have a bigger size of 100.5 mm maximum or 100 minus 0.5 mm as a minimum size.
So since the tolerances in the manufacturing process are limited, these bolts are expensive. So these are most commonly used in buildings and all. This theoretically, I will like to emphasize to the listeners about this turned and fitted bolts. And they are used in applications where low tolerances are required and reduces slip of the plates before bolts go into bearing. So as we know that ordinary or black bolts predominantly transfers the forces in the form of bearing. Here, similar to that of black or ordinary bolts, but only thing is like you have a low tolerances and it is snug fitted.
So the slip between the plates are reduced initially so that this slip will cause the bearing of the bolts which in turn transfers the forces reduction. So predominantly the force which the ordinary or black bolts are going to transfer is by bearing. So bearing is the shear between the two surfaces. When these two surfaces undergoes shear, the bolt should not get slipped away on the plates. This will ensure that the force is getting transferred predominantly or the action is happening properly. So in that category, the turned and fitted bolts are used.
So that's all about the turned and fitted bolts. Let's get into the next type, high strength bolts. High strength bolts are prepared from the rods of medium carbon steel. So unlike from the previous cases, both ordinary bolts are fitted bolts which is made up of low carbon steel. Here it is made up of high carbon steel. So high carbon steel means like you have a carbon content more than 0.6.8, which makes the material of the bolts to less ductile. So it will be little bit brittle in nature.
Moreover, the bolt of this property classes 8.8 and 10.9 are widely used in steel construction. Similar to that of what we have seen in the bolt earlier, like for the ordinary bolts. Here also the class has been represented in the form of 8.8, 10.9, that we have seen about 4.6. So this 8.8 also represents the first point, 800 as approximately the ultimate and steel strength. And 0.8 times the 800 will be 640, which will give you the yield strength of the bolt. So most commonly 8.8 gradient, 10.9 can be used widely in steel constructions.
These bolts should conform to IS-3757. So Indian standard 3757 should be referred to have some of the mechanical and physical properties of these bolts to which it can be adhered. Now the manufacturers who manufacture this type of bolts have to adhere with all the specifications mentioned in the code of 3757. Their high strength is achieved by quenching and tempering process of a alloying steel. So this is a medium carbon steel. The medium carbon steel is going to have a more carbon content. The more the carbon content, it is going to be higher strength.
Higher the strength, it is going to have a less ductility. This higher strength is achieved by the manufacturing process called as quenching and tempering. Quenching and tempering is a heat treatment process with which undergoes cooling also consequently so that the high strength is achieved. So one of the other type of increasing the high strength through alloying also. The alloying means like you will be adding some of the alloys like tungsten, benadium or nickel so that the strength of the bolts are increased consequently. So coming to the next point, they are less ductile but stronger than the black bolts.
So it is made up of medium carbon steel which evidently defines so that the material is going to have a stronger than the black bolts and it is going to have a less ductility because of high carbon content. This less ductility will make the failure of the connections brittle as we have discussed earlier also. Unlike the material members like a member of a structure, here the connection is going to be a brittle failure. It does not show any kind of deformation or the kind of abnormalities in the connection point.
Instead it will just crack will come on it and then it gets spilled off from the connection member. So it is going to be a ductile failure. These bolts are tightened until they have very high tensile stresses which is more than two times the ordinary black bolts so that the connection parts are clamped tightly together between the bolts and nut heads. Unlike in ordinary black bolts, here the load transfer happens predominantly by the friction. So in that earlier case we have two plates say for example and you are bolted together.
When this bolts, let me just put a picture a little bit so that you get an idea. So you have two bolts, these are two plates. So this undergoes tension this way, say this is a nut, this is going to be bolt area. So in earlier cases when this is a black bolt, so what happens is like there will be a bearing between the plates. So bearing between the plates will happen here. It will try to move in this category so that the bearing between the plates will predominantly transfer the force between the members.
When that is happening there should not be slip in the bolts. So we have a bolt hole which may be a little bit extra. So this bolt should not be held responsible so that when this bolts slip away, this will consequently reduce the bearing between the plates and the bolts thereby reducing the transfer mechanism of the forces between the members. Now in the next category we have seen about the tight fit of bolt. This will be tightly fitted so that the plates will undergo bearing and the force transfer also predominantly by the bearing.
But the tight fit will ensure that the less tolerances so that the bolt hole is snug fitted without having any excess. to that of the bolt diameter. Here in this category of high strength bolts, you fix this bolt or clamp together tightly between the bolts and knives. So even though you have a bigger hole dia, say for example this is hole dia, even though this is a hole dia in excess to that of the bolt diameter, so this is the bolt diameter. When it is tightly clamped together, there won't be any slip happening between the bolt and then the plate.
So the hole transfer mechanism of the forces will happen predominantly by the friction here. So this entitles the force transfer not happening via bearing or shear. So that is one of the very important load transfer mechanism that you people have to keep in mind. So coming to the next points, the induced initial tension in the bolt is called as proof load or the bolt and the coefficient of the friction between the bolt head and the faying surface is called the slip factor. As we said here the earlier thing also like the tensile stress which will be more than two times that of the ordinary bolts is achieved because of that has been clamped together.
This clamped together has a force so that the initial induced tension in the bolt obtained is called as a proof load of the bolt. So this proof load defines the bolt capacity and also the coefficient of friction between the bolt head that is the head of the bolt and the faying surface. This faying surface is the surface which is the surface which is in contact with that of the bolt head. So say this is a bolt and you have a member, two plates. So this is the faying surface.
So the friction between the bolt head which is this one and then the faying surface is called a slip factor. The slip factor is also important in transferring the forces between the bolt head directly to the member's faces in the form of tensile force. Coming to the next point, the surfaces in contact should be free of mill scale, rust, paint, grease etc. which could prevent the solid contact between the surface and thus lowering the slip factor. The slip factor is nothing but the coefficient of friction.
So here the force transfer is predominantly with the friction. The rust or paint or grease will reduce the friction and alter the friction so that the transfer of forces won't happen by a frictional force predominantly and thus reducing the efficiency of the bolts for which it has been used for connection between the plates. This mill scale is nothing but flaky material. This mill scale is nothing but flaky material that comes out of the surface of the material. So this is mostly happening in the hot roll sections where the process has been done in the milling.
So this mill scale that you would have come across in lot of steel beams or columns that you see in railway stations and all. A part of outer layer comes as tilt of the mill scale. The next one is a rust. A rust as you know that it is going to be the action of atmospheric oxygen on the iron is going to cause a rust. And even the paint that you put on the material which is to prevent the rust or grease so that your bolts are fitted properly will affect the force transfer between the bolts and the members.
So that has to be ensured that these should not be present in the contact where the bolt is done. The next point is bolts of property class 8.8 can be hot dipped galvanized as per IS 1367 part 13. Hot dipped galvanized. Galvanization is a process of dipping in a pond of iron so that you have a rust free surface. It looks like a clean finish silver color which makes the material not undergo rust. So this bolts of this class 8.8 can be hot dipped galvanized adhering to the IS bolt.
Whereas class 10.9 bolt should not be hot dipped galvanized. So this is a high strength bolt 10.91. This is not recommended to undergo any hot tip galvanization process because this may cause a high hydrogen embrittlement. The hydrogen embrittlement is nothing but the hydrogen surface with which it reacts with a bolt and this will reduce the ductility of the bolt. As you know that when you go for a high strength the ductility is getting reduced. This 10.9 bolt category is going to have a higher strength than the 8.8 or 4.6 bolts.
This is already have a lesser ductility. Being it a hot tip galvanized it reacts with the hydrogen in the atmosphere and then this would cause a reduction in the brittleness. That's why it is not recommended for 10.9 bolts to undergo hot dip galvanization. So this can be adhered to the IS 3757 code. Then coming to the dimensions of high strength friction grip bolts as per IS 3757 1985 which are as follows. So you have a M16, M20 and M24 and M30 bolts. Similar to that of the ordinary or black bolts the representations.
Here 16mm defines the diameter of the bolt but 20mm defines the diameter of the bolt. So M means symmetric. So here the diagonal head which is represented as E can be ranging from 10mm, 12.5mm, 15mm and 18.7mm respectively. For the thickness. So this thickness is given in K. The K is said to have 10mm, 12.5mm and 15mm and 18.7mm whereas E which is going to be the head diagonal can be between 29.56mm. You can see that the head is going to have a bigger diameter than the shank diameter which is given in the form of 16mm.
This is going to have a thickness of 10mm, 12.5mm, 15mm and 18.7mm which will ensure surface getting properly fitted with the surface of the material. Next comes the nut thickness. So here in the thread the nut is going to be there. It will be sleeved upon. This nut thickness is ranging from 13mm to 24mm for M16 to M30 bolts respectively. Then we have a washer here. This is a washer. So the washer the outer diameter can be represented in a capital D which can range from 30, 37, 44, 50, 60.
You can see that for a 16 diameter bolt the bolt head is going to have a bigger diameter and the washer is consequently going to have a bigger than the diagonal head. So that you can see it here. I am coming to the next one. The washer thickness. For heavy washer thickness, for transferring heavy load it has to range from 4mm to 5mm. And even the thread length. So this is the thread length. Represented as B. So where up to which the nut can be tightened.
This thread length. If the bolt length is more than 100mm. The thread length can range between 38mm to 56mm. So the bolt length is less than 100mm. Thread length can range from 31mm to 49mm. So that is the range which adheres with IS 3757-1985. To give us specifications of all the high strength bolts ranging from M16 to M30. So all bolts we saw and their grades available in market are shown below. Similar to that of the ordinary or black bolts. So here's to IS 13600 part 3.
Which also defined from ISO standard. International standard organization 8, 9, 8. Specifications of past turns here are given in the grade or classifications. In the form of 3.6, 4.6, 4.8. As we saw that 8.8 bolts and 10.9 bolts are most commonly used here. So here also the first part defines the yield strength approximately. You can see that one here. The first part defines the ultimate tensile strength. So it approximately gives you ultimate tensile strength 300. Which is nearby 330. And 400. Here also you get 420.
Little bit higher than the initial part. The first part will give you approximate estimate of the ultimate tensile strength. Which is rather than FUB or Newton per mm square. Now the second part will give you the ratio between the yield strength and ultimate tensile. So multiplying this ultimate tensile strength with the second part which is 0.6. You will get the yield strength. Now it is very similar to that of the one which we have seen earlier also. So here the elongation percentage. How much elongation it has been allowed is given here.
We can see 25 for 3.6 grade whereas 8 mm elongation is for 12.9. Which again interprets that when we go for higher grade or higher strength bolts. It is going to be more brittle. So more brittle means there is no susceptible to undergo any elongation before failure. So the elongation or the change in length is reduced tremendously. The 3.6 grades and all like it's a low strength. So it will be going to have a high ductility. That's why you have a percentage of elongation of 25 in percentages.
So that is one of the things that can be interpreted from this table. Coming to the advantages high strength friction grip bolts which are as follows. The high strength bolts HFG do not allow any slip between the connected members. Particularly in close tolerance holes thus provided rigid connection. Most of the angles should be placed against the 100 and the 100 and the 100. The 0.12 billion. The 0.12 billion. The D2 B2. It has been tightened stiffly and prominently the force is going to transfer with friction, thus which makes them, there is no slip between the bolts.
It entitles or gives you a sense of rigid connections. Due to the clamping action, load is transferred predominantly with friction only. The bolts are not subjected to shear or bearing. And shear and bearing are the same concept, so here the force transfer is going to happen only with friction. Due to the lesser number of bolts, the size of gusset plates are small. So, this high strength bolts are going to have a higher strength than the ordinary bolts. So, instead, if you wanted to resist the so and so force, instead of providing 10 numbers of black bolts, you may need to provide 6 numbers of high strength bolts.
So, providing the high strength bolts of lesser numbers will ensure you to go with a lesser size of gusset plates. So, this gusset plates reduction also will be helpful predominantly in reduction of the weight of the member so that the overall construction cost can be reduced. Next one is deformation is minimized. So, using the high strength bolts, the allowable deformation that you are going to go forward is being reduced tremendously. As high strength friction grip bolts under working loads are not dependent on resistance from the bearing, holes larger than normal can be provided for ease of erection and avoid lack of it.
So, as I said, like when you wanted to fix a bolt, you need to have a hole. So, call this as a plate. You need to put a hole. This hole diameter should be little bit higher than the bolt diameter. So, when we ensure the higher hole diameter, we can place that bolt inside it because of any fabrication error or tolerances are there so that the bolt is not going into it. This can be avoided. This provision of excess of diameter of hole sometimes will cause a slippage of the bolt.
This slippage of the bolt is generally avoided in high strength bolts, tightening it closely so that it acts like a rigid connection. So, even though the hole diameter is more, this is not going to be giving any problem because the force transfer is not happening via a bearing action. So, this will give you ease of erection and even the lack of fit. Sometimes the bolt won't be fitting into the hole. This can be avoided by provision of bigger diameter of hole which mostly will cause a trouble of slipping of bolt.
That is not happening in high strength bolts because of it being tightened properly and the force has been transferred predominantly in the action of friction. No bearing is happening here. So, these are the advantages of high strength bolts. So, as a quick recap of what we have seen in this session, we have seen about the bolt snug fitted or tight fitted bolts in excess of what points we have seen in earlier session. This will be made up of less tolerances and because of which it is expensive.
Here also the force transfer is going to happen via bearing, but it avoids the slippage of the plate because of which it has been fitted tightly. Coming to the high strength bolts, it is also going to have a property saying 8.8 or 10.9. So, here also the first part refines the ultimidian strength and the second part is going to give a ratio of the yield to ultimidian strength and it has to adhere to IS3757. And this high strength is achieved by the quenching and tempering process which is a process to achieve the high strength by proper heat treatment or alloying of steel by adding some of the alloys like vanadium, nickel or tungsten.
So, this is going to have a less ductile and these are clamped or tightly fitted so that the force going to transfer predominantly by the friction known with the shear. And this friction between the bolt head and trailing surface is called a slip factor. And that should be enough restraint from the mill scale or a rust or paint so that the slip factor will be reduced which is the coefficient of friction will be reduced and there is no proper transfer of forces happening in the form of friction.
And this bolt property class 8.8 adheres to 1367 and 10.9 adheres to 3757. And these are the dimensions that we have given in earlier. So, starting from M16, M20, M24, M30 bolts add here into 3757. It is coming to still more classifying the yield strength and ultimidian strength of the bolts for different classifications from 3.6 to 12.9. And it can be interpreted that the elongation percentage will be getting reduced as and when we go for higher grade of bolts because of which this is all less ductile in nature.
And the advantages of high strength bolts also, we have talked about it. Since it is a clamping action, the force is going to be predominantly by the friction and not by the shear and bearing. And the tolerances of holes will provide a rigid connections. And because of high strength, we will provide less number of bolts and consequently reduce the gusset plate sizes. The gusset plate sizes reduction will enormously reduce the weight of the number and then reduce the overall construction cost. And we provide a bigger diameter hole.
The bigger diameter hole is to ensure there is no lack of fit. And then this bigger, larger diameter of holes will ensure this, as I said, the lack of fit and ease of erections. And this will not ensure the force has been transferred in the form of bearing since it is tightly fitted. And under the working loads, this HSFC bolts are designed. So these are the advantages of the high strength bolts and we have seen much in detail about how this high strength bolts have been called upon.
So with this, I am ending the session. In the next session, we will be seeing about the bolt holes, how we have to give these bolt holes and all. And then about how the force transfer mechanism, high strength friction grip bolts and then even the black bolts or ordinary bolts. Thank you.