← Previous lessonFree lesson 2 of 3 · lesson 2 of 54Next lesson →

Unlock all 54 lessons of Advanced PCB Design Using AltiumFull course ₹40,000 · paid

Price & syllabus
Free lesson · 12 min · no payment

SMT and Through-Hole Basics, and Setting Altium Schematic Grids

A free lesson from Skill-Lync's Advanced PCB Design Using Altium course, on Grow by Skill-Lync · Last updated 16 Nov 2026 · Session: “Week 1 Session 2”

What will you learn in this free Advanced PCB Design Using Altium lesson?

The lesson distinguishes surface mount and through-hole technology, then explains why grid settings must match across symbols. It demonstrates changing the visible grid, snap grid and snap distance to 2.54 mm and 1.27 mm, and shows the wire kinks a wrong grid causes.

  • Surface mount versus through-hole packages
  • Why symbols need the same grid setting
  • Visible grid, snap grid and snap distance in Altium
  • Using 2.54 mm and 1.27 mm grids and measuring distance

What comes after lesson 2?

The next free lesson is lesson 3, “Altium Grid Settings, Workspace and Version Control Commits” (12 min). Later in Skill-Lync's Advanced PCB Design Using Altium course (paid): lesson 4, Week 1 Session 4; lesson 5, Week 2; lesson 6, Week 3 Session 1. The full course has 54 lessons (16 h 55 min of video); see the course overview or its price and syllabus.

Lesson transcript

Machine transcript of the lesson audio (lightly cleaned). Technical terms may contain errors; the video is the reference.

PCB design, basic concept. PCB design classification, SMT, surface mount technology, TH or through-hole technology. SMT and TH can be combined. Example, PCB with surface mount component, for example, it is an IC, and through-hole component, an example, is a connector. Connectors can be a surface mount, but not in every case. What you see on the right-hand side is actually a package called DIP. So this DIP package is in the form of through-hole package. So this is how a through-hole package will be looking. PCB grid settings. Grids, they are required for all design environments. Diamonds of each grid, it can be a centimeter, or it can be an inch, or it can be a millimeters, must be set properly.

Improper settings, improper settings, misalignment, as shown in the image. For example, you see an image on the right-hand side. So these two are different symbols. So one is a resistor, the other one is a BJT. So both the resistors and the BJT should be created with the grid setting, with the same grid setting for both the symbols. If the grid settings are not the same, and when the parts are imported in the schematic, then what we see is a misalignment. The most common grid settings is 1.27 millimeter, or 0.05 inch, or 2.54 millimeter, or 0.1 inch.

So how do we access a grid panel in an Altium schematic? So we need to right-click on the sheet, preferences, and select grid. Let's go to the Altium sheet, and let's see how it actually works. Let's see in detail about what are grids, and how to use grids in Altium. So if you look at the Altium schematic, you've got on the right-hand side properties. So the properties, you can see units as millimeters and mils. So I prefer to use millimeters always, so it is easy to calculate the imperial values.

So what you see is visible grids are 1 millimeter, and snap grids is 1 millimeter, and snap distance is 0.4 millimeter. So basically, we can change all these grid settings value. So if you look at the sheet, so these individual boxes are called grids. So how you can find what is the default value is, if you go to tools, if you go to reports, and if you give measured distance. So if you snap from one point to the other point, so what you see is 10 millimeters.

So this is the current value that has been set, 10 millimeters. It's the same thing from here to here, so which is 10 millimeters. So basically, if you click on one point, you can move point by point. So if you move to one single point, so that is 1 millimeter. So if you move from one point to the other point, that is 1 millimeter. So basically, this is called snap. You're snapping it to the next nearest point. So that is called snap. So snap grid settings are set to 1 millimeters at the moment.

So how we are sure it's set to 1 millimeters. So basically, we can measure by using a settings. If you press G, so you can see the grid settings change to 2.5, 5, and 1 millimeter. Just see the mouse where I'm pointing out. You can see 2.5, 5, and 1 millimeter. If you want to change these settings, just right-click and go to preferences. Under preferences, you've got select grids. Under schematic, select grids. If you can't find in the search bar, type GRID. So you'll get a list of options where the grids are being used.

So under schematic, select grid. Here, you don't have to change anything in MELS unless you are using MELS. So we are using only millimeters. So this is the default value that is used in millimeters. Let's close this one and open the properties side by side. Let's go to preferences. So what we see here is snap grid is 1 millimeter. Snap distance is 0.5. And visible grid is 1 millimeter. So visible grid, snap grid, and snap distance. So likewise, these are default settings by Altium. So we are going to change these settings.

So if I press G once again, can you see the values changing here? If I press G once again, can you see the values changing here? So 1, 5, and 2 millimeters. If you go to preferences, you can see 1, 5, and 2 millimeters. So now we are using the third value. So basically, we are going to change these settings to inches. So 1 inch is 2.54 millimeters. So we are going to change all these values. We are going to use only one value, that is inches.

So snap grid, we are going to change this to 2.54 millimeter. Snap distance is again 2.54 millimeters. And visible grid will be again 2.54. In addition to that, we can use a second value, which is 1.27, which is half of 2.54. So if you need to have a fine or coarse small distance, then we can use these values. So we are going to enable these. We are going to give apply. So once you give apply, just look at the background. It will automatically change. Can you see it?

It's changed. You can give OK. So now we are going to check what is being set. As we know, the grid, if you press G, we can see the values 2.54. It will be 1.27. You can't see the third value, which will be blank, because we haven't enabled it. So 1.27 and 2.54 is what we have enabled. Go to reports, measure distance from one point to the other point, which is 0.5. 25.4, because that is what we have been set. References 2.54, 2.54 snap grid and snap grid and visible grid is 2.54.

So if you want to look at the snap grid, which is 2.54, then you can go to reports, measure distance. From here to the next snap distance is again 2.54. So we have used 10 times of 2.54, which is 25.4 millimeters. The reason why we are using 2.54, which is in terms of inches, is because. So if you look at the data sheet of any of the component, the measurements that you can see is either in terms of millimeters or in terms of inches. So it is always preferable to use inches because in the PCB design also, we are going to use inches.

Right. So we are going to add a component for it. I'm going to show you an example. So what if we use a different snap to grid? What sort of issues we are going to see? If you click panel, if you go to Explorer. I right click component, I place a component. So once I place a component, you can see it actually snaps to the origin, to the plus symbol here. So basically, this is snapped to a correct position. So I'm just going to copy and paste here.

So now I'm going to say. So what is a snap distance? So, for example, if I'm going to put this one apart. Maybe somewhere here. So if you're going to make a connection. So if you need to snap between two points. So as long as the distance between this point and the connection that I'm going to make is 2.54 millimeter distance, it's going to snap. Can you see it's snapping 2.54 millimeter? Because the distance between this point and this point is 2.54. So that is why we are seeing it's snapping to that.

As long as the distance is 2.54 millimeter, it's going to snap. What if the settings are being used in a different value? For example, if you're going to go to preferences and we are going to set set to default. So which is all 1 millimeters, apply, OK. I'm going to delete these. So if you see, it's not snapping. It's not snapping at the right point. Because we have changed the snapping point. So what you're going to do is I'm going to delete and place a new part.

So now you can see it's snapping. So every time if you're going to change a grid, you need to add the part once again. So what happens if we don't use a right snap grid? It will be. So if I'm trying to connect two points using wire, can you see? It won't snap to the right position. It snaps to the 1 millimeter grid. So because that is the grid that we have set, it's just 1 millimeter. So if I snap it here, can you see that small kink here?

So this is not allowed when you're doing a schematic. That is the reason it is all. Preferable to use 2.54 mm. So again, I'm going to show you to change to 2.54 and what, how it works. So delete the whole thing. Go to Preferences and check. It's 2.54. Snap distance, again, 2.54. So visible, it's again, 2.54. And you can set to 1.27, 1.27, 1.27. So you can see on the background, the grid will change. Apply, the grid is changed. Right-click, place. See, it is properly connected. You don't see any kink here. So this is allowed.

So the before method, where I changed the visible grid to 1 mm and where you saw a small kink, the reason that it appeared, it's because this component, when it is created for the first time, so the visible grid, a snap grid is used in terms of inches, which is 2.54 mm. That is why when you change to 1 mm, you saw a small kink. So that is why it is always best to use inches, which is 2.54 mm. So please follow these grid settings, what I have used. It will be really helpful when you're doing a schematic design.

Want the rest of Advanced PCB Design Using Altium?

Get the full course syllabus and fees.

The full course is paid (₹40,000). We'll send the syllabus and call you back within one working day.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Full course · paid

Unlock the full Advanced PCB Design Using Altium course

The remaining 51 lessons, mentor-reviewed projects and a certificate come with the paid course (₹40,000). Leave your details: we'll send the syllabus and fees and call you back.

Get the syllabus and fees

A counsellor calls you back within one working day.

By submitting you agree to our Terms and Privacy Policy.

Grow by Skill-Lync · free lesson

Start watching

Free, no payment. Leave your details once and every free lesson on Grow plays straight away. A Skill-Lync counsellor may call you about the full Advanced PCB Design Using Altium course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.