Engineering Thermodynamics cover
Interactive book · Semester 3-4

Engineering Thermodynamics

Fill an empty tank and watch the air inside get hotter than the line, test a heat engine against Carnot, and see a real gas break away from pv = RT

24 chapters, 24 interactives, few words. Every chapter is mapped to the Anna University, VTU, SPPU, Mumbai University and KTU units it covers: systems and properties, the zeroth law and temperature scales, work and heat, the first law for closed systems, steady flow and filling tanks, the second law, Carnot, irreversibility and entropy, entropy generation and isentropic efficiency, available energy and exergy, steam and its phase change, steam processes and dryness fraction, real gases, gas mixtures, Maxwell relations, the Joule-Thomson effect and the Clausius-Clapeyron equation. Power cycles, nozzles, compressors, refrigeration and psychrometry are in the Thermal Engineering book.

  • AUME3391Engineering Thermodynamics
  • VTUBME304Basic Thermodynamics
  • SPPU202043Engineering Thermodynamics
  • MUMEC305Thermodynamics (Modules 1-4)
  • KTUPCMET403Engineering Thermodynamics

By Skill-Lync · Updated 19 Nov 2026 · 24 chapters · 24 interactives · free, no sign-up

Chapter 1

Systems, control volumes and properties: state, equilibrium and quasi-static processes

Which syllabus covers thisAU ME3391 Unit IVTU BME304 Module 1SPPU 202043 Unit IMU MEC305 Module 1KTU PCMET403 Module 1

What is a system, and what can cross its boundary?

A system is whatever you draw a boundary round; everything else is the surroundings. A closed system (gas in a piston-cylinder) keeps its mass: only heat and work cross, and the boundary can move. An open system, or control volume (an air compressor with its inlet and outlet pipes cut), lets mass cross as well. An isolated system (a sealed, rigid, insulated flask) lets nothing through: no mass, no heat, no work. Choosing the boundary is the first step of every problem, because it decides which energy terms appear in the balance.

Closed, open and isolated systems, what crosses the boundary, and intensive vs extensive properties: interactive loads as you scroll

Which properties are intensive and which are extensive?

Cut a tank of air in two and look at one part. Mass, volume and internal energy split with the cut: they are extensive. Pressure, temperature and density stay the same in both parts: they are intensive. A tank of 0.5 m³ at 2 bar and 300 K holds 1.161 kg; half of it holds 0.581 kg, yet both have v = V/m = 0.4305 m³/kg. Dividing an extensive property by mass gives a specific property (v, u, h), which is intensive and is what tables list.

What fixes the state of a substance, and what is equilibrium?

A state is the set of property values at an instant. For a simple compressible substance two independent intensive properties fix the rest: air at 2 bar and 300 K must have v = 0.4305 m³/kg. Properties describe only that state, never how it was reached. They have a meaning only in equilibrium: no change while the system is isolated, so pressure, temperature and composition are uniform (mechanical, thermal, phase and chemical equilibrium). A gas just after a burst membrane has no single pressure, so it has no state yet.

What is a quasi-static process, and when is a real one close enough?

A quasi-static process is so slow that the system passes through equilibrium states, so the path can be drawn on a p-V diagram. The test is speed. In air at 300 K a pressure wave moves at √(γRT) = 347.2 m/s, and nitrogen molecules at an RMS speed of 516.8 m/s. A piston moving at a few m/s is slow on that scale: the gas evens out its pressure long before the piston moves far. A burst diaphragm or a free expansion is not quasi-static.

Predict, then check

A rigid tank holds air at 2 bar and 300 K. A thin wall is slid in, cutting off 0.1 m³ of the 0.5 m³. What is the pressure in the small part?

Worked examples

Mass, specific volume and a part of a tank · A rigid 0.2 m³ tank of air (ideal gas, R = 0.287 kJ/kg K) at 6 bar and 40 °C. Find the mass, the specific volume and the density, and the mass in a 0.05 m³ region of it.
  1. T = 40 + 273.15 = 313.15 K, p = 600 kPa
  2. m = pV/RT = 600 × 0.2 / (0.287 × 313.15) = 1.3352 kg
  3. v = V/m = 0.1498 m³/kg, ρ = 1/v = 6.676 kg/m³
  4. The 0.05 m³ region is a quarter of the volume at the same p and T: m = 0.3338 kg, with the same v and ρ

Answer: m = 1.335 kg, v = 0.1498 m³/kg, ρ = 6.68 kg/m³; the 0.05 m³ part holds 0.334 kg

How fast are gas molecules? · Nitrogen (M = 28.0134 g/mol) and hydrogen (M = 2.01588 g/mol) at 27 °C; R = 8.314 J/mol K. Find the RMS, mean and most probable speeds.
  1. T = 300.15 K and M in kg/mol: N2 0.0280134, H2 0.00201588
  2. N2: c_rms = √(3RT/M) = 517 m/s, c_mean = √(8RT/πM) = 476.3 m/s, c_mp = √(2RT/M) = 422.1 m/s
  3. H2: 1927, 1776 and 1574 m/s
  4. The ratio is √(28.0134/2.01588) = 3.728: lighter molecules move faster at the same temperature

Answer: N2: 517 (RMS), 476 (mean), 422 m/s (most probable); H2 about 3.73 times faster

Is this compression quasi-static? · Air at 300 K in a cylinder 0.15 m long; the piston moves at 2 m/s. γ = 1.4, R = 287 J/kg K.
  1. Speed of sound c = √(γRT) = √(1.4 × 287 × 300) = 347.2 m/s
  2. A pressure wave crosses the cylinder in 0.15/347.2 = 0.432 ms
  3. The piston needs 0.15/2 = 75 ms for the full length
  4. Ratio 174: the pressure evens out about 174 times during one stroke

Answer: Yes, close to quasi-static: the stroke is about 174 times slower than a pressure wave

Chapter 2

The zeroth law, temperature scales and thermometers

Which syllabus covers thisAU ME3391 Unit IVTU BME304 Module 1SPPU 202043 Unit IMU MEC305 Module 1KTU PCMET403 Module 1

What does the zeroth law say, and why does it make thermometers possible?

If body A is in thermal equilibrium with B, and A is also in equilibrium with C, then B and C are in equilibrium with each other, even if they never touch. That is what lets a thermometer work: A is the thermometer. Put it in contact with B until its reading stops changing, then with C; equal readings mean B and C would exchange no heat. Temperature is the property that is equal for bodies in thermal equilibrium. The law came after the first and second, but logically sits before them, hence zeroth.

How does a constant-volume gas thermometer define temperature?

Seal a bulb of gas at the triple point of water, where it reads p_tp, then put it in the bath and read p at the same volume: T = 273.16 K × p/p_tp. At finite p_tp the answer depends on the gas. In this book's van der Waals model, a nitrogen bulb filled to 1,000 kPa reads 375.82 K at the steam point (373.124 K), and helium 373.19 K. As p_tp is lowered every gas tends to the same value: the ideal-gas temperature, equal to the thermodynamic temperature.

Constant-volume gas thermometer: readings of different gases converge as the fill pressure goes to zero: interactive loads as you scroll

How are the Kelvin, Celsius, Fahrenheit and Rankine scales related?

The kelvin was fixed for decades by giving the triple point of water exactly 273.16 K; since 2018 it is defined through the Boltzmann constant, and the triple point is still 273.16 K. Celsius is the kelvin shifted: t = T − 273.15, so the triple point is 0.01 °C. On ITS-90 water boils at 1 atm at about 99.974 °C, not exactly 100. Fahrenheit and Rankine use a degree 1.8 times smaller: t_F = 1.8t + 32 and T_R = 1.8T. So 0 K is −459.67 °F and 300 K is 540 R.

How do mercury, thermocouple and resistance thermometers compare?

Each uses a property that changes with temperature: a liquid's expansion (mercury in glass), the voltage of a junction of two metals (thermocouple), or the resistance of platinum (RTD). None is exactly linear. A Pt100 follows R = 100(1 + At + Bt²) Ω with the IEC 60751 values A = 3.9083e-3 and B = −5.775e-7. A scale made by calling its resistance 0 at the ice point and 100 at the steam point, with a straight line between, reads +0.375 °C at a true 50 °C and −3 °C at 200 °C. Calibrated thermometers use the curve, not the line.

Predict, then check

Four constant-volume thermometers (N2, O2, H2, He) are each filled to 1,000 kPa at the triple point, then put in boiling water. Which reads closest to the true temperature?

Worked examples

Reading a gas thermometer on four scales · A constant-volume gas thermometer reads 40.0 kPa at the triple point of water and 54.2 kPa in a bath. Treat the gas as ideal.
  1. T = 273.16 × 54.2/40.0 = 370.13 K
  2. t = T − 273.15 = 96.98 °C
  3. t_F = 1.8 × 96.98 + 32 = 206.57 °F
  4. T_R = 1.8 × 370.13 = 666.24 R

Answer: 370.13 K = 96.98 °C = 206.6 °F = 666.2 R

Extrapolating to zero fill pressure · A nitrogen thermometer in a bath of boiling water is refilled three times. Readings 273.16·p/p_tp (computed from the van der Waals model): p_tp = 200 kPa: 373.656 K; 400 kPa: 374.192 K; 600 kPa: 374.731 K.
  1. The readings rise by about 0.536 K per 200 kPa: a straight line in p_tp
  2. Least-squares line: slope 2.6875 K per 1,000 kPa, intercept 373.118 K
  3. By hand: 373.656 − 0.536 = 373.12 K
  4. The intercept at p_tp = 0 is the ideal-gas temperature, independent of the gas

Answer: T ≈ 373.12 K (99.97 °C): water at 1 atm on ITS-90 boils at about 373.124 K

A Pt100 and a two-point linear scale · A Pt100 (R0 = 100 Ω, A = 3.9083e-3, B = −5.775e-7) is at 150 °C. Then a reading of 120.00 Ω is taken at an unknown temperature.
  1. R(150) = 100(1 + 3.9083e-3 × 150 − 5.775e-7 × 150²) = 157.325 Ω
  2. Linear 0-100 scale: R(100) = 138.5055 Ω, so t_lin = 100 × (157.325 − 100)/38.5055 = 148.88 °C, −1.12 °C off
  3. 120 Ω: solve Bt² + At − 0.2 = 0; the root near 50 °C is t = (−A + √(A² + 0.8B))/(2B) = 51.566 °C (a bisection on R(t) = 120 Ω agrees)
  4. The linear scale would call 120 Ω 51.94 °C

Answer: 157.33 Ω at 150 °C (linear scale 148.88 °C); 120 Ω is 51.57 °C (linear scale 51.94 °C)

Chapter 3

Work and heat: displacement work on the p-V diagram and other work modes

Which syllabus covers thisAU ME3391 Unit IVTU BME304 Module 1SPPU 202043 Unit IMU MEC305 Module 1KTU PCMET403 Modules 1, 2

Why is displacement work the area under the path on a p-V diagram?

When a gas pushes a piston of area A through dx with pressure p, it does work pA·dx = p dV. Adding up these strips along a quasi-static path gives the area under the curve on a p-V diagram. This book counts W as positive when the system does it (expansion) and negative when work is done on it (compression). Heat Q is positive when added to the system. The area is only defined when the gas passes through equilibrium states; a free expansion into vacuum pushes nothing and does no work.

Displacement work as the area under a p-V path: the same end states, different paths, different work: interactive loads as you scroll

Why is work a path function and not a property?

Take air from 5 bar and 1 litre to 1 bar and 4 litres. Expanding at 5 bar first and then cooling at constant volume does 1500 J of work. Cooling first and then expanding at 1 bar does only 300 J. The polytropic path pV^n = C through both states (n = 1.161) gives 621 J. Same end states, different work: W depends on the path, so it is written δW, never dW, and a system never 'contains' work.

What other forms of work cross a boundary?

Work is any energy transfer whose sole effect outside could be the raising of a weight. Besides p dV there is shaft work, 2πNT for a shaft turning N times per second against torque T; electrical work, V·I·t; spring work, ½k(x2² − x1²); and stirring work done by a paddle on a fluid. A paddle wheel in a rigid tank does work on the gas even though its volume never changes, so dV = 0 does not mean W = 0. Stirring work can only go into a fluid, never come back out as stirring.

What is heat, and how is it different from work?

Heat is energy crossing a boundary because of a temperature difference, and nothing else. Like work it is a transfer, not something stored, and it depends on the path. For the 5 bar to 1 bar change above, the air's ΔU is −250.2 J on every path, so the first law gives Q = ΔU + W: 1249.8 J on the expand-first path and 49.8 J on the cool-first path. An adiabatic process has Q = 0, either because of insulation or because it is too quick for heat to flow.

Predict, then check

Air goes from 5 bar, 1 litre to 1 bar, 4 litres. Path A: expand at 5 bar, then cool at constant volume. Path B: cool at constant volume to 1 bar, then expand. Which does more work?

Worked examples

Polytropic expansion · Air in a cylinder expands from 8 bar and 0.5 litre to 2 litres along pV^1.3 = constant.
  1. p2 = 8 × (0.5/2)^1.3 = 1.3195 bar
  2. W = (p1V1 − p2V2)/(n − 1) = (800 × 0.5 − 131.95 × 2)/0.3 J (kPa·L = J) = 453.7 J
  3. A numerical ∫p dV (Simpson) gives the same 453.7 J
  4. An isothermal expansion over the same volumes would give p1V1 ln 4 = 554.5 J: the steeper polytrope does less

Answer: p2 = 1.32 bar, W = 454 J done by the gas

Pushing a spring and the atmosphere · A gas lifts a frictionless piston of area 0.01 m² by 5 cm. A spring (k = 20 kN/m) touches the piston at the start with no force; the atmosphere outside is at 101.325 kPa. Neglect the piston's weight.
  1. Against the atmosphere: p0·A·x = 101.325 × 0.01 × 0.05 kJ = 50.66 J
  2. Against the spring: ½kx² = ½ × 20,000 × 0.05² = 25 J
  3. The gas pressure rises linearly to p0 + kx/A = 201.325 kPa; ∫p dV over the 0.5 litre gives 75.66 J
  4. Both parts are work done by the gas, so W is positive

Answer: W = 75.66 J (50.66 J to the atmosphere, 25 J stored in the spring)

Work with no change in volume · A rigid tank of gas holds a 230 V heater drawing 2.5 A and a paddle wheel turning at 300 rpm with a torque of 1.2 N·m, both for 10 minutes.
  1. Displacement work is zero: the volume does not change
  2. Electrical work in: V·I·t = 230 × 2.5 × 600 = 345 kJ
  3. Shaft work in: 2πNT·t = 2π × 5 × 1.2 × 600 = 22.62 kJ
  4. Both are done on the system, so W = −(345 + 22.62) = −367.62 kJ

Answer: W = −367.6 kJ; if the tank is insulated, U rises by 367.6 kJ

Chapter 4

The first law: Joule's experiment, energy as a property, internal energy and enthalpy

Which syllabus covers thisAU ME3391 Unit IVTU BME304 Module 2SPPU 202043 Unit IMU MEC305 Module 1KTU PCMET403 Module 2

What did Joule's paddle-wheel experiment show?

Joule let weights of about 29 lb fall some 63 inches, twenty times over, turning paddles in an insulated can of water, and measured the tiny temperature rise. The heat produced by friction, in liquids or solids, was always proportional to the work spent. His 1850 result: raising 1 lb of water by 1 °F takes the fall of 772 lb through 1 ft. That is 4.154 J per calorie, within 0.8 % of today's 4.1868. The interactive's default, 13 kg falling 1.6 m twenty times into 6 kg of water, warms it by only 0.156 K. Switch on the room loss and 6.4 % of that leaks away during the 19-minute run: why Joule worked quickly.

Joule's paddle-wheel experiment: falling-weight work, the temperature rise and the first law for a cycle: interactive loads as you scroll

How does the first law for a cycle lead to energy as a property?

Over any cycle the net heat in equals the net work out: ∮δQ = ∮δW. Joule's water is the example: the paddles do work on it, and cooling it back to the start gives the same energy out as heat. Now go from state 1 to 2 by any path and come back by one fixed path. The cycle law forces Q − W to be the same for every path from 1 to 2, so Q − W is the change of a property, the internal energy: ΔU = Q − W. In the work chapter, every path had ΔU = −250.2 J. A machine giving work forever without heat (a PMM of the first kind) is impossible.

What is internal energy, and why does an ideal gas's depend only on temperature?

Internal energy is the energy stored in the molecules: their motion (translation, rotation, vibration) and the forces between them. In an ideal gas the molecules do not attract each other, so spreading them out costs nothing and u depends on temperature alone: du = cv dT. Heating 1 kg of air from 300 K to 400 K raises u by 0.718 × 100 = 71.8 kJ, at any pressure and along any path. Only changes of U matter in engineering; its zero is arbitrary.

What is enthalpy, and why is it useful?

Enthalpy is H = U + pV. At constant pressure the boundary work is pΔV, so Q = ΔU + pΔV = ΔH: the heat added at constant pressure equals the rise in enthalpy. Heat 1 kg of air from 300 K to 400 K at constant pressure and it takes cp·ΔT = 100.5 kJ: 71.8 kJ raises U and 28.7 kJ is work pushing the piston. For an ideal gas cp − cv = R. Enthalpy also carries the flow work pv of a stream, which is why steady-flow problems use h.

Predict, then check

Joule's falling weights do 4.08 kJ of work on a can of water, which warms slightly. The water is then cooled back to exactly its starting temperature. How much heat leaves it?

Worked examples

Joule's number in modern units · Joule (1850): 772 ft·lbf raise 1 lb of water by 1 °F. 1 ft·lbf = 1.355818 J, 1 lb = 0.45359237 kg, 1 °F step = 5/9 K. His weights: two of about 29 lb, falling about 63 inches, 20 times.
  1. 772 × 1.355818 = 1046.69 J per lb per °F
  2. Divide by 0.45359237 kg and by 5/9 K: 4153.6 J/kg K = 4.1536 J per calorie (1 g, 1 K)
  3. Against the IT calorie (4.1868 J): −0.79 %; against the thermochemical calorie (4.184 J): −0.73 %
  4. One experiment: 2 × 29 lb = 26.31 kg falling 1.6002 m, 20 times: W = 8260 J

Answer: 4.154 J/cal, 0.8 % below the modern value; about 8.3 kJ of work per experiment

Stirring a rigid tank that leaks heat · A rigid tank holds 2 kg of air. A paddle driven by a 400 W motor stirs it for 5 minutes while 30 kJ of heat escapes. cv = 0.718 kJ/kg K.
  1. W = −400 × 300 s = −120 kJ (work done on the air)
  2. Q = −30 kJ (heat leaves)
  3. ΔU = Q − W = −30 − (−120) = +90 kJ
  4. ΔT = ΔU/(m cv) = 90/(2 × 0.718) = 62.67 K

Answer: ΔU = +90 kJ; the air warms by 62.7 K

Closing the books on a cycle · A gas runs a four-process cycle. 1-2: Q = +120 kJ, W = +40 kJ. 2-3: adiabatic, W = +60 kJ. 3-4: Q = −70 kJ. 4-1: adiabatic, ΔU = +30 kJ. Find W34, W41 and the net work.
  1. ΔU12 = 120 − 40 = 80 kJ; ΔU23 = 0 − 60 = −60 kJ
  2. Over the cycle ΣΔU = 0: ΔU34 = −(80 − 60 + 30) = −50 kJ
  3. W34 = Q34 − ΔU34 = −70 − (−50) = −20 kJ; W41 = 0 − 30 = −30 kJ
  4. Net W = 40 + 60 − 20 − 30 = 50 kJ = net Q = 120 − 70

Answer: W34 = −20 kJ, W41 = −30 kJ, net work 50 kJ (equal to the net heat)

Chapter 5

Ideal-gas processes: isochoric, isobaric, isothermal, adiabatic and polytropic

Which syllabus covers thisAU ME3391 Units I, IIIVTU BME304 Module 1SPPU 202043 Unit IIMU MEC305 Module 1KTU PCMET403 Module 2

How are the five classic processes one family?

Each is a curve pv^n = C on the p-v diagram. n = 0 is constant pressure, n = 1 is constant temperature for an ideal gas, n = γ (1.4 for air) is reversible adiabatic, and n → ∞ is constant volume. Real compressions and expansions fall in between and are fitted with an index n. Compress 1 kg of air from 1 bar and 300 K to 10 bar: isothermally the gas needs 198.3 kJ/kg of work and rejects all of it as heat; adiabatically it needs 200.3 kJ/kg and keeps it, leaving at 579 K. Sign convention: W done by the gas and Q added to it are positive, so ΔU = Q − W.

Ideal-gas processes pv^n = C: work, heat, internal energy and entropy change from isobaric to isochoric: interactive loads as you scroll

How can a gas take in heat while its temperature falls?

Along pv^n = C the heat is Q = cn(T2 − T1), with the polytropic specific heat cn = cv(n − γ)/(n − 1). For n between 1 and γ it is negative. Expand air from 1 bar and 300 K along n = 1.3 to 0.2 bar: it cools to 206.9 K yet takes in 22.2 kJ/kg, because it does 89 kJ/kg of work, more than its internal energy drops (66.8 kJ/kg). cn = −0.239 kJ/kg K. The heat slows the cooling; it cannot stop it. At n = 1 cn is infinite (heat with no temperature change), at n = γ it is zero.

Why is ΔU = cv ΔT even when the volume changes?

For an ideal gas the internal energy depends on temperature alone (Joule's free-expansion result), so ΔU = cv(T2 − T1) and ΔH = cp(T2 − T1) on any path, not only at constant volume or pressure. What the path decides is how ΔU splits between Q and W. Heat 1 kg of air from 300 K to 600 K: at constant volume Q = ΔU = 215.4 kJ/kg; at constant pressure Q = ΔH = 301.5 kJ/kg, the extra 86.1 kJ/kg (R ΔT) leaving as work. That gap is why cp − cv = R.

How does each process look on the T-s diagram?

For an ideal gas Δs = cv ln(T2/T1) + R ln(v2/v1). The isothermal is horizontal and the isentropic vertical. Constant-volume and constant-pressure lines both curve upwards, slopes T/cv and T/cp, so the isochoric is steeper. Heating air from 300 K to 600 K raises s by 0.498 kJ/kg K at constant volume and 0.697 kJ/kg K at constant pressure. The area under a reversible path on T-s is the heat, just as the area under it on p-v is the work.

Predict, then check

1 kg of air expands from 1 bar and 300 K along pv^1.3 = C to 0.2 bar. Its temperature falls. What about heat?

Worked examples

Compressing air three ways to the same pressure · 1 kg of air, 1 bar and 300 K, compressed to 8 bar: isothermal, polytropic n = 1.25, isentropic (n = γ = cp/cv ≈ 1.4). R = 0.287, cv = 0.718 kJ/kg K
  1. v1 = RT1/p1 = 0.287 × 300/100 = 0.861 m³/kg
  2. Isothermal: W = RT1 ln(p1/p2) = 86.1 × ln(1/8) = −179 kJ/kg; ΔU = 0, so Q = W = −179 kJ/kg
  3. n = 1.25: T2 = 300 × 8^(0.25/1.25) = 454.7 K; W = R(T1 − T2)/(n − 1) = −177.6 kJ/kg; ΔU = 0.718 × 154.7 = 111.1 kJ/kg; Q = ΔU + W = −66.5 kJ/kg
  4. Isentropic: T2 = 300 × 8^((γ − 1)/γ) = 543.3 K; Q = 0, W = −ΔU = −174.7 kJ/kg
  5. A Simpson integration of p dv along each curve gives the same works

Answer: W = −179, −177.6 and −174.7 kJ/kg; heat rejected 179, 66.5 and 0 kJ/kg; exit at 300, 455 and 543 K

Heating at constant volume vs constant pressure · 2 kg of air at 1 bar, 300 K. (a) Rigid vessel heated until the pressure is 3 bar. (b) The same temperature rise at a constant 1 bar
  1. (a) Constant volume: T2 = 300 × 3/1 = 900 K, W = 0
  2. Q = m cv ΔT = 2 × 0.718 × 600 = 861.6 kJ; ΔS = m cv ln 3 = 1.578 kJ/K
  3. (b) Constant pressure to 900 K: Q = m cp ΔT = 2 × 1.005 × 600 = 1206 kJ
  4. W = m R ΔT = 2 × 0.287 × 600 = 344.4 kJ; ΔU = 861.6 kJ, the same as in (a)
  5. ΔS = m cp ln 3 = 2.208 kJ/K

Answer: (a) Q = 861.6 kJ, ΔS = 1.578 kJ/K; (b) Q = 1206 kJ, W = 344.4 kJ, ΔS = 2.208 kJ/K

Finding n from two measured states · Air expands from 8 bar, 0.04 m³ and 600 K to 1.5 bar and 0.15 m³ along pV^n = C
  1. n = ln(p1/p2)/ln(V2/V1) = ln(5.333)/ln(3.75) = 1.2665
  2. m = p1V1/(RT1) = 800 × 0.04/(0.287 × 600) = 0.1858 kg; T2 = p2V2/(mR) = 421.9 K
  3. W = (p1V1 − p2V2)/(n − 1) = (32 − 22.5)/0.2665 = 35.65 kJ (Simpson on p dV agrees)
  4. ΔU = m cv (T2 − T1) = 0.1858 × 0.718 × (−178.1) = −23.77 kJ
  5. Q = ΔU + W = 11.88 kJ: heat flows in (n lies between 1 and γ)

Answer: n = 1.266, W = 35.7 kJ, ΔU = −23.8 kJ, Q = +11.9 kJ

Chapter 6

Energy balance for closed systems: pistons, stops, springs and stirrers

Which syllabus covers thisAU ME3391 Unit IVTU BME304 Module 2SPPU 202043 Unit IMU MEC305 Module 1KTU PCMET403 Module 2

What does the first law say for a closed system?

No mass crosses the boundary, so the energy stored can change only by heat and work: Q − W = ΔU + ΔKE + ΔPE, and for gas in a cylinder the kinetic and potential terms are usually negligible. W counts every kind of work done by the system: the moving boundary (∫p dV), a rotating shaft, an electric current. Work done on the gas, like a paddle wheel stirring it, enters as a negative W. Heat in is positive. Draw the boundary first; whether something is heat or work depends on where it is.

What happens when a piston rests on stops and you heat the gas?

Until the gas pressure reaches the lift pressure (piston weight plus atmosphere) the piston cannot move: heating at constant volume, W = 0. Then the piston rises at constant pressure. If it hits upper stops, it is constant volume again. Take 5 litres of air at 100 kPa and 300 K, lift at 200 kPa and top stops at 7.5 litres: the first 1.25 kJ only raise p, the piston travels until 3 kJ, and with 2.5 kJ the gas is at 814 K having done 0.357 kJ of work. The p-V path is a staircase.

Closed-system energy balance: a piston with stops, a spring-loaded piston and paddle-wheel work: interactive loads as you scroll

Why is the path a straight line with a linear spring?

Force balance on the piston: p = p1 + k(V − V1)/A², because the spring force k·x grows with the travel x = ΔV/A. So p rises linearly with V and the work is a trapezoid, W = (p1 + p2)(V2 − V1)/2. A soft spring tends to constant pressure, a stiff one to constant volume. With k = 5 kN/m on a 100 cm² piston (50 kPa per litre) and 2 kJ added to 5 litres of air at 100 kPa, 300 K: V reaches 6.64 litres, p 181.9 kPa, T 724 K, and only 0.231 kJ leaves as work.

Is a paddle wheel heat or work, and does it matter?

Shaft work crosses the boundary through a turning shaft, so a paddle wheel stirring the gas is work done on it (W negative). The state change is identical to adding the same energy as heat: in a rigid 5-litre tank of air (5.81 g), 1 kJ either way raises the temperature by 240 K. The difference is irreversibility: paddle work cannot be got back by turning the paddle backwards. An electric heater is work if the boundary includes the resistor and heat if it surrounds only the gas.

Predict, then check

Air at 100 kPa is under a piston that lifts only at 200 kPa. You add the first 1 kJ of heat. How much work does the gas do?

Worked examples

Piston on stops: three stages · 10 litres of air at 100 kPa, 300 K under a piston on stops; it lifts at 250 kPa and upper stops hold it at 15 litres. 6 kJ of heat is added
  1. m = pV/(RT) = 100 × 0.01/(0.287 × 300) = 0.01161 kg
  2. Stage 1 (stops, constant V) ends at T = 300 × 250/100 = 750 K: Q = m cv ΔT = 3.753 kJ
  3. Stage 2 (constant p) would end at the top stops at T = 250 × 0.015/(mR) = 1125 K, after Q = 8.13 kJ in all, so 6 kJ stops inside stage 2
  4. T = 750 + (6 − 3.753)/(m cp) = 942.5 K; V = mRT/p = 12.567 litres
  5. W = 250 × (12.567 − 10)/1000 = 0.642 kJ; ΔU = m cv ΔT = 5.358 kJ; ΔU + W = 6 kJ (a 3,000-step heating simulation agrees)

Answer: Still rising at 250 kPa: T = 943 K, V = 12.57 litres, W = 0.642 kJ, ΔU = 5.36 kJ

Spring-loaded piston · 4 litres of air at 150 kPa, 300 K; a linear spring adds 25 kPa per litre of expansion. Heated until V = 6 litres
  1. p2 = 150 + 25 × 2 = 200 kPa
  2. T2 = T1 p2V2/(p1V1) = 300 × (200 × 6)/(150 × 4) = 600 K
  3. W = (p1 + p2)/2 × ΔV = 175 × 0.002 = 0.35 kJ (trapezoid under the straight line)
  4. m = 0.006969 kg; ΔU = m cv ΔT = 0.006969 × 0.718 × 300 = 1.501 kJ
  5. Q = ΔU + W = 1.851 kJ (RK4 in Q along the spring line ends at 6 litres)

Answer: p2 = 200 kPa, T2 = 600 K, W = 0.35 kJ, Q = 1.85 kJ

Paddle wheel in a leaky rigid tank · Rigid 20-litre tank of air at 100 kPa, 25 °C. A paddle wheel takes 30 W from its shaft for 2 minutes while 1.2 kJ of heat leaks out
  1. Paddle work done on the gas: 30 × 120 = 3600 J, so W = −3.6 kJ; Q = −1.2 kJ
  2. ΔU = Q − W = −1.2 + 3.6 = 2.4 kJ
  3. m = 100 × 0.02/(0.287 × 298.15) = 0.02337 kg; ΔT = ΔU/(m cv) = 143 K
  4. Rigid: p2 = p1 T2/T1 = 100 × 441.2/298.15 = 148 kPa

Answer: T rises by 143 K to 168 °C and p to 148 kPa

Chapter 7

The steady-flow energy equation and steady-flow devices

Which syllabus covers thisAU ME3391 Unit IVTU BME304 Module 2SPPU 202043 Unit IMU MEC305 Module 1KTU PCMET403 Module 2

Where does enthalpy come from in the steady-flow energy equation?

In steady flow the mass and energy inside the control volume do not change, so what enters equals what leaves. Every kilogram pushed in carries its internal energy u plus the flow work pv done by the fluid behind it; u + pv is the enthalpy h. Per kilogram, heat in minus shaft work out equals the rise in h, kinetic and potential energy. Velocities are in m/s, so divide V²/2 by 1,000 for kJ/kg: 100 m/s is only 5 kJ/kg, and a 10 m rise is 0.098 kJ/kg. In most machines Δh dominates.

Steady-flow energy equation for nozzles, turbines, compressors, pumps, throttles and mixing chambers: interactive loads as you scroll

How do nozzles and diffusers use the equation?

Neither has a shaft, and both are too quick and short to lose much heat, so q = w = 0 and the kinetic energy changes only at the expense of enthalpy. In a nozzle, air entering at 600 K and 50 m/s that cools by 100 K leaves at √(50² + 2 × 1,005 × 100) = 451 m/s. A diffuser runs it backwards: air slowed from 250 to 30 m/s warms by 30.6 K, which is why the air at a jet engine's compressor face is warmer than outside.

What matters in turbines, compressors and pumps?

Shaft work and the enthalpy change; kinetic and potential terms are small. Steam entering a turbine at 40 bar and 450 °C and leaving at 0.1 bar, 90 % dry, at 120 m/s instead of 40 m/s, with 10 kJ/kg lost as heat, gives 969.9 kJ/kg: 9.7 MW at 10 kg/s. The velocity change costs 6.4 kJ/kg, 0.7 % of it. For a pump, the liquid hardly changes volume, so w ≈ v Δp: 15.84 kJ/kg from 5 to 150 bar against 15.78 kJ/kg from the steam tables. Values are illustrative.

What do a throttle and a mixing chamber conserve?

A throttle (a partly closed valve, a porous plug) has no work, negligible heat and negligible velocity change, so h2 = h1: enthalpy is unchanged, though pressure falls and entropy rises. Wet steam at 10 bar, 97 % dry, throttled to 1 bar leaves superheated at 120 °C, 20.4 K above saturation; that is how a throttling calorimeter measures dryness. A mixing chamber conserves total enthalpy flow: 0.4 kg/s of water at 80 °C and 0.6 kg/s at 20 °C leave at 44.02 °C.

Predict, then check

Steam at 10 bar, 97 % dry, passes through a throttle valve to 1 bar. Leaving the valve it is:

Worked examples

Exit velocity and area of an air nozzle · Air enters an adiabatic nozzle at 700 K and 40 m/s and leaves at 580 K and 1.2 bar; mass flow 2 kg/s; cp = 1.005 kJ/kg K
  1. q = w = 0, ΔPE = 0: (V2² − V1²)/2 = cp(T1 − T2)
  2. V2 = √(40² + 2 × 1,005 × 120) = √242800 = 492.7 m/s
  3. Exit specific volume v2 = RT2/p2 = 0.287 × 580/120 = 1.3872 m³/kg
  4. Area A2 = ṁ v2/V2 = 2 × 1.3872/492.7 = 0.00563 m²

Answer: V2 = 493 m/s, A2 = 56.3 cm²

Power of a steam turbine with every term kept · Steam at 60 bar, 500 °C, 50 m/s enters; it leaves at 0.1 bar, dryness 0.92, 150 m/s, 2 m lower; heat loss 15 kJ/kg; 25 kg/s (illustrative). IF97 steam properties
  1. h1 = 3422.9 kJ/kg (superheated, 60 bar, 500 °C)
  2. h2 = hf + x hfg at 0.1 bar = 191.8 + 0.92 × 2392.1 = 2392.5 kJ/kg
  3. ΔKE = (150² − 50²)/2,000 = 10 kJ/kg; ΔPE = 9.81 × (−2)/1,000 = −0.0196 kJ/kg
  4. w = q − Δh − ΔKE − ΔPE = −15 + 1030.4 − 10 + 0.02 = 1005.4 kJ/kg
  5. Power = 25 × 1005.4 = 25136 kW. Check: the isentropic exit dryness is 0.831, below 0.92, so the exit is possible

Answer: w = 1005 kJ/kg, power ≈ 25.1 MW; KE and PE change it by under 1 %

Boiler feed pump: v·Δp against the steam tables · Saturated water at 6 bar is pumped to 150 bar, 150 kg/s, reversibly and adiabatically; then with an 80 % efficient pump (operating point illustrative)
  1. Inlet: saturated liquid at 6 bar, 158.8 °C, h1 = 670.5 kJ/kg, v1 = 0.0011006 m³/kg
  2. Incompressible estimate: w = v Δp = 0.0011006 × 14,400 kPa = 15.85 kJ/kg
  3. Steam tables: the 150 bar state with s2 = s1 has h2 = 686.29 kJ/kg, so w = 15.79 kJ/kg (0.37 % apart)
  4. Ideal power = 150 × 15.79 = 2368 kW
  5. With η = 0.8: w = 19.74 kJ/kg, power = 2961 kW

Answer: About 15.8 kJ/kg; 2.37 MW ideal, 2.96 MW at 80 % efficiency

Chapter 8

Unsteady flow: filling and emptying tanks

Which syllabus covers thisAU ME3391 Unit IVTU not in syllabusSPPU not in syllabusMU not in syllabusKTU not in syllabus

How do you write the first law when the mass inside changes?

Use the tank as a control volume and account over the whole process: the mass rise equals the mass that came in minus what went out, and the internal energy rise m2u2 − m1u1 equals the enthalpy carried in minus the enthalpy carried out, plus heat in, minus work out. Incoming mass brings h, not u, because the gas behind it does flow work pv to push it through the valve. For a rigid tank with one inlet from a line at constant state this becomes the relation below.

Unsteady flow: filling and emptying a rigid tank, and why the gas comes out hotter than the line: interactive loads as you scroll

Why is air that fills an empty tank hotter than the line?

From vacuum, with no heat loss, m2u2 = m2h_line, so cv T2 = cp T_line and T2 = γ T_line. A 300 K line gives 419.9 K (147 °C) whatever the line pressure or tank size. The flow work done by the line gas pushing each parcel in ends up as internal energy of the tank gas. A 100-litre tank filled to 10 bar this way holds only 0.83 kg, against 1.161 kg once it cools to 300 K at the same pressure.

What happens after a quick fill, and with heat loss?

Starting from 3 bar instead of vacuum, the old gas is compressed and the new gas heated, ending in between: 100 litres filled to 10 bar from a 300 K line reach 375 K. Close the valve and let it cool to the room and the pressure falls to 8 bar, so a receiver filled fast needs topping up. With the valve open while heat leaks out, the tank keeps drawing air as it cools, ending at the line pressure and temperature with the full mass.

How fast does air flow through the valve, and what happens on discharge?

While the downstream pressure is below 0.528 of the upstream (the critical ratio for air), the valve throat is choked: sonic, and the mass flow depends only on the upstream state and the area. A 10 mm² ideal valve from a 10 bar, 300 K line passes 23.3 g/s into any tank below 5.28 bar. Emptying a tank adiabatically, the gas left inside expands isentropically: from 10 bar and 300 K down to 1 atm it reaches 156 K. Real tank walls warm it, so measured temperatures fall less.

Predict, then check

An evacuated, insulated rigid bottle is opened to the room air at 25 °C and 1 atm. When the flow stops, the air inside is at:

Worked examples

Filling an evacuated tank · A 50-litre rigid insulated tank, evacuated, is filled from a line at 8 bar and 27 °C until the flow stops; then it cools to 27 °C with the valve shut
  1. Energy balance m2u2 = m2h_line: T2 = γT_line = (1.005/0.718) × 300 = 419.9 K
  2. m2 = p2V/(RT2) = 800 × 0.05/(0.287 × 419.9) = 0.3319 kg
  3. Enthalpy carried in = m2 cp T_line = 100.07 kJ, equal to U2 = m2 cv T2 (energy check)
  4. After cooling at constant volume: p = 8 × 300/419.9 = 5.715 bar
  5. An RK4 integration of the filling (mass and energy equations, choked then unchoked valve) ends at the same state

Answer: T2 = 420 K (147 °C), m2 = 0.332 kg; it cools to 5.72 bar

Topping up an air receiver · A 200-litre receiver holds air at 2 bar, 27 °C; it is connected to a 7 bar line at 27 °C and filled quickly (adiabatic) to 7 bar (illustrative)
  1. m1 = 200 × 0.2/(0.287 × 300) = 0.4646 kg
  2. Energy: m2 cv T2 − m1 cv T1 = (m2 − m1) cp T_line, with m2T2 = p2V/R
  3. So m2 − m1 = (p2 − p1)V/(γRT_line) = 500 × 0.2/(γ × 0.287 × 300) = 0.8298 kg; m2 = 1.2943 kg
  4. T2 = p2V/(m2R) = 140/(1.2943 × 0.287) = 376.9 K
  5. Cooled back to 300 K with the valve shut: p = 7 × 300/376.9 = 5.57 bar

Answer: 0.83 kg added, T2 = 377 K; it settles at 5.57 bar, not 7

Blowing down a cylinder through a small valve · A 40-litre cylinder of air at 10 bar and 300 K empties to the atmosphere (1.01325 bar) through an ideal 5 mm² valve; no heat transfer
  1. Critical ratio (2/(γ + 1))^(γ/(γ−1)) = 0.5283: the valve is choked while the tank is above 1.01325/0.5283 = 1.918 bar
  2. Initial flow (choked): ṁ = A p0 √(γ/(RT0)) (2/(γ + 1))^((γ+1)/(2(γ−1))) = 11.67 g/s
  3. The gas left inside expands isentropically: T = 300 × (p/1,000)^((γ−1)/γ); at 1.918 bar T = 187.2 K, at 1 atm T = 156 K
  4. Mass: 0.4646 kg at the start, 0.0905 kg left at 1 atm
  5. Energy carried out = U1 − U2 = 89.9 kJ

Answer: Choked down to 1.92 bar; the remaining gas reaches 156 K (−117 °C) with 0.091 kg left

Chapter 9

The second law: heat engines, refrigerators, heat pumps, Kelvin-Planck and Clausius

Which syllabus covers thisAU ME3391 Unit IIVTU BME304 Module 3SPPU 202043 Unit IIMU MEC305 Module 2KTU PCMET403 Module 3

What does the first law leave out?

Direction. A 0.25 kg cup of tea cooling from 80 °C to 30 °C gives 52.25 kJ to the room. The first law would be just as happy if the tea took those 52.25 kJ back and reheated itself, and that never happens. Likewise a paddle wheel turns all of its work into heat, but no machine turns heat from one body entirely into work. The second law is the rule that decides which of the energy-balanced processes can actually happen.

What do heat engines, refrigerators and heat pumps do?

Each runs in a cycle between a hot reservoir at TH and a cold one at TL (bodies so large their temperatures do not change). An engine takes QH, delivers work W and must reject QL, so η = W/QH. A refrigerator uses W to lift QL out of the cold space; a heat pump is the same machine valued for the QH it delivers. With TH = 600 K, TL = 300 K, QH = 100 kJ and W = 40 kJ, η = 40 % against a Carnot limit of 50 %. Flows here are magnitudes; in equations W by the system and Q into it are positive.

Heat engines, refrigerators and heat pumps tested against the first law, Kelvin-Planck, Clausius and Carnot: interactive loads as you scroll

What do the Kelvin-Planck and Clausius statements say?

Kelvin-Planck (Kelvin, 1851): no device working in a cycle can take heat from a single reservoir and turn all of it into work. Every engine must reject some heat, so η is always below 100 %. A machine that broke this, say a ship running on the heat of the sea alone, is a perpetual motion machine of the second kind (PMM2). Clausius (1850): no cyclic device can move heat from a colder to a hotter body with no other effect. A refrigerator needs work. In the interactive both show up as negative entropy generation.

Why are the two statements equivalent?

Because breaking one breaks the other. Suppose an engine broke Kelvin-Planck, turning 50 kJ from a 600 K reservoir entirely into work. Use that work to drive an ordinary refrigerator (COP 0.8, below its Carnot value of 1) that lifts 40 kJ from 300 K and rejects 90 kJ at 600 K. Taken together, the pair moves 40 kJ from cold to hot with no work at all: a Clausius violator, with Sgen = −0.0667 kJ/K. The reverse argument works the same way. Press Proof in the interactive to see it.

Predict, then check

An inventor's engine takes 100 kJ from a 600 K source, delivers 55 kJ of work and rejects 45 kJ to a 300 K sink. Is it possible?

Worked examples

A heat-pump water heater · Illustrative: a heat pump delivers 3 kW to a water tank at 55 °C, takes heat from 30 °C outdoor air and draws 0.9 kW of electricity
  1. First law: QL = QH − W = 3 − 0.9 = 2.1 kW taken from the air
  2. COP = QH/W = 3/0.9 = 3.33
  3. Carnot limit: TH/(TH − TL) = 328.15/25 = 13.13
  4. Sgen = QH/TH − QL/TL = 3/328.15 − 2.1/303.15 = 2.21 W/K > 0
  5. An electric resistance heater would draw the full 3 kW: the heat pump uses 30 % of that

Answer: COP 3.33 (Carnot 13.1); possible and irreversible, Sgen = 2.21 W/K

Judging three engine claims · Each engine takes QH = 500 kJ from 800 K and rejects to 300 K. Claims: A W = 300, QL = 200 kJ; B W = 320, QL = 180 kJ; C W = 250, QL = 200 kJ
  1. Carnot limit: 1 − 300/800 = 62.5 %
  2. A: 300 + 200 = 500, first law fine; η = 60 % < 62.5 %; Sgen = −500/800 + 200/300 = +0.0417 kJ/K: possible
  3. B: 320 + 180 = 500, first law fine; η = 64 % > 62.5 %; Sgen = −0.625 + 0.6 = −0.025 kJ/K: impossible
  4. C: 250 + 200 = 450 ≠ 500, 50 kJ unaccounted: it fails the first law before the second is even asked

Answer: A possible (irreversible), B impossible (beats Carnot), C impossible (first law)

Building a Clausius violator from a Kelvin-Planck violator · Reservoirs at 400 K and 300 K. A claimed engine turns 40 kJ from 400 K entirely into work; it drives a real refrigerator that lifts 100 kJ from 300 K
  1. Refrigerator: COP = 100/40 = 2.5, below the Carnot value 300/(400 − 300) = 3, so it is a real machine
  2. It rejects 100 + 40 = 140 kJ to the 400 K reservoir
  3. Net for the pair: the 400 K reservoir gains 140 − 40 = 100 kJ, the 300 K reservoir loses 100 kJ, net work 0
  4. Entropy of the reservoirs: 100/400 − 100/300 = −0.0833 kJ/K < 0

Answer: The pair moves 100 kJ from 300 K to 400 K with no work: breaking Kelvin-Planck lets you break Clausius

Chapter 10

The Carnot cycle, Carnot's theorem and the thermodynamic temperature scale

Which syllabus covers thisAU ME3391 Unit IIVTU BME304 Module 3SPPU 202043 Unit IIMU MEC305 Module 2KTU PCMET403 Module 3

What are the four processes of the Carnot cycle?

Sadi Carnot described it in 1824. 1→2: the gas expands at TH in contact with the hot reservoir, taking QH. 2→3: insulated, it expands reversibly and cools to TL. 3→4: in contact with the cold reservoir it is compressed at TL, rejecting QL. 4→1: insulated, compressed back to TH. For 1 kg of air between 800 K and 300 K with V2/V1 = 3: QH = RTH ln 3 = 252.2 kJ, QL = 94.6 kJ, net work 157.7 kJ and η = 62.5 %. On a T-s diagram the cycle is a rectangle.

The Carnot cycle of an ideal gas on p-V and T-s, its efficiency and the reversed Carnot cycle: interactive loads as you scroll

What does Carnot's theorem say, and why is it true?

No engine working between two reservoirs can be more efficient than a reversible one, and every reversible engine between the same two reservoirs has the same efficiency. Proof: run a reversible engine backwards as a refrigerator, and let a supposedly better engine take from the hot reservoir exactly the heat the refrigerator returns to it. The better engine makes more work than the refrigerator needs, and the surplus can only come from the cold reservoir: net work from a single reservoir, which Kelvin-Planck forbids. So the limit depends only on TH and TL, not on the working fluid.

How does the Carnot cycle define temperature?

Because every reversible engine between two reservoirs has the same efficiency, the heat ratio QH/QL depends only on the two temperatures. Kelvin (1848) used this to define a scale independent of any substance: TH/TL = QH/QL for a reversible engine. The size of the unit was fixed in 1954 by giving the triple point of water exactly 273.16 K. Since 20 May 2019 the kelvin is instead fixed by the Boltzmann constant, 1.380649 × 10⁻²³ J/K, and the triple point is measured at 273.1600 K. The ideal-gas scale agrees with this scale exactly.

Why does no real engine run on the Carnot cycle?

The isothermal legs must transfer heat across a vanishing temperature difference, so they take forever. And the volumes are enormous. For 800 K and 300 K with V2/V1 = 3 and 1 bar at the bottom, the gas must expand 34.9 times and reach 93 bar at the top. All that machinery yields a mean effective pressure of only 1.89 bar: very little work per stroke volume. Real cycles, such as Rankine and Brayton (Thermal Engineering book), trade some efficiency for practical size and speed.

Predict, then check

A reversed Carnot refrigerator keeps a freezer at −10 °C in a 30 °C kitchen. What is its COP?

Worked examples

A Carnot engine on 1 kg of air · TH = 700 K, TL = 320 K, isothermal expansion V2/V1 = 2.5, state 3 (largest volume) at 1 bar; R = 0.287, cv = 0.718 kJ/kg K
  1. QH = R TH ln(V2/V1) = 0.287 × 700 × ln 2.5 = 184.08 kJ
  2. QL = R TL ln(V3/V4) = 0.287 × 320 × ln 2.5 = 84.15 kJ (the two isothermal ratios are equal)
  3. W = QH − QL = 99.93 kJ; η = W/QH = 54.29 % = 1 − 320/700
  4. Adiabats: V3/V2 = (TH/TL)^(cv/R) = 7.087; overall V3/V1 = 17.72
  5. v3 = RTL/p3 = 0.9184 m³/kg, v1 = 0.0518 m³/kg, so p1 = 38.8 bar and MEP = W/(v3 − v1) = 1.153 bar

Answer: η = 54.3 %, W = 99.9 kJ per kg per cycle, peak 38.8 bar, MEP 1.15 bar

Reversed Carnot cycle as a heat pump · Illustrative: a room kept at 22 °C needs 5 kW while the outdoor air is at 5 °C; ideal (Carnot) heat pump
  1. COP_HP = TH/(TH − TL) = 295.15/17 = 17.36
  2. Work = 5/17.36 = 0.288 kW
  3. Heat from outside = 5 − 0.288 = 4.712 kW
  4. Same machine as a refrigerator: COP_R = TL/(TH − TL) = 16.36 = COP_HP − 1, and 1/COP_HP = 5.76 % is the Carnot efficiency between the same temperatures

Answer: At best 288 W of work buys 5 kW of heat (COP 17.4); real heat pumps reach a fraction of this

Temperatures from heat ratios · (a) A reversible engine rejects heat to a bath at the triple point of water (273.16 K) and takes in 1.8 times as much heat as it rejects. (b) Two reversible engines in series run between 1000 K and 300 K, the first rejecting to an intermediate reservoir that feeds the second
  1. (a) TH/TL = QH/QL, so TH = 1.8 × 273.16 = 491.69 K
  2. (b) Equal work: QH − QM = QM − QL, so TH − TM = TM − TL and TM = 650 K
  3. (b) Equal efficiency: 1 − TM/TH = 1 − TL/TM, so TM = √(1000 × 300) = 547.7 K; each engine then has η = 45.2 %
  4. Either way the overall efficiency is 1 − 300/1000 = 70 %: reversible engines in series behave as one

Answer: (a) 491.69 K; (b) 650 K for equal work, 547.7 K for equal efficiency

Chapter 11

Reversible and irreversible processes and the Clausius inequality

Which syllabus covers thisAU ME3391 Unit IIVTU BME304 Module 3SPPU 202043 Unit IIMU MEC305 Module 2KTU PCMET403 Module 3

What makes a process reversible?

A process is reversible if the system and its surroundings can both be put back exactly as they were, leaving no trace anywhere. That needs a quasi-static process (a chain of equilibrium states) with no friction and with heat crossing only infinitesimal temperature differences. Real processes only approach it. A process is internally reversible when nothing irreversible happens inside the system, even if heat crosses a finite temperature difference at its boundary; the Carnot cycle and the ideal-gas paths in this book are of that kind.

What makes real processes irreversible?

Friction; heat transfer across a finite temperature difference; unrestrained (free) expansion; mixing of different substances or states; throttling; electrical resistance; and fast, non-quasi-static compression. Each one generates entropy. Take 1 kJ of heat flowing straight from 400 K to 300 K: the cold body gains 1/300 kJ/K and the hot body loses 1/400, so Sgen = 0.833 J/K. A Carnot engine between the same two bodies could have produced 0.25 kJ of work from that heat; the direct flow throws it away.

What is the Clausius inequality?

For any cycle, the sum of each heat flow divided by the temperature where it crosses the boundary is at most zero (Clausius, 1854). It equals zero for a reversible cycle and is negative for an irreversible one; a positive value means the cycle is impossible. In the interactive's default engine (627 °C and 27 °C reservoirs, 70 % of the span used), the sum taken at the reservoirs is −0.517 kW/K, exactly minus Sgen. Taken at the working fluid, whose own cycle is reversible, it is zero.

What efficiency does an engine have when it gives maximum power?

A Carnot engine has zero power, because its heat must cross zero temperature difference. With finite heat exchangers, the fluid runs between TH' below TH and TL' above TL. Using more of the span raises η but starves the heat flow. Power peaks at η = 1 − √(TL/TH) (Curzon and Ahlborn, 1975), and with equal exchangers the fluid then uses exactly half the span. Between 900 K and 300 K that is 42.3 %, against 66.7 % for Carnot. The coal, nuclear and geothermal presets compare it with real plants.

Irreversibility through finite temperature differences: the Clausius inequality and the engine at maximum power: interactive loads as you scroll
Predict, then check

An engine between 800 K and 300 K with equal finite heat exchangers is tuned for maximum power. About what efficiency does it reach?

Worked examples

Testing three cycles with the Clausius inequality · A cycle takes 1000 kJ from a 1000 K reservoir and rejects to a 300 K reservoir. Claimed rejections: (a) 500 kJ, (b) 300 kJ, (c) 250 kJ
  1. (a) ∮δQ/T = 1000/1000 − 500/300 = −0.6667 kJ/K < 0: irreversible, possible (η = 50 %)
  2. (b) 1 − 300/300 = 0: reversible (η = 70 %, the Carnot value)
  3. (c) 1 − 250/300 = +0.1667 kJ/K > 0: impossible (η = 75 % would beat Carnot)
  4. Sign: heat into the cycle positive, heat out negative, each divided by the boundary temperature

Answer: (a) irreversible, (b) reversible, (c) impossible

An endoreversible engine at maximum power · Reservoirs 900 K and 300 K; exchangers with UA = 10 kW/K on each side (illustrative); the fluid's cycle is internally reversible
  1. η at maximum power = 1 − √(300/900) = 42.26 %; a golden-section search over η finds the same peak
  2. Entropy balance of the fluid, QH/TH' = QL/TL' with TL' = TH'(1 − η): TH' = 709.8 K, TL' = 409.8 K
  3. QH = 10 × (900 − 709.8) = 1902 kW; QL = 10 × (409.8 − 300) = 1098 kW
  4. Power = 803.8 kW = (UA/2)(√900 − √300)²; the fluid spans 300 K, half of 600 K
  5. Sgen = QL/TL − QH/TH = 1.547 kW/K. Pushing η up to 50 % cuts the power to 750 kW

Answer: η = 42.3 %, power 804 kW, Sgen 1.55 kW/K

Real power plants against Carnot and Curzon-Ahlborn · Reservoir temperatures and observed efficiencies as published (Curzon and Ahlborn 1975, via the Wikipedia table on endoreversible thermodynamics)
  1. West Thurrock (coal): 25/565 °C, Carnot 64.4 %, maximum-power 40.4 %, observed 36 %
  2. CANDU (nuclear): 25/300 °C, Carnot 48 %, maximum-power 27.9 %, observed 30 %
  3. Larderello (geothermal): 80/250 °C, Carnot 32.5 %, maximum-power 17.8 %, observed 16 %
  4. In every case the observed efficiency sits close to the maximum-power value and far below Carnot: plants are designed for output, not for the reversible limit

Answer: Observed 36, 30 and 16 % against maximum-power predictions of 40, 28 and 18 %

Chapter 12

Entropy as a property: T-s diagrams and the Tds equations

Which syllabus covers thisAU ME3391 Unit IIVTU BME304 Module 3SPPU 202043 Unit IIIMU MEC305 Module 2KTU PCMET403 Module 3

Why is entropy a property?

Take two states and two different reversible paths between them. Going out by one and back by the other is a reversible cycle, so the Clausius sum ∮δQ/T is zero. The integral of δQrev/T is therefore the same along both paths: it depends only on the end states. Clausius named that quantity entropy (1865). For 1 kg of air from 300 K and 1 bar to 600 K and 8 bar, every path gives Δs = 1.005 ln 2 − 0.287 ln 8 = 0.0998 kJ/kg K, although the heat along them differs.

What does the area under a T-s path mean?

For a reversible process δq = T ds, so the area under the path on a T-s diagram, down to absolute zero, is the heat per kg; moving left (s falling) means heat out. Between the same two air states as above, path A (isothermal, then isobaric) takes in 122.5 kJ/kg, path B (isobaric, then isothermal) gives out 56.6 kJ/kg and path C (isochoric, then isothermal) gives out 23.3 kJ/kg. Δu = 215.4 kJ/kg on all three, so the work differs too.

Entropy is a property: different paths between two states, the same change in entropy, different heat: interactive loads as you scroll

What are the Tds equations?

For a simple compressible substance in a reversible process, the first law gives δq = du + p dv and the second gives δq = T ds. Joined, and with h = u + pv, they give the two relations below. They contain only properties, so they hold for any process between two states, reversible or not. For an ideal gas, du = cv dT and pv = RT, so Δs = cv ln(T2/T1) + R ln(v2/v1) = cp ln(T2/T1) − R ln(p2/p1).

How does entropy change for liquids and for steam?

An incompressible liquid has dv ≈ 0, so T ds = c dT and Δs = c ln(T2/T1). Steam is not an ideal gas, so its entropy comes from tables (IAPWS-IF97 here). Across the saturation dome, heat goes in at constant temperature, so sfg = hfg/Tsat. At 1 bar that is 2257.5/372.76 = 6.0562 kJ/kg K. The steam mode of the interactive follows one isobar through liquid, dome and superheat.

Predict, then check

1 kg of air goes from 300 K and 1 bar to 600 K and 8 bar by two different reversible paths. Which quantity is the same for both?

Worked examples

Same entropy change, three different heats · 1 kg of air from 320 K, 1.5 bar to 480 K, 3 bar; reversible paths A (isothermal then isobaric), B (isobaric then isothermal), C (isochoric then isothermal); cp = 1.005, cv = 0.718, R = 0.287 kJ/kg K
  1. Δs = 1.005 ln(480/320) − 0.287 ln(3/1.5) = 0.4075 − 0.1989 = 0.2086 kJ/kg K
  2. A: −0.287 × 320 × ln 2 + 1.005 × 160 = 97.14 kJ/kg
  3. B: 1.005 × 160 − 0.287 × 480 × ln 2 = 65.31 kJ/kg
  4. C: 0.718 × 160 − 0.287 × 480 × ln(3/2.25) = 75.25 kJ/kg (the isochoric leg ends at 1.5 × 480/320 = 2.25 bar)
  5. Work w = q − Δu with Δu = 0.718 × 160 = 114.88 kJ/kg: A −17.74, B −49.57, C −39.63 kJ/kg
  6. Numerical integration of (cv dT + p dv)/T along each path returns the same Δs every time

Answer: Δs = 0.2086 kJ/kg K on every path; q = 97.1, 65.3 and 75.2 kJ/kg

Heating water for a bath · 2 kg of water heated from 25 °C to 80 °C; incompressible, c = 4.18 kJ/kg K
  1. Q = m c ΔT = 2 × 4.18 × 55 = 459.8 kJ
  2. ΔS = m c ln(T2/T1) = 8.36 × ln(353.15/298.15) = 1.4153 kJ/K
  3. The heat enters at a mean temperature Q/ΔS = 324.87 K, the log mean of the two end temperatures
  4. Using the arithmetic mean 325.65 K instead gives 1.4119 kJ/K, 0.24 % too low

Answer: ΔS = 1.415 kJ/K for 460 kJ of heat

Steam at constant pressure, from liquid to superheat · 1 kg of water at 10 bar and 100 °C heated at constant pressure to 300 °C; IAPWS-IF97 properties
  1. Tsat at 10 bar = 179.89 °C; state 1 is compressed liquid: h1 = 419.8 kJ/kg, s1 = 1.3063 kJ/kg K
  2. State 2 is superheated: h2 = 3051.7 kJ/kg, s2 = 7.1247 kJ/kg K
  3. q = h2 − h1 = 2631.9 kJ/kg: 342.9 to reach saturation, 2014.4 to boil (hfg), 274.6 to superheat
  4. Δs = 5.8184 kJ/kg K, of which hfg/Tsat = 4.4465 comes from boiling; ∫cp dT/T over the two single-phase legs gives the rest (0.8321 + 0.5397)
  5. Mean temperature of heat addition q/Δs = 452.3 K

Answer: q = 2631.9 kJ/kg, Δs = 5.8184 kJ/kg K

Chapter 13

The increase-of-entropy principle and entropy generation

Which syllabus covers thisAU ME3391 Unit IIIVTU BME304 Module 3SPPU 202043 Unit IIIMU MEC305 Module 2KTU PCMET403 Module 3

What is the increase-of-entropy principle?

Draw a boundary around a system and everything it interacts with, and the total is isolated. For any process inside, the entropy of that whole can only rise or, in the reversible limit, stay the same. The rise is the entropy generated, Sgen. Pass 1,000 kJ of heat from a body at 500 K to one at 300 K: the hot one loses 1,000/500 = 2 kJ/K, the cold one gains 1,000/300 = 3.333 kJ/K, so Sgen = 1.333 kJ/K. A negative Sgen would be a process running against the second law.

How do you find Sgen for a real process?

Write an entropy balance like the energy balance: the change of the system's entropy equals the entropy carried in with heat (Q/T at the boundary temperature) and with mass, plus Sgen. Or add the entropy changes of every body involved. Quench a 2 kg steel block (c = 0.49 kJ/kg K) at 400 °C in 10 kg of water at 25 °C: both settle at 33.59 °C. The block loses 0.77 kJ/K, the water gains 1.187 kJ/K, so Sgen = 0.417 kJ/K, all of it from heat crossing a large temperature difference.

Entropy generation in heat transfer, quenching, free expansion, throttling and mixing, and the lost work: interactive loads as you scroll

What does entropy generation cost?

Work that could have been had, T0·Sgen, with T0 the environment temperature (25 °C here). Let 1 kg of air at 25 °C rush into an equal empty volume: no work, no heat, same temperature, yet Sgen = R ln 2 = 0.1989 kJ/K. A slow reversible isothermal expansion between the same states would have delivered 59.3 kJ, exactly T0·Sgen. For heat through a wall of fixed conductance UA, Sgen = UA·ΔT²/(TH·TL): for a small ΔT, halving it cuts Sgen to about a quarter, but you also move only half the heat.

Where does entropy start counting from?

Engineering problems need only entropy changes, so steam tables pick a convenient zero (since 1956, u and s of saturated liquid water at the triple point). The third law, worked out by Nernst between 1906 and 1912, gives an absolute zero: the entropy of a pure, perfect crystal tends to zero as the temperature approaches 0 K. Absolute entropy is then the integral of C/T dT from 0 K, plus the latent heat over temperature at each phase change. Chemists use these absolute values for reactions, where differences between substances matter.

Predict, then check

Air is throttled from 10 bar to 1 bar through an insulated valve. As an ideal gas, its temperature does not change. Is entropy generated?

Worked examples

Entropy generated by a hot oven wall · Oven wall at steady state with an illustrative conductance UA = 8 W/K; inside 220 °C, kitchen 35 °C; T0 = 25 °C. Then the inside is set to 127.5 °C (ΔT halved).
  1. Heat flow Q = UA·ΔT = 8 × 185 = 1,480 W from 493.15 K to 308.15 K
  2. The wall itself is at steady state: its entropy does not change
  3. Sgen = Q/TL − Q/TH = 1,480/308.15 − 1,480/493.15 = 1.802 W/K
  4. Lost power T0·Sgen = 298.15 × 1.802 = 537 W
  5. At 127.5 °C inside: Q = 740 W, Sgen = 0.554 W/K, 30.8 % of before, lost power 165 W

Answer: 1.8 W/K and 537 W of lost work potential; halving ΔT cuts Sgen to about 31 %

Quenching a steel forging · 3 kg carbon steel (c = 0.49 kJ/kg K) at 600 °C dropped into 25 kg water (c = 4.18 kJ/kg K) at 25 °C in an insulated tank; T0 = 25 °C
  1. Energy balance: 3 × 0.49 × (873.15 − Tf) = 25 × 4.18 × (Tf − 298.15) gives Tf = 306.13 K (32.98 °C)
  2. Heat given up by the steel: 833.5 kJ
  3. ΔS steel = 3 × 0.49 × ln(306.13/873.15) = −1.5407 kJ/K
  4. ΔS water = 25 × 4.18 × ln(306.13/298.15) = +2.7589 kJ/K
  5. Sgen = −1.5407 + 2.7589 = 1.2182 kJ/K; lost work T0·Sgen = 363.2 kJ

Answer: Tf = 33 °C, Sgen = 1.218 kJ/K, 363 kJ of the 834 kJ could have been work

Mixing hot and cold water in a shower mixer · 0.10 kg/s at 60 °C and 0.15 kg/s at 20 °C, adiabatic, steady; water c = 4.18 kJ/kg K; T0 = 25 °C
  1. Energy: 0.10 × (60 − T3) = 0.15 × (T3 − 20), so T3 = 36 °C
  2. Hot stream: 0.10 × 4.18 × ln(309.15/333.15) = −31.25 W/K
  3. Cold stream: 0.15 × 4.18 × ln(309.15/293.15) = +33.32 W/K
  4. Sgen = 2.07 W/K, lost power T0·Sgen = 616.5 W

Answer: 36 °C water, Sgen = 2.1 W/K, about 617 W of work potential lost

Chapter 14

Isentropic processes and the isentropic efficiency of turbines and compressors

Which syllabus covers thisAU ME3391 Unit IIIVTU not in syllabusSPPU not in syllabusMU not in syllabusKTU PCMET403 Modules 3, 4

What makes a process isentropic?

A process that is both adiabatic and reversible: no heat carries entropy in or out and none is generated, so s stays constant. For an ideal gas with constant specific heats this fixes T·p^(−R/cp) (the familiar pv^γ = constant, γ ≈ 1.4 for air). Compress air at 25 °C eight-fold this way and it leaves at 539.9 K, 266.8 °C. Real machines are close to adiabatic but never reversible, so the isentropic process is the ideal they are measured against.

How is isentropic efficiency defined?

Compare the real machine with an isentropic one working between the same inlet state and the same exit pressure. A turbine delivers less than the isentropic drop, so ηT = actual work / isentropic work. A compressor needs more, so ηC = isentropic work / actual work. Air at 25 °C compressed eight-fold needs 243 kJ/kg ideally; at ηC = 0.85 it takes 285.9 kJ/kg and leaves at 309 °C instead of 267 °C. With W positive when done by the system, the compressor's work is negative, −285.9 kJ/kg.

Isentropic efficiency of compressors and turbines on the T-s and h-s diagrams, for air and steam: interactive loads as you scroll

Is the work lost to friction the same as T0·sgen?

No. Friction heats the fluid, so a turbine's exit is hotter than 2s, and h2 − h2s is the work the machine failed to deliver. But that heat leaves in the exhaust above the environment temperature, so part of it could still drive another engine. Only T0·sgen is gone for good. In a gas turbine from 1,000 °C and 8 bar to 1 bar at η = 0.85, h2 − h2s = 85.9 kJ/kg while T0·sgen = 34.4 kJ/kg. Combined-cycle plants recover much of the difference in a steam cycle.

How do steam turbines and nozzles fit this picture?

For steam you read h1 and s1 from the tables, find 2s at the exit pressure with s2s = s1 (often wet, with a quality x2s), then h2 = h1 − η(h1 − h2s). Friction leaves the exhaust drier: steam from 40 bar, 400 °C expanded to 0.1 bar has x2s = 0.816, but at η = 0.85 it leaves with x2 = 0.883. A nozzle turns the drop into speed instead of shaft work: its efficiency is the actual exit kinetic energy over the isentropic drop, so the velocity falls by √η.

Predict, then check

Two steam turbines take the same inlet steam to the same condenser pressure. One is less efficient. Its exhaust steam is:

Worked examples

A workshop air compressor · Air at 1 bar, 30 °C compressed adiabatically to 7 bar, isentropic efficiency 0.80 (illustrative); cp = 1.005, R = 0.287 kJ/kg K; T0 = 25 °C
  1. Isentropic exit: T2s = 303.15 × 7^(0.287/1.005) = 528.44 K (bisection on s(T2s, 7 bar) = s1 gives the same)
  2. Isentropic work: ws = 1.005 × (528.44 − 303.15) = 226.41 kJ/kg
  3. Actual work: w = 226.41/0.80 = 283.02 kJ/kg, so W by the air = −283.02 kJ/kg
  4. Actual exit: T2 = 303.15 + 283.02/1.005 = 584.76 K (311.6 °C)
  5. sgen = 1.005 ln(584.76/528.44) = 0.1018 kJ/kg K; T0·sgen = 30.35 kJ/kg, less than the extra work 56.6 kJ/kg

Answer: 283 kJ/kg of work in, exit 312 °C, 30.3 kJ/kg destroyed

A condensing steam turbine · Steam at 80 bar, 480 °C expands to 0.08 bar, isentropic efficiency 0.86 (illustrative); IAPWS-IF97 properties; T0 = 25 °C
  1. Inlet: h1 = 3,349.5 kJ/kg, s1 = 6.6611 kJ/kg K
  2. At 0.08 bar with s = s1: x2s = 0.7948, h2s = 2,083.4 kJ/kg
  3. Isentropic work 1,266.2 kJ/kg; actual w = 0.86 × 1,266.2 = 1,088.9 kJ/kg
  4. h2 = 2,260.6 kJ/kg, so x2 = 0.8686, s2 = 7.2244 kJ/kg K
  5. sgen = 0.5633 kJ/kg K; T0·sgen = 168 kJ/kg against h2 − h2s = 177.3 kJ/kg (the exhaust is at 41.5 °C, above T0)

Answer: w = 1,089 kJ/kg, exhaust quality 0.869, 168 kJ/kg destroyed

Isentropic efficiency of a steam nozzle · Steam at 15 bar, 300 °C, negligible inlet velocity, expands to 5 bar; nozzle efficiency 0.92 (illustrative); IAPWS-IF97
  1. h1 = 3,038.3 kJ/kg, s1 = 6.9199 kJ/kg K
  2. At 5 bar with s = s1 the steam is still superheated: T2s = 170.5 °C, h2s = 2,791.2 kJ/kg
  3. Isentropic drop 247 kJ/kg, V2s = √(2 × 247 × 1000) = 703 m/s
  4. Actual kinetic energy 0.92 × 247 = 227.3 kJ/kg, so V2 = 674 m/s (= √0.92 × V2s)
  5. Actual exit: h2 = 2,811.0 kJ/kg, T2 = 179.3 °C

Answer: 674 m/s instead of 703 m/s; the exit is 8.9 K warmer than the isentropic one

Chapter 15

High- and low-grade energy: available and unavailable energy of heat

Which syllabus covers thisAU ME3391 Unit IIIVTU BME304 Module 4SPPU 202043 Unit IIIMU MEC305 Module 3KTU PCMET403 Module 3

Why is some energy worth more than other energy?

Work, electricity and the kinetic energy of a shaft are high-grade: in principle all of it can become any other form. Heat is low-grade: even a reversible engine turns only the fraction 1 − T0/T into work, where T0 is the environment it rejects to. With T0 = 25 °C, 1,000 kJ of heat at 1,000 K can give at most 701.9 kJ of work, but the same 1,000 kJ at 400 K only 254.6 kJ. The first law counts both as 1,000 kJ; the second law says the hotter heat is worth almost three times as much.

What are available and unavailable energy?

Split heat Q from a source into the part a reversible engine rejecting at T0 could turn into work, the available energy, and the rest it must reject, the unavailable energy, T0·ΔS, where ΔS is the entropy the source gives up. On a T-s diagram from 0 K, Q is the area under the source's line; the strip below T0 is unavailable. For 1,000 kJ from a reservoir at 800 °C with T0 = 25 °C: available 722.2 kJ, unavailable 277.8 kJ.

Available and unavailable energy of heat: constant-temperature and cooling sources, and the dead state: interactive loads as you scroll

What if the source cools down as it gives heat?

Then each slice of heat arrives at a lower temperature and is worth less. For a body of heat capacity mc cooling from T1 all the way to T0, the available energy is mc[(T1 − T0) − T0 ln(T1/T0)]. Ten kilograms of steel at 800 °C hold 3,797.5 kJ above 25 °C, but only 1,926.4 kJ (50.7 %) is available, against 72.2 % for a reservoir held at 800 °C. The body behaves like a reservoir at its mean temperature Q/ΔS = 332 °C.

What happens to available energy when heat flows across a temperature difference?

It shrinks, though no energy is lost. Pass 1,000 kJ from a source at 1,000 K to a receiver at 500 K: the receiver gains 1,000/500 = 2 kJ/K of entropy while the source lost only 1 kJ/K, so the unavailable part grows by T0·Sgen = 298.15 × 1 = 298.15 kJ. This is the degradation of energy. A boiler is the classic example: hot combustion gases hand their heat to much cooler steam across a large temperature gap.

Predict, then check

With the environment at 25 °C, which carries more available energy: 1,000 kJ of heat from steam condensing at 1 bar (99.6 °C), or 300 kJ from a reservoir at 1,000 °C?

Worked examples

Heat from a furnace · A furnace at a steady 1,100 °C supplies 5,000 kJ of heat; the surroundings are at 30 °C
  1. Entropy given up by the furnace: ΔS = 5,000/1373.15 = 3.6413 kJ/K
  2. Unavailable energy T0·ΔS = 303.15 × 3.6413 = 1,103.8 kJ
  3. Available energy = 5,000 − 1,103.8 = 3,896.2 kJ
  4. Fraction available = 1 − 303.15/1373.15 = 77.92 %

Answer: Available 3,896 kJ, unavailable 1,104 kJ

A cooling steel billet · 50 kg of carbon steel (c = 0.49 kJ/kg K) at 800 °C cools to the surroundings at 25 °C
  1. Heat given up: Q = 50 × 0.49 × 775 = 18,987.5 kJ
  2. Entropy given up: ΔS = 50 × 0.49 × ln(1073.15/298.15) = 31.379 kJ/K
  3. Unavailable energy T0·ΔS = 9,355.5 kJ
  4. Available energy = 18,987.5 − 9,355.5 = 9,632.0 kJ (50.7 %)
  5. Mean temperature of the heat Q/ΔS = 605.1 K (332 °C)

Answer: Of 18,988 kJ, only 9,632 kJ is available

Using condensing steam to heat a process tank · 2 kg of dry saturated steam condenses at 10 bar; its heat keeps a process tank at 90 °C; T0 = 25 °C; IAPWS-IF97
  1. At 10 bar: Tsat = 179.89 °C, hfg = 2,014.4 kJ/kg, so Q = 4,028.9 kJ
  2. Available at the steam: Q(1 − 298.15/453.04) = 1,377.4 kJ
  3. Available once in the tank at 363.15 K: Q(1 − 298.15/363.15) = 721.1 kJ
  4. Sgen = Q/363.15 − Q/453.04 = 2.2012 kJ/K
  5. Extra unavailable energy T0·Sgen = 656.3 kJ = 1,377.4 − 721.1

Answer: 48 % of the steam's available energy is lost in the drop of about 90 K

Chapter 16

Exergy, irreversibility and second-law efficiency of closed and flow systems

Which syllabus covers thisAU ME3391 Unit IIIVTU BME304 Module 4SPPU 202043 Unit IIIMU MEC305 Module 3KTU PCMET403 Module 3

What is exergy, and what is the dead state?

Exergy is the most useful work you can get from a system as it comes to equilibrium with its environment by reversible processes. When it is at the environment's temperature and pressure (here 25 °C and 1.01325 bar) nothing more can be had: that is the dead state, where exergy is zero. Zoran Rant coined the word in 1956. A 200 litre tank of air at 10 bar and 25 °C has exactly the internal energy of the same 2.337 kg of room air, yet it holds 278.1 kJ of exergy, all from its pressure.

How is exergy calculated for a closed system and for a stream?

For a closed mass, φ = (u − u0) + p0(v − v0) − T0(s − s0): the p0 term is the work spent pushing back the atmosphere, which is not useful. A flowing stream also brings its flow work, so ψ = (h − h0) − T0(s − s0) + V²/2 (+ gz). Steam at 30 bar, 350 °C and 40 m/s, measured from liquid water at 25 °C, carries h − h0 = 3,011.1 kJ/kg of energy but ψ = 1,110.4 kJ/kg of exergy: about 37 %.

Exergy of closed and flowing systems, exergy destroyed (Gouy-Stodola) and second-law efficiency: interactive loads as you scroll

Where does exergy go in a real device?

Unlike energy, exergy is not conserved. The exergy balance reads: exergy in = work out + exergy out + exergy destroyed, and the destroyed part, the irreversibility I, equals T0·Sgen. This is the Gouy-Stodola theorem (Gouy 1889, Stodola 1905). An air turbine taking air at 800 °C through a pressure ratio of 6 to the atmosphere at an isentropic efficiency of 0.85 destroys 28.6 kJ/kg, exactly 298.15 × 0.096. The exhaust's exergy is not destroyed: a recovery boiler could still use it.

What does second-law efficiency tell you that the first-law efficiency does not?

It compares what a device achieves with the best possible: exergy delivered over exergy supplied, or actual work over reversible work. The turbine above has an isentropic efficiency of 0.85 but a second-law efficiency of 92.8 %. An electric heater keeping a room at 20 °C on a 5 °C day turns every joule into heat, 100 % by the first law, but the heat is worth only 1 − 278.15/293.15 = 5.12 % of the electricity. A reversible heat pump would need just 1/19.5 of the power.

What are the Helmholtz and Gibbs functions?

Two properties made for work at constant temperature. Helmholtz a = u − Ts: in a closed system exchanging heat only with surroundings at its own temperature, the most work it can do is the drop in a. Gibbs g = h − Ts plays the same role for a steady flow at constant temperature, and also at constant T and p for chemical reactions and phase change. The least work to compress air isothermally at 25 °C from 1 to 10 bar is Δg = RT0 ln 10 = 197 kJ/kg.

Predict, then check

A tank of compressed air at 10 bar has cooled down to room temperature, 25 °C. Does it still hold exergy?

Worked examples

Exergy of a warm compressed-air receiver · 0.5 m³ receiver with air at 8 bar, 60 °C (illustrative); dead state 25 °C, 1.01325 bar; cv = 0.718, cp = 1.005, R = 0.287 kJ/kg K
  1. v = RT/p = 0.287 × 333.15/800 = 0.11952 m³/kg, so m = 0.5/0.11952 = 4.183 kg; v0 = 0.8445 m³/kg
  2. u − u0 = 0.718 × 35 = 25.13 kJ/kg
  3. p0(v − v0) = 101.325 × (0.11952 − 0.8445) = −73.46 kJ/kg
  4. s − s0 = 1.005 ln(333.15/298.15) − 0.287 ln(8/1.01325) = −0.48147 kJ/kg K, so −T0(s − s0) = 143.55 kJ/kg
  5. φ = 95.22 kJ/kg (integrating the reversible route numerically gives the same), Φ = mφ = 398.4 kJ

Answer: Φ = 398 kJ of useful work at most, while U − U0 is only 105 kJ

Exergy carried by a steam line · 1.5 kg/s of steam at 20 bar, 300 °C, 50 m/s; dead state liquid water at 25 °C, 1.01325 bar; IAPWS-IF97
  1. Dead state: h0 = 104.93 kJ/kg, s0 = 0.3672 kJ/kg K
  2. Steam: h − h0 = 2,919.3 kJ/kg, s − s0 = 6.4013 kJ/kg K
  3. T0(s − s0) = 1,908.5 kJ/kg; V²/2 = 1.25 kJ/kg
  4. ψ = 2,919.3 − 1,908.5 + 1.25 = 1,012.0 kJ/kg
  5. Exergy flow 1.5 × ψ = 1,518 kW, against an energy flow of 4,381 kW

Answer: 1,518 kW of exergy (34.7 % of the energy flow)

Exergy account of an air compressor · Air at 1.01325 bar, 30 °C compressed to 5 times the pressure, isentropic efficiency 0.80 (illustrative); T0 = 25 °C; per kg/s
  1. T2s = 303.15 × 5^(0.287/1.005) = 480.03 K; work in w = 1.005 × (480.03 − 303.15)/0.80 = 222.2 kW
  2. T2 = 524.24 K; ψ1 = 0.042 kJ/kg (slightly warmer than the dead state), ψ2 = 195.84 kJ/kg
  3. Destroyed: I = ψ1 + w − ψ2 = 26.4 kW
  4. Check: sgen = 1.005 ln(524.24/303.15) − 0.287 ln 5 = 0.08856 kJ/kg K, T0·sgen = 26.4 kW
  5. Second-law efficiency (ψ2 − ψ1)/w = 88.1 %

Answer: 26.4 kW destroyed per kg/s; η_II = 88.1 % against ηC = 80 %

Chapter 17

Pure substances: phase change of water and the p-v, T-v and p-T diagrams

Which syllabus covers thisAU ME3391 Unit IVVTU BME304 Module 4SPPU 202043 Unit IVMU MEC305 Module 4KTU PCMET403 Module 4

What happens when you heat water at constant pressure?

Put 1 kg of water at 25 °C under a weighted piston at 1 atm and add heat. The liquid warms to 99.97 °C, taking 314 kJ. Then it boils at that fixed temperature: the next 2,257 kJ (the latent heat hfg) only turns liquid into vapour, and the volume grows about 1,600 times. Only when the last drop has gone does the temperature rise again: superheated vapour. A pure substance has one fixed chemical composition in every phase, so ice, water and steam together qualify.

Heating water at constant pressure: compressed liquid, wet steam, superheat, the T-v diagram and the p-T phase diagram: interactive loads as you scroll

What are saturated, wet and superheated states, and what is the dryness fraction?

While liquid and vapour coexist, pressure and temperature are tied: fix one and the other is the saturation value. So p and T together cannot locate a wet state; you need one more property. The dryness fraction x is the mass of vapour per kg of mixture: 0 for saturated liquid, 1 for dry saturated vapour, and any specific property is the mass-weighted mix of the two. Liquid below its saturation temperature is compressed (subcooled) liquid; vapour above it is superheated, by the degree of superheat T − Tsat.

What happens at the critical point?

Raise the pressure and the boiling plateau shrinks. At 1 bar water boils at 99.6 °C with hfg = 2,258 kJ/kg; at 100 bar at 311.0 °C with 1,318 kJ/kg; at 160 bar at 347.4 °C with only 931 kJ/kg. At the critical point (373.946 °C, 220.64 bar, 322 kg/m³) hfg reaches zero and liquid and vapour become the same. On the T-v diagram the saturated-liquid and saturated-vapour lines meet there and close the dome. Above it water never boils: it turns from liquid-like to gas-like smoothly, so a supercritical boiler has no drum separating water from steam.

What does the p-T phase diagram show?

Three lines meeting at the triple point (0.01 °C, 611.657 Pa), where ice, water and vapour coexist. The vaporisation curve runs from there to the critical point. Below 611.657 Pa there is no liquid: ice turns straight to vapour, at 103 Pa at −20 °C (IAPWS 2011 equations). Water's melting line leans left because ice is less dense than water, so pressure lowers the melting point, but only by 1 K per about 135 bar; keeping water liquid at −5 °C takes 60 MPa.

Predict, then check

Which needs more heat to turn 1 kg of saturated liquid water fully into vapour: boiling it at 1 bar or at 100 bar?

Worked examples

The heat budget of making steam at 5 bar · 1 kg of water at 25 °C in a piston-cylinder held at 5 bar is heated to 300 °C. IAPWS-IF97 properties.
  1. Tsat at 5 bar = 151.84 °C. Liquid at 25 °C: h0 = 105.3 kJ/kg, v0 = 0.001003 m³/kg.
  2. Warm the liquid to saturation: hf = 640.2, so q1 = 640.2 − 105.3 = 534.9 kJ/kg.
  3. Boil it: hg = 2,748.1, so q2 = hfg = 2,107.9 kJ/kg; v grows from vf = 0.001093 to vg = 0.3748 m³/kg.
  4. Superheat to 300 °C: h = 3,064.6 kJ/kg, so q3 = 316.5 kJ/kg; v = 0.5226 m³/kg.
  5. Total q = 2,959.3 kJ/kg: 18.1 % warming the liquid, 71.2 % boiling, 10.7 % superheating.

Answer: q = 2,959 kJ/kg, 71 % of it latent heat; the volume grows 521 times.

How much of a hot-water vessel is steam? · A sealed 50-litre vessel holds 5 kg of water at 150 °C in equilibrium (no air).
  1. Specific volume v = 0.05/5 = 0.01 m³/kg.
  2. At 150 °C: psat = 4.761 bar, vf = 0.001091, vg = 0.3925 m³/kg. vf < v < vg, so the water is wet.
  3. x = (v − vf)/(vg − vf) = (0.01 − 0.001091)/(0.3925 − 0.001091) = 0.02276.
  4. Vapour mass = 5 × 0.02276 = 0.1138 kg; its volume = 0.1138 × 0.3925 = 0.0447 m³, 89.3 % of the vessel.

Answer: p = 4.76 bar, x = 0.0228: 2.3 % of the mass but 89 % of the volume is vapour.

Melting ice by pressure, and freeze-drying · IAPWS 2011 melting curve of ice Ih: p/pt = 1 + 1,195,393.37(1 − θ³) + 80,818.3159(1 − θ^25.75) + 3,338.2686(1 − θ^103.75), and the sublimation curve; θ = T/273.16 K, pt = 611.657 Pa.
  1. At −1 °C, θ = 272.15/273.16 = 0.996303: p = 13.23 MPa (132 bar).
  2. At −5 °C: p = 59.98 MPa, about 600 bar.
  3. Slope at the triple point: dp/dT = −13.47 MPa/K, negative: squeezing ice melts it, at about 135 bar per kelvin.
  4. Sublimation at −20 °C: psubl = 103.2 Pa. Below this pressure ice at −20 °C turns straight into vapour, which is how a freeze-dryer works.

Answer: Water stays liquid at −5 °C only above 60.0 MPa; ice at −20 °C sublimes below 103 Pa.

Chapter 18

Steam tables, the Mollier chart and processes with steam

Which syllabus covers thisAU ME3391 Unit IVVTU BME304 Module 4SPPU 202043 Unit IVMU MEC305 Module 4KTU PCMET403 Module 4

How do you use steam tables?

Saturation tables list, against temperature or pressure, Tsat or psat with vf, vg, hf, hfg, hg, sf and sg (often u too); for a wet state you add x. Superheat tables list v, h and s at each pressure and temperature, and between rows you interpolate linearly. That is usually close: at 10 bar, halfway between 200 °C (h = 2,828.3) and 250 °C (2,943.2) interpolation gives 2,885.7 kJ/kg against the exact 2,887.0 at 225 °C, 1.3 kJ/kg low. This book computes every value from the IAPWS-IF97 equations, the ones the printed tables are generated from.

Why is the Mollier (h-s) chart useful?

It plots enthalpy against entropy, the two properties a steady-flow analysis needs. An ideal turbine or nozzle is a vertical line (constant s) whose length is the work or the kinetic energy gained; a throttle is a horizontal line (constant h). Constant-pressure lines fan out upward to the right, constant-temperature lines flatten in the superheat region (where steam starts to behave like an ideal gas, h depending on T alone), and lines of constant x fill the wet region below the saturation line. A state is read where two lines cross.

How do you find work and heat in a non-flow steam process?

Fix both end states from the tables, then use the path. W is the area under the path on the p-v diagram, positive when the steam expands (work done by the system, Q positive when added, so ΔU = Q − W). Rigid tank: W = 0, so Q = Δu. Constant pressure: W = p(v2 − v1) and Q = Δh. Reversible isothermal: Q = T(s2 − s1) and W = Q − Δu. Reversible adiabatic: s stays constant and W = u1 − u2. Polytropic pv^n = C: W = (p1v1 − p2v2)/(n − 1), and Q follows from the first law.

Non-flow and flow processes with steam: work, heat and property changes from IAPWS-IF97: interactive loads as you scroll

What changes for steady-flow processes such as throttling?

In steady flow the enthalpy h = u + pv carries the flow work, and the SFEE with kinetic and potential energy neglected gives q − w = h2 − h1. A turbine expanding steam isentropically from 15 bar, 300 °C to 1 bar delivers h1 − h2 = 527 kJ/kg, more than the 430 kJ/kg the same expansion gives in a closed cylinder, because the flow work p1v1 − p2v2 is added. A throttling valve does no work and loses no heat, so h2 = h1: the pressure drop is wasted and entropy rises.

Predict, then check

A rigid tank holds wet steam at 10 bar with x = 0.9. It cools until the pressure is 2 bar. What happens to x?

Worked examples

Heating wet steam at constant pressure · 2 kg of wet steam at 8 bar, x = 0.85, in a piston-cylinder is heated at constant pressure to 250 °C.
  1. Tsat at 8 bar = 170.41 °C. State 1 (wet): v1 = vf + x vfg = 0.2044 m³/kg, h1 = 2,461.2 kJ/kg, u1 = h1 − p v1 = 2,297.7 kJ/kg.
  2. State 2 (superheated, 8 bar, 250 °C): v2 = 0.2932 m³/kg, h2 = 2,950.5 kJ/kg, u2 = 2,716.0 kJ/kg.
  3. W = m p (v2 − v1) = 2 × 800 × (0.2932 − 0.2044) = 142.0 kJ (done by the steam).
  4. Q = m (h2 − h1) = 2 × (2,950.5 − 2,461.2) = 978.7 kJ.
  5. Check: ΔU = m (u2 − u1) = 836.7 kJ = Q − W.

Answer: W = 142 kJ, Q = 979 kJ, ΔU = 837 kJ.

Steam cooling in a rigid tank · A rigid 0.2 m³ tank holds dry saturated steam at 6 bar (158.83 °C). It cools until the pressure is 2 bar.
  1. State 1: vg = 0.3156 m³/kg, so m = 0.2/0.3156 = 0.6338 kg; u1 = ug = 2,566.8 kJ/kg.
  2. State 2: same v. At 2 bar vf = 0.001061, vg = 0.8857: x2 = (0.3156 − 0.001061)/(0.8857 − 0.001061) = 0.3555.
  3. u2 = uf + x2 (ug − uf) = 1,224.3 kJ/kg, at 120.21 °C.
  4. W = 0 (rigid). Q = m (u2 − u1) = 0.6338 × (1,224.3 − 2,566.8) = −850.9 kJ.

Answer: x2 = 0.356; 851 kJ leaves the tank and 0.408 kg condenses.

The same isentropic expansion, closed and flowing · 1 kg of steam at 15 bar, 300 °C expands reversibly and adiabatically to 1 bar, (a) in a closed cylinder, (b) through a turbine.
  1. State 1: h1 = 3,038.3 kJ/kg, s1 = 6.9199 kJ/kg K, v1 = 0.1697 m³/kg, u1 = 2,783.7 kJ/kg.
  2. s2 = s1. At 1 bar sf = 1.3026, sg = 7.3588, so x2 = (6.9199 − 1.3026)/(7.3588 − 1.3026) = 0.9275.
  3. h2 = 2,511.3 kJ/kg, v2 = 1.5713 m³/kg, u2 = 2,354.2 kJ/kg.
  4. (a) Closed, Q = 0: W = u1 − u2 = 429.5 kJ/kg.
  5. (b) Steady flow, q = 0: w = h1 − h2 = 526.9 kJ/kg. The extra 97.4 kJ/kg is the flow work p1v1 − p2v2.

Answer: x2 = 0.928; W = 430 kJ/kg closed, w = 527 kJ/kg in a turbine.

A polytropic expansion that rejects heat · 1 kg of steam at 10 bar, 250 °C expands slowly in a cylinder along pv^1.3 = constant to 2 bar.
  1. State 1: v1 = 0.2327 m³/kg, u1 = 2,710.5 kJ/kg.
  2. v2 = v1 (p1/p2)^(1/n) = 0.2327 × 5^(1/1.3) = 0.8027 m³/kg. At 2 bar vg = 0.8857 > v2, so the steam is wet: x2 = 0.9061, T2 = 120.21 °C.
  3. u2 = 2,339.0 kJ/kg, so Δu = −371.5 kJ/kg.
  4. W = (p1v1 − p2v2)/(n − 1) = (1,000 × 0.2327 − 200 × 0.8027)/0.3 = 240.7 kJ/kg.
  5. Q = Δu + W = −371.5 + 240.7 = −130.8 kJ/kg.

Answer: W = 241 kJ/kg, Q = −131 kJ/kg: heat leaves although the steam expands and does work.

Chapter 19

Measuring the dryness fraction: steam calorimeters

Which syllabus covers thisAU ME3391 Unit IVVTU BME304 Module 4SPPU 202043 Unit IVMU not in syllabusKTU PCMET403 Module 4

Why measure the dryness fraction, and why can't a thermometer do it?

Wet steam carries less energy per kg: at 10 bar every 0.01 of x is worth hfg/100 = 20.1 kJ/kg, and the water droplets erode turbine blades and pipe bends. In the wet region pressure and temperature are locked together (Tsat at the line pressure) whatever x is, so gauges cannot tell 0.85 from 0.99. A calorimeter takes a sample and turns x into something you can measure: an outlet temperature, a mass of water caught, or a rise in temperature.

How does a throttling calorimeter work, and when does it fail?

Steam sampled from the main is throttled through a small orifice to about atmospheric pressure. Throttling keeps h constant, and at the low pressure that enthalpy lies in the superheated region, where pressure and temperature fix h. So read p2 and T2, look up h2 and solve h2 = hf1 + x hfg1. The outlet must be superheated; this book asks for at least 5 K. From 10 bar to 1 atm that means x ≥ 0.955: wetter steam leaves still wet and the thermometer just reads Tsat.

Measuring the dryness fraction: throttling, separating, combined and barrel calorimeters: interactive loads as you scroll

What does a separating calorimeter measure?

It removes the water mechanically: the sample turns sharply round a baffle, droplets fall into a graduated chamber (mass mw), and the steam goes on to be condensed and weighed (ms). Then x = ms/(ms + mw). It handles very wet steam, but no separator catches every droplet; the water it misses is weighed as steam, so the reading is always high. With separator efficiency e the error is (1 − e)(1 − x): 0.02 for x = 0.90 and e = 0.8.

Why put a separator before a throttling calorimeter?

The separator removes most of the water, reading x1 = ms/(ms + mw), and passes steam dry enough for the throttle, which measures that stream's dryness x2 exactly. The dry vapour in the sample is x1 × x2 of the total, so x = x1·x2, and the separator does not need to be perfect. The same readings give its efficiency: the water it caught divided by all the water there was, mw/((1 − x)(ms + mw)).

What is a barrel (bucket) calorimeter?

The simplest and crudest: blow a weighed mass of steam into a barrel of cold water and measure the temperature rise. The energy the steam gives up as it condenses and cools equals the energy the water and barrel gain, and that fixes the steam's enthalpy and so x. Heat loss and the small temperature rise make it rough: in Example 3 an error of only 0.1 K in the final temperature moves x by 0.0043.

Predict, then check

A throttling calorimeter on a 10-bar line exhausts at 1 atm, and its outlet thermometer reads 99.97 °C. What is x?

Worked examples

Reading a throttling calorimeter · Steam main at 12 bar. The throttling calorimeter's outlet is at 1.0 bar and 112.0 °C.
  1. At 12 bar: hf1 = 798.5, hfg1 = 1,985.3 kJ/kg.
  2. Outlet: Tsat at 1 bar = 99.61 °C, so the steam is superheated by 12.39 K: the reading is valid.
  3. h2 = h(1 bar, 112 °C) = 2,700.4 kJ/kg, and throttling keeps h1 = h2.
  4. x = (h2 − hf1)/hfg1 = (2,700.4 − 798.5)/1,985.3 = 0.9580.
  5. Range check: with a 5 K margin the lowest readable x at 12 bar is 0.9504.

Answer: x = 0.958.

A separating-throttling calorimeter · On a 10-bar line the separator collects 0.15 kg of water while the steam passing through the throttle condenses to 2.85 kg. The throttle outlet is at 1 atm (1.01325 bar) and 118.0 °C.
  1. Separator: x1 = ms/(ms + mw) = 2.85/3.00 = 0.9500.
  2. Throttle: h2 = h(1.01325 bar, 118 °C) = 2,712.4 kJ/kg; at 10 bar hf = 762.7, hfg = 2,014.4 kJ/kg.
  3. x2 = (2,712.4 − 762.7)/2,014.4 = 0.9679 (above x_min = 0.9547: valid).
  4. x = x1 x2 = 0.9500 × 0.9679 = 0.9195.
  5. Water in the 3 kg sample = (1 − 0.9195) × 3 = 0.2415 kg; the separator caught 0.15 kg: efficiency 62.1 %.

Answer: x = 0.919; the separator alone would have said 0.95.

A barrel calorimeter, and how rough it is · 0.45 kg of steam from a 4-bar line is blown into a barrel holding 9 kg of water at 24 °C (barrel water equivalent 0.35 kg). The mixture settles at 51.6 °C. Take c = 4.18 kJ/kg K for the liquid, h ≈ c·t.
  1. Heat gained = (9 + 0.35) × 4.18 × (51.6 − 24) = 1,078.7 kJ.
  2. Per kg of steam: 1,078.7/0.45 = 2,397.1 kJ/kg, and the condensate still holds 4.18 × 51.6 = 215.7 kJ/kg.
  3. So h1 = 2,397.1 + 215.7 = 2,612.8 kJ/kg.
  4. At 4 bar hf = 604.7, hfg = 2,133.3: x = (2,612.8 − 604.7)/2,133.3 = 0.9413.
  5. A 0.1 K error in the final temperature changes x by 0.0043; a 0.5 K error by 0.021.

Answer: x ≈ 0.94, uncertain by about ±0.02 if the thermometer is good to 0.5 K.

Why the throttle alone fails on very wet steam · Steam at 10 bar with x = 0.90 is sampled by a throttling calorimeter exhausting at 1 atm.
  1. h1 = hf + x hfg = 762.7 + 0.90 × 2,014.4 = 2,575.7 kJ/kg.
  2. At 1 atm hg = 2,675.5 kJ/kg > h1, so after throttling the steam is still wet: x = 0.9557.
  3. The thermometer reads Tsat = 99.97 °C for any such steam: no information about x.
  4. With the 5 K margin the lowest readable x is 0.970 at 5 bar, 0.955 at 10 bar and 0.935 at 30 bar.

Answer: Put a separator first: it raises the dryness of the throttled stream above x_min, and x = x1·x2.

Chapter 20

Real gases: van der Waals, compressibility factor and the generalised chart

Which syllabus covers thisAU ME3391 Unit VVTU BME304 Module 5SPPU not in syllabusMU not in syllabusKTU PCMET403 Module 4

When does a gas stop behaving ideally?

Define the compressibility factor Z = pv/(RT), exactly 1 for an ideal gas. At high pressure the molecules' own volume pushes Z above 1; nearer the saturation dome their mutual attraction pulls it below 1. CO2 at 320 K and 50 bar has Z = 0.771 (NIST data), so pv = RT overestimates its volume by 30 %. Steam at 10 bar, 200 °C has Z = 0.943 (IAPWS-IF97), one reason steam is handled with tables, not pv = RT.

What does the van der Waals equation add to pv = RT?

Two corrections, per mole. The molecules occupy space, so the free volume is v − b. They attract one another, which lowers the pressure on the wall by a/v². Choosing a and b so that the critical isotherm has a flat inflection at the real critical point gives both from Tc and pc alone. For CO2 (NIST: 304.18 K, 73.80 bar) a = 3.656 bar·L²/mol² and b = 0.0428 L/mol. At 320 K and 50 bar vdW predicts Z = 0.785, close to the measured 0.771.

Real gases: van der Waals isotherms, the equal-area rule, compressibility factor and corresponding states: interactive loads as you scroll

What do van der Waals isotherms look like below the critical temperature?

They wiggle: falling, rising, then falling again. The rising part, where pressure grows with volume, is mechanically unstable; a real fluid boils at constant pressure instead. Maxwell's rule places that line so the two lobes it cuts off have equal areas, which is the same as equal Gibbs energy for the liquid and the vapour. At Tr = 0.9 it gives Pr = 0.647, while real CO2 boils at Pr = 0.480: vdW gets the shape right and the numbers only roughly.

What are reduced properties and the generalised compressibility chart?

Divide by the critical values: Tr = T/Tc, Pr = p/pc. The principle of corresponding states says gases at the same Tr and Pr have nearly the same Z, so one chart of Z against Pr, with a line per Tr, serves them all. vdW obeys it exactly (its reduced form has no constants left) but gives Zc = 0.375 for every gas, while NIST data give 0.275 for CO2, 0.290 for N2, 0.288 for CH4 and 0.229 for water. Charts built from measured data do better; the Beattie-Bridgeman equation fits five constants per gas and is more accurate still, at the cost of generality.

Predict, then check

van der Waals predicts the same critical compressibility Zc = pc vc/(R Tc) = 0.375 for every gas. What is the measured value for CO2?

Worked examples

van der Waals constants of CO2 · CO2: Tc = 304.18 K, pc = 73.80 bar, critical density 10.6 mol/l (NIST). R = 8.314462618 J/mol K.
  1. a = 27R²Tc²/(64pc) = 27 × 8.3145² × 304.18²/(64 × 73.80 × 10⁵) = 0.36564 Pa·m⁶/mol² = 3.6564 bar·L²/mol².
  2. b = RTc/(8pc) = 8.3145 × 304.18/(8 × 73.80 × 10⁵) = 42.84 × 10⁻⁶ m³/mol = 0.04284 L/mol.
  3. vdW critical volume = 3b = 0.1285 L/mol; the real one is 1/10.6 = 0.0943 L/mol, so vdW's is 36 % too large.
  4. Zc: vdW pc(3b)/(RTc) = 0.375 exactly; real 0.2753.

Answer: a = 3.656 bar·L²/mol², b = 0.0428 L/mol.

CO2 at 320 K and 50 bar: three answers for v · CO2 at 320 K, 50 bar (Tr = 1.052, Pr = 0.678). NIST reference equation of state: v = 0.41048 L/mol.
  1. Ideal gas: v = RT/p = 8.3145 × 320/(50 × 10⁵) = 0.5321 L/mol.
  2. van der Waals: solve (p + a/v²)(v − b) = RT for the gas root (bisection): v = 0.4179 L/mol, Z = 0.7854.
  3. NIST: v = 0.41048 L/mol, Z = 0.7714.
  4. Errors in v: ideal gas +29.6 %, van der Waals +1.8 %.

Answer: pv = RT is 30 % off; vdW is within 2 %.

How much nitrogen is in a 150-bar cylinder? · A 50-litre cylinder of N2 at 150 bar and 300 K (Tr = 2.38, Pr = 4.41). NIST: v = 0.17056 L/mol.
  1. Ideal gas: v = RT/p = 0.16629 L/mol, so n = 50/0.16629 = 300.7 mol, m = 8.423 kg.
  2. van der Waals (a = 1.367 bar·L²/mol², b = 0.0386 L/mol): v = 0.16205 L/mol, m = 8.643 kg, Z = 0.975.
  3. NIST: n = 50/0.17056 = 293.2 mol, m = 8.212 kg, Z = 1.026.
  4. At this high Tr the repulsion term wins and real N2 has Z > 1; vdW still says Z < 1 and overestimates the mass by 5.3 %, the ideal gas by 2.6 %.

Answer: About 8.21 kg; here vdW (8.64 kg) is worse than pv = RT (8.42 kg).

The vdW boiling pressure of CO2 · CO2 at Tr = 0.9, T = 273.76 K. NIST: the saturation pressure there is 35.419 bar.
  1. Maxwell construction on pr = 8Tr/(3vr − 1) − 3/vr² at Tr = 0.9: Pr = 0.6470, with vr = 0.6034 (liquid) and 2.3488 (vapour).
  2. Check: the area under the isotherm between them equals Pr (vg − vl) = 1.1293 (Simpson).
  3. vdW boiling pressure = 0.6470 × 73.80 = 47.75 bar.
  4. Measured: 35.42 bar (Pr = 0.480). vdW is 35 % high.

Answer: vdW: 47.7 bar, real 35.4 bar: right shape, rough numbers.

Chapter 21

Ideal-gas mixtures: Dalton's and Amagat's laws and mixture properties

Which syllabus covers thisAU ME3391 Unit VVTU BME304 Module 5SPPU not in syllabusMU not in syllabusKTU not in syllabus

How do you describe what is in a mixture: mole fraction or mass fraction?

Either. The mole fraction yi = ni/n counts molecules; the mass fraction xi = mi/m weighs them. They differ because molecules differ in mass: xi = yi·Mi/M. The mixture behaves as one ideal gas with molar mass M = Σ yi·Mi and gas constant R = Ru/M. Dry air (NASA: 78.08 % N2, 20.95 % O2, 0.934 % Ar, 0.042 % CO2 by volume) gives M = 28.97 kg/kmol and R = 0.287 kJ/kg K. By mass the same air is 75.5 % N2 and 23.1 % O2: oxygen molecules are heavier, so oxygen's mass share is larger than its mole share.

What are Dalton's law of partial pressures and Amagat's law of partial volumes?

Dalton: each gas behaves as if it filled the whole volume alone at the mixture temperature; its partial pressure is pi = yi·p and the partial pressures add to p. Amagat: each gas, held alone at the mixture's p and T, would occupy Vi = yi·V, and these volumes add to V. For ideal gases both are exact and say the same thing: pressure and volume shares equal mole fractions. One cubic metre of dry air at 1 atm and 25 °C holds 40.87 mol; its oxygen alone would exert 0.2123 bar, or fill 209 litres at 1 atm. Water vapour condenses when its partial pressure reaches psat at the mixture temperature: that is the dew point.

Ideal-gas mixtures: mole and mass fractions, Dalton's and Amagat's laws, mixture properties and entropy of mixing: interactive loads as you scroll

How do you find cp, γ, u, h and s of a mixture?

Molar cp, u and h are mole-fraction averages; per-kg values are mass-fraction averages. With NIST's ideal-gas cp for each gas at 25 °C, dry air has cp = 1.0047 kJ/kg K and γ = cp/(cp − R) = 1.3999, the familiar 1.005 and 1.4. Entropy is different: each gas is evaluated at its own partial pressure, s̄i(T, yi·p), so the mixture's entropy is more than the sum at the full pressure. Because cp of CO2, H2O and CH4 rise with temperature, a mixture's γ falls as it gets hotter.

Why does mixing two gases generate entropy, even with no temperature difference?

Remove a partition between two different gases at the same T and p: nothing heats or cools, the pressure stays the same, yet each gas expands into the whole volume, its partial pressure falling from p to yi·p. Each gas's entropy rises by −R ln yi per mole, so ΔS = −Ru Σ ni ln yi > 0. For 1 m³ of N2 and 1 m³ of O2 at 1 bar and 25 °C this is 0.465 kJ/K, and unmixing them needs at least T0·ΔS of work. If the two sides hold the same gas the term vanishes: nothing distinguishes the molecules (Gibbs' paradox).

Predict, then check

Two 1 m³ halves of an insulated rigid tank hold N2 and O2, both at 1 bar and 25 °C. You pull out the partition. What happens to the total entropy?

Worked examples

Dry air as one gas · Dry air by volume (NASA): 78.08 % N2, 20.95 % O2, 0.934 % Ar, 0.042 % CO2 (normalised to 100 %); M from the NIST WebBook; ideal-gas cp at 25 °C from the NIST Shomate fits
  1. The rounded shares add to 100.006 %, so divide each by 1.00006
  2. M = Σ yi·Mi = 0.78075 × 28.0134 + 0.20949 × 31.9988 + 0.00934 × 39.948 + 0.00042 × 44.0095 = 28.966 kg/kmol
  3. R = 8.314/28.966 = 0.287 kJ/kg K
  4. Mass fractions xi = yi·Mi/M: N2 75.51 %, O2 23.14 %, Ar 1.29 %, CO2 0.064 %
  5. Molar cp = Σ yi·c̄pi = 29.104 kJ/kmol K, so cp = 29.104/28.966 = 1.0047 kJ/kg K and γ = 29.104/(29.104 − 8.314) = 1.3999

Answer: M = 28.97 kg/kmol (NASA quotes 28.97), R = 0.287 kJ/kg K, cp = 1.005 kJ/kg K, γ = 1.4

Flue gas of a methane burner and its dew point · CH4 burnt completely with 20 % excess air, air taken as 20.95 % O2 and 79.05 % N2 (argon lumped with nitrogen); products at 1 atm
  1. CH4 + 2O2 → CO2 + 2H2O; with 20 % excess the air supplies 2.4 mol O2 and 2.4 × 79.05/20.95 = 9.056 mol N2 per mol CH4
  2. Products: 1 CO2 + 2 H2O + 0.4 O2 + 9.056 N2 = 12.456 mol
  3. Mole fractions: N2 72.7 %, H2O 16.06 %, CO2 8.03 %, O2 3.21 %; M = 27.82 kg/kmol
  4. Partial pressure of the vapour (Dalton): pv = 0.16057 × 1.01325 = 0.1627 bar
  5. Dew point = Tsat at 0.1627 bar (IAPWS-IF97) = 55.7 °C. At 25 °C psat is only 0.0317 bar, so cooling the flue gas to room temperature condenses most of the water

Answer: 16.1 % water vapour by mole, dew point 55.7 °C

Mixing two gases at different states · Insulated rigid tank, two 1 m³ halves: A = N2 at 1 bar, 25 °C; B = CO2 at 3 bar, 200 °C. Partition removed. Ideal gases, NIST cp(T)
  1. nA = pV/RuT = 10⁵/(8.314 × 298.15) = 40.34 mol; nB = 3 × 10⁵/(8.314 × 473.15) = 76.26 mol
  2. Energy: Q = 0 and W = 0 (rigid), so ΔU = 0: nA·∫cv,N2 dT + nB·∫cv,CO2 dT = 0, with cv = cp − Ru
  3. Solving with temperature-dependent cv (fixed-point iteration on the mean cv of each gas): Tf = 157.84 °C
  4. pf = (nA + nB)·Ru·Tf/2 m³ = 2.0891 bar; yN2 = 0.346
  5. ΔS = Σ ni[∫cp dT/T − Ru ln(yi·pf/pi)] = 0.7347 kJ/K, of which the mixing term −Ru Σ ni ln yi is 0.6252 kJ/K

Answer: Tf = 157.8 °C, pf = 2.089 bar, ΔS = 0.735 kJ/K (mixing alone 0.625 kJ/K)

Chapter 22

Thermodynamic relations: Helmholtz and Gibbs functions, Maxwell relations, cp − cv

Which syllabus covers thisAU ME3391 Unit VVTU BME304 Module 5SPPU not in syllabusMU MEC305 Module 3KTU not in syllabus

What are the Helmholtz and Gibbs functions for?

The Helmholtz function a = u − Ts and the Gibbs function g = h − Ts are properties built from u, h, T and s. With the book's sign convention (work done by the system positive), the work a system can do at constant temperature is at most the drop in a, and the useful work at constant T and p is at most the drop in g. They also give the equilibrium rules: at fixed T and p a system settles at minimum g, which is why boiling water and its vapour have equal g, and that equality leads straight to the Clapeyron equation of chapter 24.

Where do the Maxwell relations come from, and why are they useful?

Each of u, h, a and g has an exact differential: du = T ds − p dv, dh = T ds + v dp, da = −s dT − p dv, dg = −s dT + v dp. For an exact differential the mixed second derivatives are equal, and that gives one Maxwell relation from each. Their value is that entropy cannot be measured directly, while p, v and T can: (∂s/∂v)T is replaced by (∂p/∂T)v, which an equation of state gives. For steam at 300 °C and 10 bar both sides of the first relation below are 1.8737 kPa/K by finite differences on IAPWS-IF97.

Maxwell relations checked numerically on steam and a van der Waals gas, cp - cv and the energy equation: interactive loads as you scroll

Why is cp − cv = R for an ideal gas, and what is it for a liquid?

Combining the Tds equations with the Maxwell relations gives cp − cv = T·v·β²/κT, where β is the volume expansivity and κT the isothermal compressibility. Since κT > 0, cp ≥ cv always. For an ideal gas β = 1/T and κT = 1/p, so cp − cv = pv/T = R: Mayer's relation. Liquid water at 50 °C and 10 bar (IF97) has β = 4.57 × 10⁻⁴ per K and κT = 0.439 × 10⁻⁶ per kPa, so cp − cv = 0.156 kJ/kg K, under 4 % of its cp. At 3.96 °C, where water is densest, β = 0 and cp = cv exactly.

What does the energy equation (∂u/∂v)T = T(∂p/∂T)v − p tell you?

It gives how internal energy changes with volume at constant temperature from p-v-T data alone. For an ideal gas p = RT/v, so T(∂p/∂T)v = p and the right side is zero: u depends on T only, which is what Joule's free-expansion experiment showed. For a van der Waals gas the right side is a/v²: pulling molecules apart against their attraction stores energy. CO2 at 400 K and 50 bar (van der Waals, a and b from chapter 20) has v = 13.49 litres/kg and (∂u/∂v)T = 1037 kPa, so expanding it isothermally needs heat for this energy as well as for the work.

Predict, then check

Liquid water at 1 bar has its maximum density near 4 °C. What is cp − cv there?

Worked examples

Checking a Maxwell relation on steam · Superheated steam at 300 °C and 10 bar, IAPWS-IF97 region 2; five-point finite differences
  1. v = 0.25798 m³/kg
  2. Left side, along the isochore: find the pressure that keeps v fixed at 299.9, 299.95, 300.05 and 300.1 °C (bisection), then (∂p/∂T)v = 1.87372 kPa/K
  3. Right side, along the 300 °C isotherm: (∂s/∂v)T = (∂s/∂p)T ÷ (∂v/∂p)T = 1.87372 kPa/K
  4. Ideal gas at the same v: R/v = 0.4615/0.25798 = 1.789 kPa/K; the real value is 4.7 % higher

Answer: Both sides 1.8737 kPa/K: the relation holds to the precision of the differences

cp − cv of liquid water · Water at 50 °C and 10 bar, IAPWS-IF97 region 1
  1. v = 1.0117 × 10⁻³ m³/kg; (∂v/∂T)p = 4.626 × 10⁻⁷ m³/kg K, so β = 4.573 × 10⁻⁴ per K
  2. (∂v/∂p)T = −4.443 × 10⁻¹⁰ m³/kg kPa, so κT = 0.4392 × 10⁻⁶ per kPa
  3. cp − cv = T·v·β²/κT = 323.15 × 0.0010117 × (0.0004573)² / 0.0000004392 = 0.1557 kJ/kg K
  4. Direct check: cp = (∂h/∂T)p = 4.1775, cv = (∂u/∂T)v = 4.0218, difference 0.1557 kJ/kg K

Answer: cp − cv = 0.156 kJ/kg K (cp = 4.177, cv = 4.022); a third of R for steam

A van der Waals gas: energy equation and cp − cv · CO2 as a van der Waals gas, Tc = 304.18 K, pc = 73.80 bar (NIST), R = 8.314/44.01 kJ/kg K; state 400 K, 50 bar
  1. R = 0.18892 kJ/kg K, a = 27R²Tc²/(64pc) = 0.18878 kPa m⁶/kg², b = RTc/(8pc) = 0.9734 × 10⁻³ m³/kg
  2. Solve 5000 = RT/(v − b) − a/v² by bisection: v = 13.49 × 10⁻³ m³/kg, Z = pv/RT = 0.8926
  3. (∂u/∂v)T = T(∂p/∂T)v − p = TR/(v − b) − p = a/v² = 1037.3 kPa
  4. cp − cv = −T(∂p/∂T)v²/(∂p/∂v)T = 0.2774 kJ/kg K, against R = 0.1889 for the ideal gas

Answer: (∂u/∂v)T = 1037 kPa (zero for an ideal gas); cp − cv = 0.277 kJ/kg K, 47 % above R

Chapter 23

The Joule-Thomson coefficient and the inversion curve

Which syllabus covers thisAU ME3391 Unit VVTU BME304 Module 5SPPU not in syllabusMU MEC305 Module 3KTU not in syllabus

What is the Joule-Thomson coefficient?

Push a gas steadily through a porous plug or a nearly closed valve, with no heat and no work. The steady-flow energy equation then gives h2 = h1: throttling is isenthalpic. How the temperature changes with the pressure drop is the Joule-Thomson coefficient μ = (∂T/∂p)h. Positive μ means the gas cools as the pressure falls. Nitrogen at 300 K and 1 bar has μ = 0.212 K/bar (NIST), so a 10 bar drop near room conditions cools it by about 2 K. Using a Maxwell relation, μ follows from p-v-T data and cp alone.

Why does an ideal gas not change temperature on throttling, while a real gas does?

For an ideal gas v = RT/p, so T(∂v/∂T)p = v and μ = 0: h depends on T only. In a real gas two effects compete. Attraction between molecules means that as they spread apart they slow down, and the gas cools. Their finite size works the other way. At low pressure μ ≈ (T·dB/dT − B)/cp, with B the second virial coefficient. For van der Waals B = b − a/RT, which gives μ ≈ (2a/RT − b)/cp, so cooling below an inversion temperature 2a/(Rb) = 6.75·Tc: 852 K for N2, against 607 K from NIST data.

What is the inversion curve, and how good is a cubic equation of state at predicting it?

Join every state where μ = 0 and you get the inversion curve. Inside it throttling cools the gas; outside, it warms it. The isenthalps peak on it. The figure uses the Peng-Robinson equation, a model better than van der Waals but still a model. For N2 it puts the curve's highest pressure at 446 bar, while NIST data give about 391 bar. Its low-pressure inversion temperature is 642 K against 607 K, and it gives μ = 0.26 K/bar at 300 K and 1 bar against 0.212. The shape is right; the numbers are 5 to 20 % off.

The Joule-Thomson effect: throttling a real gas, the inversion curve and why hydrogen warms up: interactive loads as you scroll

Why do hydrogen and helium warm up when throttled at room temperature?

Their molecules attract each other very weakly, so their inversion temperatures are low: NIST data put the low-pressure inversion at 201 K for hydrogen and 45 K for helium. At 300 K both lie outside the curve and warm on throttling (μ = −0.0303 and −0.0629 K/bar). To liquefy them by throttling (the Linde process) they must first be precooled below inversion, for example with liquid nitrogen, which boils at 77.4 K. These quantum gases also break the usual Peng-Robinson recipe: with their negative acentric factors it predicts that hydrogen cools at 300 K, so the model here uses κ for ω = 0.

Predict, then check

Hydrogen at 300 K and 150 bar is throttled to 1 bar through a valve. What happens to its temperature?

Worked examples

μJT of nitrogen: model against data · N2 at 300 K and 1 bar; Peng-Robinson with Tc = 126.192 K, pc = 33.958 bar, ω = 0.0372 (NIST); ideal-gas cp from the NIST Shomate fit; NIST μ = 2.11967 K/MPa
  1. μ = −(∂h/∂p)T/(∂h/∂T)p, with h = ∫cp0 dT + the Peng-Robinson enthalpy departure, evaluated by central differences
  2. Model: μ = 0.2597 K/bar
  3. NIST: 2.11967 K/MPa = 0.212 K/bar, so the model is 23 % high
  4. Throttling from 10 bar to 1 bar at 300 K: the model's isenthalp ends at 297.7 K, a drop of 2.3 K

Answer: Model 0.26 K/bar against NIST 0.212 K/bar; about 2 to 2.5 K of cooling for a 10 bar drop

A large pressure drop: integrate along the isenthalp · N2 from 300 K, 200 bar throttled to 1 bar; Peng-Robinson model; NIST: h(300 K, 200 bar) = 7.81882 kJ/mol equals h(1 bar) at 269.19 K
  1. Inlet: h1 = −1017.2 J/mol relative to the ideal gas at 300 K (departure −1017.2 J/mol, checked by integrating (v − T∂v/∂T) dp)
  2. Outlet: solve h(T2, 1 bar) = h1 by bisection: T2 = 265.4 K, ΔT = −34.6 K
  3. Data: the NIST tables give T2 = 269.19 K, ΔT = −30.8 K
  4. Using the 1 bar μ for the whole 199 bar drop would give −42 K: μ shrinks at high pressure, so integrate the isenthalp instead

Answer: The gas cools by about 31 K (NIST data); the Peng-Robinson model says 35 K

Inversion temperatures of four gases · Low-pressure limit; Peng-Robinson from NIST critical constants and acentric factors (H2 and He with κ for ω = 0); NIST inversion temperatures read where the tabulated μ changes sign at 1 bar
  1. Condition: T·dB/dT = B, with the model's second virial coefficient B = b − a(T)/RT; solved by bisection
  2. N2: model 642 K, NIST 607 K; CO2: model 1168 K (above the 1,100 K range of the NIST CO2 data)
  3. H2: model 182 K, NIST 201 K; He: model 28.5 K, NIST 45.3 K
  4. Standard Peng-Robinson with hydrogen's ω = −0.219 would give μ = +0.013 K/bar at 300 K: the wrong sign

Answer: Room temperature is inside the cooling region for N2 and CO2 and outside it for H2 and He; the model is closest for CO2 and furthest off for He

Chapter 24

The Clapeyron and Clausius-Clapeyron equations

Which syllabus covers thisAU ME3391 Unit VVTU BME304 Module 5SPPU not in syllabusMU MEC305 Module 3KTU not in syllabus

What does the Clapeyron equation say?

Along a phase boundary the two phases have equal Gibbs function. Moving along the boundary keeps them equal, which gives the slope below: hfg is the latent heat and vfg the volume change. It is exact thermodynamics, so measuring psat(T) gives the latent heat. Water at 100 °C: dp/dT = 3.6192 kPa/K and vfg = 1.6708 m³/kg give hfg = 373.15 × 1.6708 × 3.6192 = 2256.4 kJ/kg, against 2256.5 kJ/kg from IAPWS-IF97. Between 1 and 350 °C the two differ by at most 0.015 %.

What extra approximations turn it into the Clausius-Clapeyron equation, and how good are they?

Neglect the liquid volume (vfg ≈ vg), treat the vapour as an ideal gas (vg = RT/p) and hold hfg constant. Then d(ln p)/d(1/T) = −hfg/R: ln p against 1/T is a straight line. Anchored at a known point with that point's hfg, it predicts psat 50 K away to within 0.2 % from 100 °C, 3.5 % from 50 °C and 8.6 % from 200 °C, where the vapour is far from ideal and hfg is falling. Good for a quick estimate; use steam tables for design.

The Clapeyron equation: the slope of the boiling curve gives the latent heat; Clausius-Clapeyron vs IAPWS-IF97: interactive loads as you scroll

How do a pressure cooker and high altitude change the boiling point?

The boiling point is Tsat at the surrounding pressure. A cooker whose weight valve holds 1 bar above atmospheric (illustrative) boils water at 120.4 °C (IF97), so food cooks faster. At altitude the air pressure falls: the standard atmosphere gives 65.8 kPa at 3,500 m, about the height of Leh, where water boils at 88.3 °C. The Clausius-Clapeyron line through 100 °C gives 120.6 °C and 88.1 °C, close to both.

Why does pressure lower the melting point of ice?

Ice is less dense than liquid water: 916.7 against 999.8 kg/m³ at the triple point (IAPWS). So vf − vi is negative, and with a positive latent heat of 333.4 kJ/kg the Clapeyron slope is negative: −13.47 MPa/K. Squeezing ice favours the denser liquid. The effect is small: 100 bar lowers the melting point by only 0.743 K by Clapeyron's straight line, and by 0.758 K on the IAPWS melting curve. For most substances the solid is denser and the slope is positive.

Predict, then check

Ice at 0 °C is squeezed to 100 bar. Roughly how much does its melting point change?

Worked examples

Latent heat from the slope of the boiling curve · Water at 100 °C; psat(T) from IAPWS-IF97 region 4, vf and vg from regions 1 and 2
  1. psat(100 °C) = 101.418 kPa; dp/dT by a five-point difference with ±1 mK steps = 3.61919 kPa/K
  2. vf = 0.0010435, vg = 1.67186, so vfg = 1.67082 m³/kg
  3. hfg = T·vfg·dp/dT = 373.15 × 1.67082 × 3.61919 = 2256.44 kJ/kg
  4. IF97 hg − hf = 2256.47 kJ/kg: the difference is −0.0014 %

Answer: hfg = 2256.4 kJ/kg from the slope, 2256.5 kJ/kg from the tables

Boiling in a pressure cooker and in Leh · Atmosphere 101.325 kPa; cooker valve at 1 bar gauge (illustrative); Leh at about 3,500 m in the standard atmosphere p = 101.325(1 − 0.0065z/288.15)^5.2559 kPa
  1. Cooker: p = 201.325 kPa; Tsat by bisection on IF97 psat = 120.42 °C
  2. Leh: p = 101.325 × (1 − 0.0065 × 3500/288.15)^5.2559 = 65.76 kPa; Tsat = 88.3 °C
  3. Clausius-Clapeyron from the normal boiling point (IF97: 99.97 °C at 1 atm, hfg = 2256.5 kJ/kg): 1/T = 1/T0 − (R/hfg)·ln(p/p0)
  4. gives 120.61 °C in the cooker and 88.06 °C in Leh

Answer: 120.4 °C in the cooker, 88.3 °C in Leh; the straight-line estimate is within 0.2 K

The melting line of ice · Triple point 273.16 K, 611.657 Pa; ice ρ = 916.709 kg/m³ and h = −333.444 kJ/kg relative to the liquid (IAPWS R10-06); liquid v from IF97
  1. vf = 1.00021 × 10⁻³, vi = 1/916.709 = 1.09086 × 10⁻³ m³/kg; vf − vi = −90.65 × 10⁻⁶ m³/kg
  2. Latent heat of melting = 333.445 kJ/kg
  3. dp/dT = 333445 ÷ (273.16 × −90.65 × 10⁻⁶) = −13.466 MPa/K; the IAPWS R14 melting curve has −13.466 MPa/K at the triple point
  4. At 100 bar: straight line ΔT = −0.743 K; IAPWS melting curve −0.758 K

Answer: Slope −13.47 MPa/K; 100 bar lowers the melting point by 0.76 K

Keep going

Recommended reading

  • Engineering Thermodynamics, P. K. Nag
  • Thermodynamics: An Engineering Approach, Y. A. Cengel and M. A. Boles
  • Fundamentals of Engineering Thermodynamics, M. J. Moran, H. N. Shapiro, D. D. Boettner and M. B. Bailey
  • Fundamentals of Thermodynamics, C. Borgnakke and R. E. Sonntag
  • Engineering Thermodynamics: Fundamentals and Applications, E. Natarajan
  • Basic Thermodynamics, B. K. Venkanna and S. B. Wadavadagi
  • Heat and Thermodynamics, M. W. Zemansky and R. H. Dittman

How this book was made

Chapters follow the official syllabi listed above. Every interactive's formulas and every worked-example number were checked by script. Explanations, animations and examples are original to Skill-Lync. Topics informed by MIT OpenCourseWare 2.005 (Thermal-Fluids Engineering I), CC BY-NC-SA. All explanations, animations and examples are original to Skill-Lync; MIT does not endorse this page.

From the exam to a core job

Talk to a counsellor.

Ask how thermal and CFD engineers use engineering thermodynamics on real projects, and what the Foundations of Thermodynamics and its Industrial Applications covers.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.