Wiring harness routing & packaging Rules Week 3 Challenge

Aim: Route the harness on Given car body and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required.   Design Considerations: 1.Routing shall provide enough slack for each branch…

AIM To create the back door design with necessary reinforcement and embosses (Hinge, gas stay, wiper motor, striker) using given class A surface and to do draft analysis for the parts. PARTS IN BACK DOOR Back door is a closure used for access the boot spce of the car and it is also used to protect forign particle to enter…

AIM  To create an asembly by developing the essential flanges for the outer and creating front roof rail, rear roof rail, bow roofs, center roof rail, and to do a curvature study on the roof and perform calculation to determine the position of the bow roofs.      REASONS FOR CREATING ROOF RAILS …

AIM To create the baffle mounting, sill mounting, bumper mounting, pillar mounting, drip area mounting according to the given master scetion of the given class A surface.   FENDER  Fenders is located extremely close together on a car but they have very different functions and appearances. Appearance: Fenders…

    Come up with a new section that has an improved Section Modulus compared to the previous one and mention what changes you made which resulted in the increased strength.   Refer the grading policy    The report is to be made available in the Answer box provided below Your Answers SECTION MODULUS…

AIM To create a Hood Design which includes a detailed explanation about hood and its components, Latch Trajectory, Mastic Data, Emboss Definitions, Manufacturing process like Deep-Drawing and Hemming, and all the parameters followed in the design. DESIGN DATA GIVEN Inner panel thickness = 0.75mm Outer panel…

AIM Route the harness on given V-16 engine and prepare flatten view. Apply all packaging rules and industry best practices for the given engine. Engine harness An engine wiring harness is constricted wires, cables, terminals, and connectors controlling a vehicle’s electrical system. It relays electrical power and…

AIM: TO FLATTEN THE WIRING HARNESS AND DRAFT THE WIRING HARNESS ASSEMBLY. GIVEN: HARNESS ASSEMBLY: HARNESS FLATTENING: WE GO TO THE HARNESS FLATTENING WORKBENCH AND DEFINE THE FLATTENING PARAMETERS. WE USE THE EXTRACT COMMAND TO BRING THE HARNESS ASSEMBLY TO THE FLATTENING WORKBENCH HERE. CHOOSING A SUITABLE PLANE WE FLATTEN…

Aim: Route two electrical harnesses per the given layout and interconnect them as a single harness assembly check for bundle continuity, and bundle warnings, and then provide annotations for the final harness assembly. Objective: The objective of this project is to first route the two Harness A and Harness B as per the…

  Aim:  1) To Route the following harness layout in the Electrical workbench. 2) Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Given: CAD data of the following Connectors:  DT06-4S DT06-6S DT06-2S DT06-08SA Connectors Layout Design: Steps to be followed: 1. Download…

 Wiring harness routing & packaging Rules Week 3 Challenge Q1. Download following clip cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. Hellarmann Tyton – 21160129 process: Create two points one as entry and another as exit point.…

Wiring harness design in CATIA V5 - 3D modeling Week 2 Challlenge AIM:  Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip. Deutsch DT06 – 08SA…

 REPORT ON UNDRBODYCOATING Underbody coating - Underbody coating is usually a dense cladding (often based on rubber) applied uniformly to the undercarriage of the automobile. It is normally sprayed or painted on when the car is just out of the dealership and is clean. But even if you are getting the undercoating…

BENCHMARKING Benchmarking is a process of measuring the performance of a company’s products, services, or processes against those of another business considered to be the best in the industry, “best in class.” The point of benchmarking is to identify internal opportunities for improvement. By studying…

Attachment Feature Creation (Ribs & Screw Boss) 

Week 8 - Challenge 4 - Bumper

Week 9 - Project - A pillar Design with Master Section

Week 8 - Challenge 6 - Core & Cavity Design

Week 8 - Challenge 3 - Coin Holder Design

Week 8 - Challenge 2 - Switch Bezel Design

Week 8 - Challenge 1 - Base Bracket Design