Wiring harness design in CATIA V5 - 3D modeling Week 7 Challenge

MY NAME - ABHISHEK VERMA CHALLENG NAME -BOX ASEEMBLY.Objective-:)The goal of this challenges is to use UG NX Sheet Metal application where we prioritize the tools .we use to build Box Assembly. Introduction-:) Sheet Metal is Metal formed thin ,flat pieces by an industrial process .Sheet Metal is one of the Fundamental…

MY NAME - ABHISHEK VERMA CHALLENGES NAME - CASING -DESIGN..Introduction:-I am start tutorial casing design , Sheetmetal step by step and using software SIEMENS NX SHEETMETAL......

                                                ROOF  DESIGN THEORYAim: Design of the front roof rail, rear roof rail, and bow roof for the roof of the vehicles with the help of the given skin data of the roof according to snow load condition and hear distortion criteria.Objective:Study different type of the roof available…

 AUTOMOTIVE WIRING HARNESS FOR BACKDOOR       Aim: To route the wiring harness on the given backdoor assembly and prepare the flatten view drawing in CATIA V5.   Objective: The objective of this project is to route the wiring harness and prepare flatten view drawing for the Backdoor of the car. All types of packaging rules…

AIM- Routing for side door panel Route the wire for the side door of a care with the necessary connector along with the guiding challenge data given  TASK  Routing assembly creation  Flattening  Drawing creation. A door wiring harness is a device made of insulating material, such as rubber or vinyl, to enclose wires in…

AIM:TO FLATTEN THE WIRING HARNESS AND DRAFT THE WIRING HARNESS ASSEMBLY.GIVEN:FLATTENING:WE GO TO THE HARNESS FLATTENING WORKBENCH AND DEFINE THE FLATTENING PARAMETERS.WE USE THE EXTRACT COMMAND TO BRING THE HARNESS ASSEMBLY TO THE FLATTENING WORKBENCH HERE.CHOOSING A SUITABLE PLANE WE FLATTEN THE HARNESS ASSEMBLY.BUNDLE…

                                           Wiring harness design in CATIA V5 - 3D modelling Week 5 & 6 Challenge Aim: Route two electrical harnesses per the given layout and interconnect them as a single harness assembly check for bundle continuity, and bundle warnings, and then provide annotations for the final harness…

   Aim:    1) To Route the following harness layout in the Electrical workbench.   2) Add protective covering on all branches connected to DT06-2S & DT06-4S connectors.   Given:   CAD data of the following Connectors:    DT06-4S   DT06-6S   DT06-2S   DT06-08SA   Connectors Layout Design:     Steps to be followed:   1.…

                                                                                     Wiring harness routing & packaging Rules       Download following cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. P clamp   process: Create two points one as entry…

                                                 WIRING HARNESS DESIGN IN CATIA V5   AIM-:Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip.   Deutsch DT06 – 08SA ( https://www.te.com/usa-en/product-DT06-08SA.html)…

                                                                     - Design of Backdoor -   Objective:  To design Back door of car using the given Class ‘A’ surface.                               It is a hinged board or door at the rear of the vehicle that can be moved up or down during loading and unloading. Back Door…

OBJECTIVE- To develop the front fender using Nx cad following the design parameters. Mounting Area Bumper Drip A Pillar Sill Baffel Introduction: Fender: Fender is a part of the vehicle that frames the wheel . The primary purpose of the fender is to prevent sand , mud , rock etc from being thrown away into the air by rotating…

Aim: To find the section modulus of the hood and optimization to improve the overall section modulus.   Objective: Use the section from your Hood design and calculate the section modulus using the formula S= I/y. Section Modulus: The section modulus (S) is geometry property of the cross section used for designing beams…

AIM:=        Design Hood Outer Panel, Inner Panel and the necessary reinforcements by following the Master Section mentioned with the Design parameters explained in the videos. Objectives:= Submit an ASSEMBLY of Hood Inner Panel, Outer Panel, Latch, Hinge and the Reinforcements.A detailed report about the Hood Design which…

                         -   NOTE: I have Attached the Report, Photos and CADpart in the Attachment.- OBJECTIVES Create the Door trim Panel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class…

                                                                      -  A pillar Design with Master Section- AIM:-      …

DESIGN OF THE DOOR TRIM LOWER WITH ENGINEERING FEATURES INCLUS HEAT STAKES,LOCATORS & RIBS  Aim: To design the door trim lower component from the given class A surface and create the engineering features ( heat stakes and locators ) on the component using CATIA V5  software Objectives:  Creation…

                                                  Dog House Design for the Door Trim..     Aim :       Create the Dog House for the Door Trim considering the design rules and perform the draft analysis for class A and create the final close body component and perform the draft analysis.   Objective : Create the Tooling…

Ribs and Screw Boss creation    Aim :    To create the Rib for the drill handle considering the design rules for rib creation and Screw boss creation and then perform the Draft analysis for the final component. Objective : Create the Tooling axis by using the bisecting method. Design the class-B and…

DESIGN OF BUMPER USING CLASS A SURFACE-: AIM: Design the bumper of a car( part ) using class A surface provided in CATIA sotfware OBJECTIVE-: The main objective is to make use of the class A surface provided and generate the class B and class c surfaces and there by joining /trimming of the them leads to the…

DESIGN AND DRAFT ANALYSIS OF SWITCH BEZEL OBJECTIVE The objective of the project is to design the switch bezel and to do a draft analysis for it by creating the required tooling direction with the help of Bisecting method. INTRODUCTION The control panel bezel is the frame part of the window switch that holds its switch…

Base Bracket Design:- AIM:  to make a model from the provided class-A surface. INTRODUCTION: CLASS-A SURFACE: a surface made by the designer which is given as an input to the plastic modeler to work on. It is aesthetic surface and the outer most surface. CLASS-B SURFACE: a surface below a certain thickness from the…

QUS-1 /ANS -:       QUSNO-2/ ANSWER -: