Week 8 - Challenge 6 - Core & Cavity Design

  Aim: To decide wether the design is whether the european standards or not.   Given design:  WHEEL ARCH:The wheel arch is the semicircular part positioned above the wheel of a vehicle. The most important body change was that the front wheel arch was cut higher into the fender. Corrosion had occurred around…

Introduction: Hood The Hood is the outer panel covering the front engine of the vehicle. It opens to allow access to the engine compartments for the ease of maintenance or repair of the vehicle. Hood is also considered as another door as it consists of the outer panel, an inner panel like side doors of a vehicle. Outer…

UNDERBODY COATING   Underbody Coating is a sprayable coating, which protects the under surface of the vehicle from corrosion. Underbody coating provides long term protection from corrosion to car's underbody. It also protects parts like internal body panels, frame rails and other inner cavities that are…

AIM: DETAILED REPORT ON BENCHMARKING To prepare a report explaining what is Bench-marking , Compare at least 4 Vehicles and Provide a Preoper conclusion for the report ,suggesting a suitable vehicle among the comparison made. WHAT IS BENCHMARKING ? It is the process of comparing one's business process and performance…

AIM: To create a door interior part from the inputs of class A surface along with master section by following the design rules followed in tier 1 and OEM industries in CATIA v5 OBJECTIVES: Create a sketch by using a Positioned sketch All the should be sketching should be 'so-Constrained Ensured Proper Tree Structure Geometrical…

Design and Assembly of Butterfly Valve by applying GD&T using NX-Cad Objective The objective of this project is to model a butterfly valve and apply GD&T to the different parts then assemble all parts together by applying required constraints. Introduction A butterfly valve is a quarter-turn rotational motion…

Week 9 - Project - A pillar Design with Master Section OBJECTIVES: To create the class B and class C surfaces from the given class A surface To form a solid geometry by combining all the surfaces To create a dog house for the solid part whilst following the design rules To perform draft analysis on the class A surface…

Objective: The main aim of this challenge is to create a solid body of 'Door Trim Lower' with the help of the closed surface method by using the 'Generative shape design' workbench in CATIA V5. Performing the 'Draft Analysis' on the solid part body of the Door trim. Given sample design Overview:Initially, we need…

Dog house design for the Door Trim:   Aim: Create the Dog House for the Door Trim considering the design rules and perform the draft analysis for class A and create the final close body component and perform the draft analysis. Objective: Create the Tooling axis  Design the class-B and class-C surfaces and…

DOOR HANDLE :- AIM: To Create the Door Handle Component from the given Class-A surface. To Create the tooling axis for the given Class-A Surface meeting the requirements of the draft angle. To Attach B side Features in the component. To perform the Draft analysis on the model. Class A surface: Class A surface is a…

Core & Cavity Design Objective- To Create the Core and cavity blocks for the switch bezel . Aim- Tree Structure Tooling Axis Switch Bezel Solid / Surface body Parting Line and Parting Surface To ensure Proper Tree Structure Geometrical sets with a proper name based on the sketches present inside of it All the…

BUMPER DESIGN :- Aim- Create the Bumper Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.    Class A Surface- Class A Surface…

TO DESIGN A COIN HOLDER BY USING CLASS A SURFACE  AIM:  To design a coin holder Plastic component through the given Class-A surface by creating a tooling axis and draft analysis of the given surface. Raw material used:          DESIGN PROCEDURE:  To setup the class-A surface and…

DESIGN AND DRAFT ANALYSIS OF SWITCH BEZEL  Aim: This project aims to create a switch bezel plastic component using the given class A surface following the OEM standard. and perform the draft analysis. SWITCH BEZEL:  The control panel bezel is the frame part of the window switch that holds its switch covers…

Aim: To create the Base Bracket of Plastic Component through a given input Class A Surface and Tooling axis to Draft Analysis on the A surface and  final plastic component. Base bracket:   Its is used in bonet. Raw material used in base bracket of plastic component: * Thermosetplastic    Class…

.