Week 8 - Challenge 6 - Core & Cavity Design

AIM :- To create a CAD model for door trim panel's parts by considering the given inputs of class A surface along with master section by following the design rules followed in OEM and tier1 companies.   Objectives :-   To create individual tooling axis for the parts and perform draft analysis on the class A surface To…

  AIM : To create a body of Bumper from the input given which was the A-surface of a Bumper. The created body should be a closed solid volume which should be feasible for manufacturing and Tooling. The draft angle and draft analysis of the component should be done. In model, proper tree structure to be maintained and publications…

AIM Create the Dog House for the Door Trim considering the design rules INTRODUCTION DOG HOUSE Dog house is an engineering feature used in plastic design. Dog houses are used as support feature. Sometimes other engineering features like snaps, locators, and screw bosses are mounted on them to increase their strength. Dog…

BACK DOOR:                   * An automobile back door or tailgate is the panel thet covers of an automobile .it enables access to the main luggage compartment .a hinge allows the boot lid to be raised,while devices such as springs or gas cylinder hold it up in the…

  AIM:       * To plot graphs based on the studies done on genetic algorithm OBJECTIVE :    *To study about the genetic algorithim and stalagmite function. To plot graphs based on the studies done for genetic algorthim    THEORY:        * The algoritham begins…

AIM :        To write a program in matlab to simulate the forward kinematic of a 2R robotic arm  OBJECTIVE:        Animating and creating a movie from the plots obtained from the program. THEORY:           A maipulator end effector movement determines…

AIM: To Create the Door Handle Component from the given Class-A surface. To Create the tooling axis for the given Class-A Surface meeting the requirements of the draft angle. To Attach B side Features in the component. To perform the Draft analysis on the model.  TOOLS USED: Boundary Join Multiple extract Bisecting…

AIM : Create the Assembly of given 2 Mechanisums. Observation : First create all parts in Part work bench then take the all part in assembly then make constrain them. Once make constrain then check it with Explode view where all parts are constrains properly. Below Snaps are shown the preparation of assembly.…

NOTE: BOTH CAT PART AND PPT IS IN THE ZIPPED FILE 3D CAD 3D Model of A Piller with attachment feature A PILLER WITH DOGHOUSE CLASS A SURFACE DETAILED TREE STRUCTURE SKETCH ANALYSIS The geometry tab of sketch solving status for each drawing. TOOLING AXIS The Primary Tooling Axis was obtained with the…

Objective: The main aim of this challenge is to create a solid body of 'Door Trim Lower' with the help of the closed surface method by using the 'Generative shape design' workbench in CATIA V5. Performing the 'Draft Analysis' on the solid part body of the Door trim. Overview:Initially, we need to offset the given…

Aim/Objectives: Create the Core and cavity blocks for the switch bezel designed in the earlier challenge. Steps Followed: Tooling Axis creation Checking Draft analysis for created tooling Axis Creating parting Surface Creating Core Side Creating cavity side. 1). Tooling Axis: Tooling axis is the axis in which core cavity…

COIN HOLDER To create a coin holder plastic component by closed method with reference to the class A surface and do the draft analysis for the component. Steps followed The class A surface is checked for the connectivity of the surface and ensure it is completely joined and there will be no gap between the surfaces. If…

  DESIGN AND DRAFT ANALYSIS OF SWITCH BEZEL OBJECTIVE The objective of the project is to design the switch bezel and to do a draft analysis for it by creating the required tooling direction with the help of Bisecting method. INTRODUCTION The control panel bezel is the frame part of the window switch that holds its…

AIM:  Design a Base Bracket Plastic component through the given Class-A surface  DESIGN PROCEDURE:  Creating a tooling axis in class A surface. To perform draft analysis. To create a B-surface.  To create a C-surface.  To create solid part model.      Creating a tooling axis in class…

  AIM:                    * To develop the essential flanges and reinforcement with approprite dimensions and checking draft by performance draft analysis ,calculating section inertia ,heat distortion and snow load on the roof. ROOF:      …

  SECTION MODULUS HOOD :                   * To find section modulus of the hood and optimization to improve the overall section modulus.                   * The section modulus is geometry property of the…

INTRODUCTION :                        * Fender is the US english term of an automobile (vehicle body) that frames a wheel well                         * Its primary purpose is to prevent sand,mud,rocks,liquids and other road spray from being through into the air by the rotating tire.when vehicles is moving tries pick up…

DEFINE BENCHMARKING:                   * Benchmaking in the automobile industry involves a structured comparsion between similar products services or processes on some dimensions of performnce.                   * By…

AIM:               * To write a code MATLAB to parse the NASA thermodynamics data file and calculate the thermodynamic properties of various gas species  OBJECTIVE:               * To write a function that extracts the 14 co-efficient…

AIM:        To sloves the ODE which respresents the equation of motion of a simple pendulum with damping. Objective:         To  write a program that solves the following ODE which respresents the equations of motion of a simple pendulum with damping and create an animated…