Week 8 - Challenge 2 - Switch Bezel Design

                                                                     Engine:  Aim:  To route the  wiring harness on the  given Engine and flatten the  view drawing in CATIA V5.  Objective :  The objective of a project is to route the wiring harness on the given Engine and prepare flatten view drawing in CATIA V5.  All…

                                                                                BACK DOOR:  Aim :  Route…

                                                                     Engine:  Aim:  To route the  wiring harness on the …

                  SKILL LYNC         PROJECT REPORT     MODELLING OF SUNSEEKER PREDATOR YATCH                                BY G.ROKITHKUMAR   OBJECTIVE The objective…

     AIM:              The aim of the project is to model a butterfly_valve and to apply the GD&T for different parts of the butterfly_valve  and assembly..      INRODUCTION TO BUTTERFLY VALVE :                …

 OBJECTIVE :         1) From the  given classA surface,  develop a back door  using appropreiate design methodoliges..         2) The objective of  this project is to design the back door of a car with a inner pannel, outer pannel and the reinforcement…

OBJECTIVE:         They are provided car roof styling design develop the BIW Roof rail, the bow roof rail, the center roof rail and the rear roof rail by the following engineering standards. The roof must subjected to draft analysis to verifying whether its satisfies the manufacturing requirements…

FENDER DESIGN AIM: To design a  front fender of the car by following the given master section as per design considerations of OEM by using NX Cad FENDER It is a aesthetic component/part of a car that frames the wheels. Prevention of sand,  mud particles and other road contaminants from being thrown into…

OBJECTIVE:         To study the standard and the regulation for the fender design of wheel arch area and then analysis the data which is given in the question whether the wheel arch area will going to pass the standards or not.         There is various standard which normally varies by region and there road structure like…

OBJECTIVE:              To increase the section modulus of the hood for increasing strength by using Nx cad. SECTION MODULUS:              Section modulus is a geometric property for a given cross section used in the design of beams or flexural…

Objective:     In this project i am  going to design car hood inner panel by using Nx cad and which is helps to get  familiar with the Nx cad options , features and tools and also going to learn what are the design parameters and the engineering skills required to make the hood.     Introduction:…

UNDER BODY COATING : INTR0DUCTION :                           The main purpose of undercoating is to check rust especially in the body components like frame rails along with other exposed metal parts. Underbody coating can also reduce wear and tear.…

AIM: DETAILED REPORT ON BENCHMARKING To prepare a report explaining what is Bench-marking , Compare at least 4 Vehicles and Provide a Preoper conclusion for the report ,suggesting a suitable vehicle among the comparison made. WHAT IS BENCHMARKING ? It is the process of comparing one's business process and performance…

 QUICK RETURN MECHANISM First we have to create all parts and then assemble those to get quick return mechanism. 1.SLIDER LINK 2.FIXED SUPPORT 3.SLIDING BLOCK   4.SLIDER 5.PIN ASSEMBLY   PART 1 DRAWING:   PART 2 DRAWING: PART 3 DRAWING:   PART 4 DRAWING:   PART 5 DRAWING:   ASSEMBLY DRAWING:…

Your Answers Objective: The main aim of this challenge is to create a solid body of 'Door Trim Lower' with the help of the closed surface method by using the 'Generative shape design' workbench in CATIA V5. Performing the 'Draft Analysis' on the solid part body of the Door trim. Overview:Initially, we need to offset…

Aim : To create a CAD model of a side door trim panel from given class A surface . Objective:  a) Creation of side door trim panle from given class A surface . Apply thickness to it and use attachment features .  b) Creation of flanges and heat stakes from given master sections . c) Creation of dog house and various attachment…

OBJECTIVES: To create the class B and class C surfaces from the given class A surface To form a solid geometry by combining all the surfaces To create a dog house for the solid part whilst following the design rules To perform draft analysis on the class A surface and the solid part model A-PILLAR The structure of an automobile…

AIM: To Create the Door Handle Component from the given Class-A surface. To Create the tooling axis for the given Class-A Surface meeting the requirements of the draft angle. To Attach B side Features in the component. To perform the Draft analysis on the model.  TOOLS USED: Boundary Join Multiple extract Bisecting…

AIM: To create a switch bezel from the given A surface by considering a thickness of 2.5 mm and also creating core and cavity blocks for it. PROCEDURE: A class surface: The input of the product designer is in the form of the A- class surface. The job of the product designer is  to create the B and C surfaces…

  OBJECTIVES: To create the class B and class C surfaces from the given class A surface To form a solid geometry by combining all the surfaces To create a dog house for the solid part whilst following the design rules To perform draft analysis on the class A surface and the solid part model PRE-DESIGN CHECKS: Before…

AIM : To create the Bumper Design Plastic component through the given Class-A surface.   Objective To create a tooling direction. To perform draft analysis for given A-Surface and prepare the final close body. To design the Bumper plastic component by creating the B-Surface and C-Surface using the given Class-A surface.…

Objective:             1. To design coin holder as per automotive OEM standard.             2. Create B class and C class and tooling axis.             3. Convert close  the surface into solid body and provide the thickness of 2.5mm.             4. Performing draft analysis to verify the creation of the tooling axis and…

OBJECTIVE:                 The main purpose of the challenge was to create the class-B surface, class-C surface with the given class-A surface and performing the draft analysis by creating the tooling axis of the plastic component switch bezel by taking the thickness of 2.5mm of the surface.   TOOLING AXIS CREATION PROCESS…

 REPORT   OBJECTIVE:     The main of this project is to perform the draft analysis and model the base bracket design through the given class A Surface . Beginning with the creation of the tooling axis, Class B surface. Beginning with the creation of the tooling axis, Class B surface development, and then class C surface…

                                                                       PROJECT REPORT                                             MODELLING OF AMERICAN CHOPPER  ON SOLID WORKS                                                                                                                                                                                 …