Week 8 - Challenge 1 - Base Bracket Design

BACK DOOR DESIGN 1    INTRODUCTION The back door or tailgate is in the back portion of the car, where luggage and spare parts are being stored. The cars are defined based on the car's back door as a sedan, hatchback, coupe. 2        DESIGN IN NX CAD The styling team gives the…

 ROOF CHALLENGE OBJECTIVE: For the Given Roof styling, develop the essential flanges and reinforcements. Creation of Roof ditch area with tool opening angle of 3 degree. min Provide appropriate dimensions and validate for Draft analysis. Section modulus study on 0-Y section for the Master sections created for Front…

Fender Design Using NX Cad 1. Introduction The fender is the side frontal portion of the vehicle, which protects the pedestrians from small dust particles. There are five mounting regions in the fender Bumper mounting A-pillar mounting Sill mounting Splash mounting Drip mounting The master section of the fender is given…

AIM: This project shows that examine the given fender wheel arch design to verify if the wheel arch of the fender meets the European standards. FENDER: Fender is the US English term for the part of an automobile (vehicle body) that frames a wheel well (the fender underside). Its primary purpose is to prevent sand, mud,…

SECTION MODULUS CALCULATION 1   INTRODUCTION SECTION MODULUS is the ratio of total moment resisted by the section to the stress in the extreme fiber. It gives an idea of how much load a structure can withstand if section modulus increases the moment of resistance increases, and hence its load-bearing capacity…

  Hood Design USing NXcad 1. Introduction HOOD: The hood is the cover of the engine in the vehicles with an engine at its front. The hood has two panels one is the outer panel, and the other is the inner panel. The outer panel design depends on the aerodynamics and car style. The inner panel design mainly checks…

UNDERBODY COATING UNDERBODY COATING: Underbody coating provides long term protection from corrosion to a car’s underbody. It also protects parts like internal body panels, frame rails, and other inner cavities that are not physically accessible but are prone to corrosion. Modern Automotive Coating Processes…

Mr . D.S. Pughazhyendhii's family requires what Safe Car yet the value which offers an Equilibrium strike of Mileage, Maintenance with Good space, Features and a Social Status too of not to be owning a car which is of entry segment but one which offers Value. With Transformation happening in Mindsets - Safety along with…

                                                           PROJECT-1 Aim- To route the wiring harness on given Back dore and flatten view drawing in CATIA V5. Objective-…

  1       INTRODUCTION The automotive wiring harness is referred to as the central nervous system in the vehicle. It mainly consists of an electrical harness and the mechanical harness in the design. The current project is focused on the mechanical wiring harness and its rules and procedure…

INTRODUCTION The wiring harness flattening consists of assembly of geometrical bundle to form a flatten bundle to get the 2D drawing details. For the mechanical wiring harness, assembly of geometrical bundle is the main component. In the present project, the wiring harness for the following mentioned figure ASSIGN ELECTRICAL…

DESIGN OF WIRING HARNESS ROUTING IN CATIA V5 INTRODUCTION The wiring harness routing consists of assembly of geometrical bundle and electrical bundle. For the mechanical wiring harness, assembly of geometrical bundle is the main component. For assembly of geometrical bundle, the connectors, clips, grommets must be electrically…

DESIGN OF WIRING HARNESS ROUTING IN CATIA V5 INTRODUCTION The wiring harness routing consists of an assembly of the geometrical bundle and electrical bundle. For the mechanical wiring harness, assembly of the geometrical bundle is the main component. For assembly of the geometrical bundle, the connectors, clips, grommets…

1. P - CLAMP: P-Clamp is an Electrical Support equipment which provides support to the wire bundle to remain fixed to the automobile or any components or parts. The wire bundle can enter and exit from any side as it is a bi-directional equipment. So, we need to specify the Entry and Exit points from both the sides. To…

  WIRING HARNESS DESIGN IN CATIA V5 INTRODUCTION Wiring harness is the combination of electrical and mechanical CAD to connect all the electrical parts in the automotive at the optimum level.   BASICS OF (EDS)ELECTRICAL DISTRIBUTION SYSTEM  AND WIRING HARNESS 1) Electrical Distribution System: It runs…

Objective: To make a solid body of a side door trim of a vehicle from the given class A of 4 parts of the door trim which are Door Armrest, Lower Substrate, Map Pocket,Bottle Holder,and Also, B side features like doghouse, heat stake and locator should be added, all obeying the design rules and guidelines.  …

Object:-  Design of A pillar Design with Master Section   Class A Surface:-                           The Class-A modelling process typically starts with a fully developed design, either as a scanned clay model or an Alias model. Because the…

Week 9 - Project-1  Door Trim Lower with Engineering Features OBJECTIVES: To create the class B and class C surfaces from the given class A surface To form a solid geometry by combining all the surfaces To create a dog house for the solid part whilst following the design rules To perform draft analysis on the…

Dog house design- Extract the base of Class A Surface and offset it with part thickness as 2.5 mm Draw sketch of rectangle and should be open from one side for dog house.   Using extrude & shell with tooling direction and draft it at an angle of 1.5 degree for outer surface. Give draft to the inside surface of…

DOOR HANDLE Tooling Axis creation: It is defined as the direction in which the mould/core and cavity open. Selection of the direction of the tooling axis depends on the ease at which components can be easily ejected.   By analysing the component the most easily ejectable direction is somewhere close to the Z direction,(might…

    Report : Parting Surface:Parting surface is the surface which acts as connecting between core and cavity    Parting Line: is the intersecting between parting surface and component , core and cavity to split each other    Core& cavity block: is the dipression to make a component along with the tooling axis     

    Detail Report: Aim: From The Class A surface We Need to Creat a Class B&C Surface  Tooling Axis: By creating Draft Angle Analysis , We Can Identify the safer Ejection Axis for the part Class B Sirface:In Bumper There is More patch Face is there so we Offset the A surface  In Class B surface…

  Note: In Class A i Did Get Cut holes in the basket   Report: Tooling Axis Was Creatd to the Coin Holder, Which Is Helps To Eject The Part As Core And Cavity From The Class A surface, We Extract the the Surface to Creat Class B Surface & calss C Suface And Its Makes to Closed Component  Drafting Analysis…

  Report: We Recived The Class A model Of Base Bracket , We Do Creat Tooling Axis And From the class A we need to Extract B surface, And By Giving Sweep and Drafting Class C surface was Created, And We Need To Give Close Body For the Solud Component   

Feature Tree Of Radar Mast Dimension View Iso View Front view Left side view Top View     Design, Assembly and Photo-Realistic Rendering of an American Predator Yacht   OBJECTIVE The objective of the project is to design and model all the parts of an American Predator Yacht and assembling it to create the…

Title Of The Project:                                   American Chopper    AIM & OBJECTIVE To create different parts of a American chopper in Solidworks using various types of sketches and features tools. To assemble the…