Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Read more Projects by Kuldeep Korke (32)
Project 1
WIRING HARNESS DESIGN PROJECT 1 AIM Design and develop the Wiring harness on Given V6 Engine and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. INTRODUCTION A wire harness, also commonly referred to as…
23 Nov 2023 12:39 PM IST
Wiring harness design in CATIA V5 - 3D modeling Week 7 Challenge
AIM: TO FLATTEN THE WIRING HARNESS AND DRAFT THE WIRING HARNESS ASSEMBLY. GIVEN: HARNESS ASSEMBLY: HARNESS FLATTENING: WE GO TO THE HARNESS FLATTENING WORKBENCH AND DEFINE THE FLATTENING PARAMETERS. WE USE THE EXTRACT COMMAND TO BRING THE HARNESS ASSEMBLY TO THE FLATTENING WORKBENCH HERE. CHOOSING A SUITABLE PLANE WE FLATTEN…
02 Oct 2023 07:42 PM IST
Wiring harness design in CATIA V5 - 3D modeling Week 5 & 6 Challenge
Wiring harness design in CATIA V5 - 3D modelling Week 5 & 6 Challenge Aim: Route two electrical harnesses per the given layout and interconnect them as a single harness assembly check for bundle continuity, and bundle warnings, and then provide annotations for the final harness assembly. Objective: The objective of this…
27 Sep 2023 06:52 AM IST
Wiring harness design in CATIA V5 - 3D modeling Week 4 Challenge
Aim: 1) To Route the following harness layout in the Electrical workbench. 2) Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Given: CAD data of the following Connectors: DT06-4S DT06-6S DT06-2S DT06-08SA Connectors Layout Design: Steps to be followed: 1. Download connector 3D data…
23 Sep 2023 09:16 AM IST
Wiring harness routing & packaging Rules Week 3 Challenge
Wiring harness routing & packaging Rules Week 3 Challenge Q1. Download following clip cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. Hellarmann Tyton – 21160129 process: Create two points one as entry and another as exit point. create planes at two…
19 Sep 2023 09:33 PM IST
Wiring harness design in CATIA V5 - 3D modeling Week 2 Challenge
Wiring harness design in CATIA V5 - 3D modeling Week 2 Challlenge AIM: Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip. Deutsch DT06 – 08SA ( https://www.te.com/usa-en/product-DT06-08SA.html)…
10 Sep 2023 08:56 AM IST
Week 10 - Challenge 3 - Door Trim Lower with Engineering Features
DOOR TRIM LOWER Aim: To Create the Door trim lower component through the given Class-A surface. Objectives: • Creation of Tooling axis with appropriate draft angle. • Creation of other surfaces (eg, B and C surfaces) for creating a solid component. • Perform Draft analysis on Class A surface and Solid model hence created.…
03 Sep 2023 09:48 PM IST
Advanced Sheet Metal Design Using NX Cad Challenge_7_ Metal bracket-II
NX_Bracket-II_stp_KULDIP_KORKE.stp Creating Metal Bracket From the 2D drawing Aim The Aim of this project to create the Metal Bracket from the 2D- Drawing. To use the commands Advanced Flange – used to create the flanges according to the geometry. Gusset -used to create the supports…
03 Sep 2023 06:19 PM IST
Advanced Sheet Metal Design Using NX Cad Challenge_6_Bracket
NX_Bracket_KULDIP_KORKE Title of the project:- Advanced Sheet Metal Design Using NX Cad Challenge_6_Bracket Objective: To design a Bracket using Siemens NX Sheet metal application. Introduction:- 1. SIEMENS NX:- NX formerly known as "unigraphics", is an advanced high-end CAD/CAM/CAE, which has been owned since 2007 by…
02 Sep 2023 12:12 PM IST
Advanced Sheet Metal Design Using NX Cad Challenge_5_Odd Shaped Enclosure
ODD SHAPED ENCLOSURE OBJECTIVE :- To design an odd shaped enclosure and create a draft of it using Siemens NX Sheet metal application. INTRODUCTION :- Sheet metal is metal formed by an industrial process into thin, flat pieces. Sheet metal is one of the fundamental forms…
02 Sep 2023 11:53 AM IST
Week 14 challenge
Objective The objective of this project is to model a butterfly valve and apply GD&T to the different parts and assembly of the butterfly valve. Introduction A Butterfly valve is a quarter-turn rotational motion valve, that is used to stop, regulate, and start a flow. Butterfly valves are easy and fast to open.…
28 Aug 2023 02:27 PM IST
Advanced Sheet Metal Design Using NX Cad Challenge_2_Box Assembly
TITLE: SHEET METAL BOX ASSEMBLY DESIGN USING SIEMENS NX. OBJECTIVE: Learn to design a sheet metal Box Assembly in industrial manner by using Siemens NX. INTRODUCTION: Sheet metal parts are widely used in machinery, enclosure, brackets, and automobile due to its various advantages. The parts are normally manufactured…
26 Aug 2023 11:44 PM IST
Advanced Sheet Metal Design Using NX Cad Challenge_1_Casing Design
TITLE: Advance Sheet metal Design of CASING OBJECTIVE: To design a sheet metal model of the casing using the NX CAD tool. INTRODUCTION: Sheet metal is metal formed by an industrial process into thin, flat pieces. Actually,…
21 Aug 2023 10:58 PM IST
Design of backdoor
BACK DOOR ASSEMBLY
29 Jan 2023 09:12 AM IST
Roof Design
ROOF DESIGN OBJECTIVE : The objective of this project is to design car roof with essential flanges and reinforcements like ditch area , front roof rail , bow roofs, central roof rail and rear roof rail for the the given styling surface Perform a curvature study on the roof and perform the calculations…
25 Dec 2022 06:37 PM IST
Fender Design
FENDER DESIGN OBJECTIVE : The main objective of this project is to design a fender using a new age design software - NX - CAD INTRODUCTION : Design of any product starts from an requirement . The design engineer sketches the product based on the the requirement . Then the 2D sketch with the proper dimensions…
02 Dec 2022 02:39 AM IST
Fender Design - Wheel Arch Challenge
AIM : To calculate wheel arc radius for the given model and check whether it passes the European standard oo not.ABOUT WHEEL ARC : Wheel Arch is an arch shaped cavity in the fender bod, which houses a wheel. The main intention for the calculation of…
02 Dec 2022 01:54 AM IST
Fender Design - Wheel Arch Challenge
AIM : To calculate wheel arc radius for the given model and check whether it passes the European standard oo not.ABOUT WHEEL ARC : Wheel Arch is an arch shaped cavity in the fender bod, which houses a wheel. The main intention…
21 Nov 2022 11:15 AM IST
Section Modulus calculation and optimization
Title- calculation of section modulus of hood design and also come up with improved section modulus Introduction SECTION MODULUS Section modulus is the ratio of total moment resisted by the section to the stress in the extreme fibre. Section modulus give us idea about how much of load the given structure can take. If the…
16 Nov 2022 11:30 AM IST
Underbody Coating
UNDERBODY OVERCOATING Car Undercoating: No matter the climate, the underbelly of every vehicle needs proper care and protection. Undercoating helps protect your vehicle against rust and corrosion. Seals on the underbelly parts have gotten a lot tighter and more effective at keeping out dust and moisture, but there are…
16 Nov 2022 09:56 AM IST
Benchmarking
BENCHMARKING Benchmarking is a process of measuring the performance of a company’s products, services, or processes against those of another business considered to be the best in the industry, “best in class.” The point of benchmarking is to identify internal opportunities for improvement. By studying…
16 Nov 2022 09:50 AM IST
Hood design-Week 2
REPORT on Hood Design AIM- To Design Hood outer panel, inner panel and the necessary reinforcements by following the Master section mentioned with the design parameter, (Hinge,Striker) included. Design Methodology 1. Develop the inner…
16 Nov 2022 09:43 AM IST
Week 9 - Attachment Feature Creation - Challenge 2
AIM: To create the Screw boss and Dog House for the Centre console door trim by considering the design rules. OBJECTIVE: General Guidelines for Bosses: Draft - 0.5 degrees on walls of boss Thickness - Typically 40%* of the nominal wall at the base. Height to Diameter…
02 Oct 2022 08:59 PM IST
Week 9 - Attachment Feature Creation (Ribs & Screw Boss) - Challenge 1
DOOR HANDLE Tooling Axis creation: It is defined as the direction in which the mould/core and cavity open. Selection of the direction of the tooling axis depends on the ease at which components can be easily ejected. By analysing the component the most easily ejectable direction is somewhere close to the Z…
29 Sep 2022 01:29 AM IST
Week 8 - Challenge 6 - Core & Cavity Design
Objective: The main objective of this challenge is to design a Core and Cavity for a Switch Bezel' in CATIA V5 with the help of a surface workbench. Before we design the core and cavity, we should perform a draft analysis on the solid part body of the switch bezel. Core Design: Initially, I have taken the boundary…
25 Sep 2022 07:58 PM IST
Week 8 - Challenge 4 - Bumper
Objective: The main objective of this challenge is to create a solid body of 'Bumper' with the help of the closed surface method by using the 'Generative shape design' workbench in CATIA V5. Performing the 'Draft Analysis' on the solid part body of the Bumper. Overview: Initially, we need to offset the given Bumper…
24 Sep 2022 07:57 PM IST
Week 8 - Challenge 3 - Coin Holder Design
AIM : To create a Coin Holder plastic component through the given Class A surface and perfoming the draft analysis on the model objectives : To ensure proper tree structure is followed To keep the design as per requirement All the sketches should be iso constrained To publish the Class A,B and C Surface. PROCEDURE : …
15 Sep 2022 11:21 PM IST
Week 8 - Challenge 2 - Switch Bezel Design
Aim Create the Switch Bezel Plastic component through the given Class - A surface Objective The objective of the project is to design the switch bezel and to do a draft analysis for it by creating the required tooling direction…
28 Aug 2022 08:31 PM IST
Week 8 - Challenge 1 - Base Bracket Design
28 Aug 2022 06:42 AM IST
Radar Mast & Final Assembly of Yacht
Kuldip_Korke_Radar_Must kuldip_Korke_Yacht_Assembly
26 Jun 2022 12:26 PM IST
Photo Realistic Rendering
DESIGN OF AMERICAN CHOPPER INTRODUCTION:- This Project based on the Design of American Chopper and This Report Contains Brief explanation of designing of American Chopper By using Solid works software , from initial to final sketch including solid modelling ,surface modelling tool explanation with dimension.…
15 May 2022 11:16 AM IST