Week 3- Geometry cleanup and Mid-surfacing

WEEK-3 GEOMETRY CLEANUP & MIDSURFACING                             Geometry cleanup and Mid-surfacing AIM : To extract midsurface and provide connections of the tube and to perform modal analysis of the blocks.   OBJECTIVE : To extract…

PROJECT AIM : Develop a double-acting actuator model using Simscape Multibody and Simscape components. OBJECTIVE : The mechanical system of the cylinder needs to be built using Simscape Multibody library components/blocks, and the hydraulic system needs to be modeled using Simscape library physical components. THEORY…

  Aim:To design the transfer function of mass spring damper system and add a pid controller. Objectives:                       transfer function of a mass spring damper system and use it in the model. Add a PID controller to adjust the force on mass so that its position follows a reference signal. the matlab model of the…

DEVELOPMENT OF DOOR TRIM PANEL AIM: To develop the door trim (interior) panel with the given class A input and master sections using CATIA V5. DOOR TRIM: The panel covers the inside of door trim where various electrical components of the car are connected. We design the plastic side of door trim panel which is attached…

A PILLAR DESIGN WITH MASTER SECTION AIM To create an A-pillar using the given CLASS-A surface and Master section. INTRODUCTION Back in the day, cars were mostly made of steel and over the decades lightweight alternatives have increasingly found their way into automobile designs. Current economic and ecological concerns…

DOOR TRIM LOWER WITH ENGINEERING FEATURES Aim: To Create the Door trim lower component through the given Class-A surface. Objectives: • Creation of Tooling axis with appropriate draft angle. • Creation of other surfaces (eg, B and C surfaces) for creating a solid component. • Perform Draft analysis on Class…

Project - Data Handling and Interpolation RESULT All VALUES V(Volt) I(mAmp) -17.300 -28.000 -17.200 -28.173 -17.100 -24.000 -17.000 -19.000 -16.900 -15.869 -16.800 -14.000 -16.700 -12.235 -16.600 -10.502 -16.500 -9.000 -16.400 -7.881 -16.300 -7.106 -16.200 -6.591 -16.100 -6.251 -16.000 -6.000 -15.900 -5.767 -15.800 -5.539…

Attachment Feature Creation - Challenge 2   AIM Create the Dog House for the Door Trim considering the design rules   INTRODUCTION DOG HOUSE Dog house is an engineering feature used in plastic design. Dog houses are used as support feature. Sometimes other engineering features like snaps, locators, screw bosses…

Fundamentals of Electrical Systems and Electrical Architecture Project - Analysis of a practical automotive wiring circuit 1.Identify each of the major elements in the above automotive wiring diagram.  ANS: Genarator Junction Block Battery Starter Ignition coil Ignitation switch Distributor Ammeter Foot selector switch…

 Attachment Feature Creation (Ribs & Screw Boss) AIM: To Create the Door Handle Component from the given Class-A surface. To Create the tooling axis for the given Class-A Surface meeting the requirements of the draft angle. To Attach B side Features in the component. To perform the Draft analysis on the model. …

BUMPER DESIGN Create the Bumper Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Take the Thickness of the component to be 3…

ASSEMBLY DRAWINGS  QUICK RETURN MECHANISM   ASSEMBLE  CV JOINTS PARTS ASSEMBLY         

   Aim       Create the Switch Bezel Plastic component through the given Class - A surface    Objective        The objective of the project is to design the switch bezel and to do a draft analysis for it by creating the required tooling direction with the help…

BASE BRACKET  CLASS A SURFACE (GIVEN) TOOLING AXIS Create the tooling axis Point creation (Circle curve) create plane YZ plane is created by using the circle centre ponit INTERSECT  By using these YZ plane & class A surface  to create the INTERSECT Two point line  (Create both sides) BISECTING LINE …