Week 2 Challenge

Aim: To build an Advanced Driver assistant system as per the given requirement. ADAS:   Adaptive Cruise Control Feature for passenger cars allows the host vehicle to adapt to the speed in line with the flow of traffic. Driving in heavy traffic or keeping a safe distance to the preceding vehicle calls for a high level…

Title of the project: Vehicle Direction Determination Aim of the project: Identifying the direction of the vehicle is one of the important & diverse features in Autonomous driving & Advanced Driver Assistance Features. This particular sub-feature of identifying the direction of a vehicle is basically identifying…

Create a stateflow or Simulink model for the following flowchart. Load the .mat file into the workspace. The input to the model would be the power demand. The output should be: Fuel cell power Battery power FC Operating state (running, standby) Create plot of these outputs against time. Aim:- The aim of the project is…

Question 1: Consider a scenario where an aggressive driver is accelerating very rapidly and braking harshly in a city driving. Is battery better a choice to supply power than UC in this scenario? True False False. In an aggressive driving scenario with rapid acceleration and harsh braking, the energy demands on the power…

Question 1:Compare four different types of fuel cells and state their applications. Properties Proton Exchange Membrane Alkaline Fuels cells Phosphoric Acid Fuel Cells Solid Oxide Fuels Cells Definition Proton Exchange Membrane (PEM) fuel cells are a type of fuel cell that uses a proton-conducting polymer membrane as an…

Using MATLAB/simulink and  the drive cycle from the attached excel sheet, find- The max heat generation of the battery  The SOC of the battery at 2 *104second of the battery operation Time Time Step Battery Current 00:00.4 0.1 -0.9632 00:00.5 0.2 -0.952 00:00.6 0.3 -0.9072 00:00.7 0.4 -0.9632 00:00.8 0.5 -1.0304…

1. Design a battery pack for a car roughly 150 Kw with 120 V. Use 3500 mAh 3.6V nominal NMC chemistry cell.        a. Design the battery pack configuration.         b. Draw the BMS topology for this battery pack. Here Given is, Rated voltage = 120V Nominal Voltage = 3.6V Cell…

Electric Vehicle:-  a)Electric Vehicle is a vehicle that uses electric motors to produce power and a battery to store energy. b) It uses an electric motor for propulsion and moving the vehicle instead of an internal combustion engine. System level Block diagram of EV:-     The electric vehicle consists of-…

Electric Rickshaw: Electric rickshaws are a boon to the environment and a great way to get around town. They are emissions-free, quiet and efficient. They are also very affordable, which makes them a great option for those on a budget. Electric rickshaws are a great way to reduce traffic congestion and pollution levels…

Electric Vehicle:-  a)Electric Vehicle is a vehicle that uses electric motors to produce power and a battery to store energy. b) It uses an electric motor for propulsion and moving the vehicle instead of an internal combustion engine. System level Block diagram of EV:-     The electric vehicle consists of-     a) Charging…

Part A: 1) How Much Do Airplanes Weigh? To this day it still amazes me how something that can weigh so much can even get airborne! Some of the weights that airplanes take off are staggering. In this article, I want to look at some of the most recognizable aircraft and break down what they weigh and what makes up the weight.…

1) Energy required for braking for different drive cycles can be calculated in excel sheet: 2) An electric motor can’t develop braking torque at a high speed similar to starting, because the Braking Torque of an EV Motor is not as high as the Acceleration Torque. Therefore Regenerative braking is cannot happen…

1)Speed control DC Motor using BJT H-Bridge:-  Description The Bipolar Junction Transistor (BJT) when used for power switching applications, operates as an IGBT. When it is conducting (BJT operating in the saturated region), a forward voltage Vf is developed between collector and emitter (in the range of 1 V). Therefore,…

1) Types of Converter used in an EV are: AC to DC Converter: It converts Alternating current to Direct current.Commonly used as rectifiers.Widely seen in battery charging. DC to DC Converter: It converts unregulated DC input to regulated DC output. They are 3 types i.e. Isolated,Non Isolated and resonant converters.They…

1) Mapped Model of Engine:-It is used in steady state Engine Performance.It is used when we have data from dynamometer.     Dynamic Model of engine:-It is used as engine behaviour.The Engine characteristics are decomposed into smaller components and the real time performance is derived.This is used when we need…

1)In this case: We first open the script advisor.m.Then we run the advisor command in the command window. The advanced Vehicle simulator opens.We click on start. We then select EV_defaults_in in the load file and only change the cargo mass value to 500 keeping other values to default. Now click on continue and the other…

  How to design a battery Pack: 1) To design the battery pack of 6.49KWh capacity we can take Lithium Ion cells. 2)Now we know that we have 18 cells in series and 7 in parallel i.e.18S7P. 3) So before connecting the cells we need to do the cell balancing so the capacity of each cell is same. 4)There are two types…

Here, There are 10 cells connected in series. Ther are further connected to controled current source then voltage and current sensor. A stateflow logic is used to give charging and discharging logic. The output is displayed in the scope.

Here we have got the buck converter, About the model: A step output is given for the buck converter which is connected to PWM generator DC-DC. They are futher connected to the mosfet. It is connected to voltage measurement block diode then further connected to the Inductor,capacitor and resistor. The output is seen bt…

Drive cycle:- It is known as the variation of speed with respect to time. There are two types of drive cycle: a)Modal type: invovlve straigh acceleration and constant speed condition. b)Transient type: It invovles many speed variation. The modal contains an FTP 75 Drive cycle source. An electric vehicle powertrain blockset.Environment,Driver,controllers,A…

Title: PWM controlled fan load and DC motor Description: Here the model is about pwm controlled fan load with dc motor. There are two parts here. Fan load and DC motor. Here is we see we can see: Pulse Generator: Here pulse type determines the computational technique used in PWM. Controlled Voltage Source: It is an ideal…