Week 2 Air standard Cycle

         TO PERFORM ANALYSIS ON A CYCLONE SEPARATOR AND CALCULATE THE SEPARATION EFFICIENCY AND                                                                                PRESSURE  DROP.   CYCLONE SEPARATOR: Introduction: A cyclone separator is a type of mechanical separator that uses centrifugal force to separate…

                                                                           FLOW OVER A BACKWARD FACING STEP FLOW SEPARATION: Flow…

                          SIMULATION OF FLOW INSIDE A CHANNEL USING CONVERGE    AIM: The aim of this project is to simulate the flow in a rectangular duct with dimensions of 0.1m in the X direction and 0.001m in the Y and Z directions using…

Identify each of the major elements in the above automotive wiring diagram.Explain the purpose and working of any three elements briefly. An electric circuit diagram in an automotive system is necessary for several reasons. It helps in understanding how the system works, troubleshooting issues, modifying and customizing…

                                       CONJUGATE HEAT TRANSFER ANALYSIS ON EXHAUST PORT   PROBLEM STATEMENT: Give a brief description of why and where a CHT analysis is used. Maintain the y+ value according to the turbulence model and justify the results.  Calculate the wall/surface heat transfer coefficient on the internal…

r                                     CONJUGATE HEAT TRANSFER ANALYSIS ON A GRAPHIC CARD   Conduction is the transfer of energy from the more energetic particles of a substance to the adjacent, less energetic ones as…

                                       CONJUGATE HEAT TRANSFER ANALYSIS ON EXHAUST PORT   PROBLEM STATEMENT: Give a brief description of why and where a CHT analysis is used. Maintain the y+ value according to the turbulence…

                                                                                          …

                                                           BATTERY THERMAL MANAGEMENT SYSTEM   Problem Statement:Perform the heat transfer analysis using ANSYS-Fluent…

         TO PERFORM ANALYSIS ON A CYCLONE SEPARATOR AND CALCULATE THE SEPARATION EFFICIENCY AND                                                         …

                          ANALYSIS OF INSTABILITY IN TWO FLUID SYSTEM USING RAYLEIGH TAYLOR METHOD    INTRODUCTION:   The Rayleigh-Taylor instability is a fluid dynamic instability that occurs when a fluid with a lower density is placed…

                                                     EXTERNAL FLOW ANALYSIS OVER AHMED BODY   In the study of aerodynamics on an automobile, we are using a shape called the Ahmed body…

                                                                                           …

                Observing flow patterns  and  its kinetics (Motion) of fluid is a complex phenomenon when it comes to analyse the behavioural change of various variables of the flow. Particularly when the flow is in transition stages from LAMINAR to  TRANSIENT and to TURBULENT. Behaviour of fluid flow can be best described…

AIM: To perform geometrical cleanup on the given model to avoid errors and to perform SURFACE WRAP on the given model(Drive Train of a AutoMobile) to consider every element of it under meshing inorder to make the further calculations in a simplified manner with Target length of meshing element as 7mm(By considering…

AIM: To perform INTERNAL ANALYSIS on WIND TUNNEL  with given model present in it. Has to perform Pre-Processing of CFD which is required on given model and on wind tunnel viz; Geometry Cleanup, Surface Meshing and Volumetric Meshing on given Wind tunnel.   (#WIND TUNNEL WORKING PRINCIPLE How Do Wind Tunnels…

AIM: To perform INTERNAL ANALYSIS on WIND TUNNEL  with given model present in it. Has to perform Pre-Processing of CFD which is required on given model and on wind tunnel viz; Geometry Cleanup, Surface Meshing and Volumetric Meshing on given Wind tunnel.   (#WIND TUNNEL WORKING PRINCIPLE How Do Wind Tunnels Work?Wind tunnels…

AIM: To perform INTERNAL ANALYSIS on WIND TUNNEL  with given model present in it. Has to perform Pre-Processing of CFD which is required on given model and on wind tunnel viz; Geometry Cleanup, Surface Meshing and Volumetric Meshing on given Wind tunnel.   (#WIND TUNNEL WORKING PRINCIPLE How Do Wind Tunnels…

AIM: To perform INTERNAL ANALYSIS on WIND TUNNEL  with given model present in it. Has to perform Pre-Processing of CFD which is required on given model and on wind tunnel viz; Geometry Cleanup, Surface Meshing and Volumetric Meshing on given Wind tunnel.   (#WIND TUNNEL WORKING PRINCIPLE How Do Wind Tunnels…

Aim: To perform Internal flow analysis on Turbocharger , for that pre-processing stage of CFD is to be performed on it which is geometry cleanup, surface meshing and volumetric meshing has to be done using a suitable algorithm and a cut section view has to be shown for a better understanding Meshing boundaries.…

Aim : Performing geometrical cleanup and meshing on the given model (Pressure Valve) inorder to prepare it for pre-processing stage of CFD,by using suitable Meshing algorithm with Target length of 1mm,3mm,5mm. Procedure:   To pre-process a model for CFD process, there are few steps involved in it. Firstly, Geometry…

Used Publish tool to solve this challenge, solution sent as an attachment. Please find the attachment below