Week 14 challenge

OBJECTIVE:

• The objective is to design & assemble the components of the butterfly valve using various modeling & assembly features in SIEMENS NX CAD.
• Developing drawing sheets of butterfly valve assembly using various drafting tools.
• Understanding various GD&T symbols and applying the same to the butterfly valve assembly.

INTRODUCTION:

A butterfly valve belongs to a family of QUARTER-TURN valves. A butterfly valve is a flow control device that incorporates a rotational disk to control the flowing media in a process. The disk is always in the passageway, but being relatively thin, it offers little resistance to flow.

In operation, the valve is fully opened or closed when the disc is rotated a quarter turn. When the valve is closed, the disc is turned so that it completely blocks the passageway. And, when the valve is open the disc is rotated a quarter turn/90 deg so that it allows the unrestricted flow of the fluid. The valve may also be opened incrementally to throttle flow. Many different types of valves are used in flow control. They are used for a variety of reasons, such as phase (liquid or gases), pressure, piping restrictions, and solids content. Other valves are chosen for their capability to open and close in a quarter turn.

Early use of butterfly valves focused on water applications, but new designs and component materials have allowed them to be utilized in growing industrial fluid applications. Presently, butterfly valves can be found in almost every chemical plant handling a variety of diverse fluids.

Once the components and assembly are developed, GD&t(geometric dimensioning and tolerancing) is applied to each component as well as the assembly. The purpose of GD&T is to describe the engineering intent of parts and assemblies. GD&T can more accurately define the dimensional requirements for a part, allowing over 50% more tolerance zone than coordinate (or linear) dimensioning in some cases. Proper application of GD&T will ensure that the part defined on the drawing has the desired form, fit (within limits), and function with the largest possible tolerances. GD&T can add quality and reduce cost at the same time through producibility.

There are several standards available worldwide that describe the symbols and define the rules used in GD&T. One such standard is the American Society of Mechanical Engineers (ASME) Y14.5. This article is based on that standard, but other standards, such as those from the International Organization for Standardization (ISO), may vary slightly. The Y14.5 standard has the advantage of providing a fairly complete set of standards for GD&T in one document. The ISO standards, in comparison, typically only address a single topic at a time.

COMPONENTS OF BUTTERFLY VALVE:

Various components of the butterfly valve have been designed, and GD&T is applied to the drawing sheets. The following details are given below:

1. BODY OF BUTTERFLY VALVE

• Butterfly valves generally have bodies that fit between two pipe flanges. This butterfly valve has a lug body design consisting of protruding lugs that provide bolt holes matching those in the pipe flange.
• Create two circles of required diameter and use Extrude command to form a cylindrical body/housing.
• On that cylindrical body create three lugs with holes in them. This will help us connect the butterfly valve to the pipe flanges. We have created the lugs on the mid-plane and then Extruded them with reference to the mid-plane(i.e. symmetrical value).
• Using the Move object command we created similar lugs on the outer surfaces of the body with the help of lugs created earlier.

• 2. SHAFT/STEM OF BUTTERFLY VALVE

  • The stem of the butterfly valve may be a one-piece shaft or a two-piece (split-stem) design. This design consists of a one-piece shaft. The disc/plate, lever, and nut are assembled to this shaft.
  • First, create a sketch that is cylindrical in shape along with steps. That sketch must be fully constrained and closed in order to use Revolve command.

  • 3. RETAINER OF BUTTERFLY VALVE

    • It is nothing but a kind of washer assembled on the body of the butterfly valve.
    • Create a circular sketch with an appropriate diameter. Also, create 3 holes in the sketch that will help us to fix the retainer to the body of the butterfly valve.

    • 4. DISC PLATE OF BUTTERFLY VALVE

      • A disc is nothing but a flow controlling/closure member of the butterfly valve which is attached to the stem/shaft. The disk is the equivalent of a plug in a plug valve, a gate in a gate valve, or a ball in a ball valve.
      • Rotating the disk one-quarter turn or 90 Degrees opens and closes the butterfly valve.
      • Create an elliptical sketch with appropriate sizes (major & minor distance). Then put two holes along the minor axis which will be used to fix the disc to the shaft.
      • Extrude the fully constrained sketch by providing suitable thickness.

      5. LEVER HANDLE OF BUTTERFLY VALVE

      • The lever is attached at the end of the shaft/stem above the body & retainer. This lever handle is used in a small-sized butterfly valve. Using this we can regulate the flow by opening and closing the disc whenever required.
      • Create two circular sketches with the appropriate diameters, and specify a suitable distance between them. Also, create a keyway slot in the bigger diameter sketch. Join these two sketches with a line tangent to both the circles.
      • After creating the fully constrained sketch, first, extrude the circular regions and then extrude the mid-section with different thickness values.
      • Then combine all the features using Unite command. Then create a drawing sheet of the model and apply GD&T to the drawing.

      • 6. NUT - BUTTERFLY VALVE

        • It is used to keep the lever and retainer intact with each other as well as the body of the butterfly valve.
        • Create a polygon sketch (6sides) with suitable dimensions. Also, add a circular hole in the sketch so that it can be inserted into the shaft.
        • For safety handling provide a fillet on the top edge of the nut.

        • BUTTERFLY VALVE ASSEMBLY:

          • After designing every component. we have created the final assembly model using SIEMENS NX CAD.
        • please note: all images are attached below upload section