Week 10 - Challenge 3 - Door Trim Lower with Engineering Features

Report On Car Back Door Design   Aim-  To design the Back door of the car using the appropriate design methodologies, providing the necessary Reinforcements and embosses in the inner panel for strength. Design Considerations for a Back Door- Rear Visibility for Functionality and Safety. Boot Space and Accessibility. Type…

                                                                                                     Report On Roof Design Aim- To develop the essential flanges and reinforcements with appropriate dimensions and checking draft by performing Draft analysis, Calculating Section inertia, Heat distortion and Snow load on the…

Fender Design Challenge REPORT - FENDER DESIGN   OBJECTIVE - Design a Fender Model with the necessary mounting with a given class A surafce.   MOUNTS - 1. A-Pillar 2. Bumper 3. Sill 4. Cowl 5. Drip     FENDER - Fender is the American English term for the part of an automobile, motorcycle or other vehicle body…   REPORT -…

Section Modulus calculation and optimization SECTION MODULUS OF THE HOOD Objective: To find the section modulus of the hood and optimisation to improve the overall section modulus. Section Modulus: The section modulus (S) is geometric property of the cross section used for designing beams and flexural members. It does…

Design of Hood AIM To create and assemble the hood inner panel and outer panel and their reinforcements by following the design rules and master section. SOFTWARE USEDSIEMENS NX CAD 12 OBJECTIVES Design Hood outer panel, inner panel and the necessary reinforcements by following the Master section mentioned with the design…

Underbody Coating AIM: Study the underbody coating used in automobile industries. Objectives: Study about underbody coating Study about types of underbody coating and its advantages and disadvantages. Procedure: Underbody coating is usually a dense cladding (often based on rubber) applied uniformly to the undercarriage…

BENCHMARKING Benchmarking is a process of measuring the performance of a company’s products, services, or processes against those of another business considered to be the best in the industry, “best in class.” The point of benchmarking is to identify internal opportunities for improvement. By studying…

  Project 2 AUTOMOTIVE WIRING HARNESS BACKDOOR Statement of assignment: Route the Wiring harness on Given car body and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required.…

Project 1    AIM  Route the Wiring harness on Given Engine and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. ENGINE WIRING HARNESS ROUTING. Arun Kumar Updated…

Wiring harness design in CATIA V5 - 3D modeling Week 7 Challenge AIM: TO FLATTEN THE WIRING HARNESS AND DRAFT THE WIRING HARNESS ASSEMBLY. GIVEN: HARNESS ASSEMBLY: HARNESS FLATTENING: WE GO TO THE HARNESS FLATTENING WORKBENCH AND DEFINE THE FLATTENING PARAMETERS. WE USE THE EXTRACT COMMAND TO BRING THE HARNESS ASSEMBLY…

WIRING HARNESS DESIGN IN CATIA V5 - 3D MODELING WEEK 5 & 6 CHALLENGE AIM-  Route two electrical harnesses as per the given layout and interconnect them as a single harness assembly and then check for bundle continuity, bundle warnings, and then give annotations to the final harness assembly. OBJECTIVE-  …

Wiring harness design in CATIA V5 - 3D modeling Week 4 Challenge Aim:  1) To Route the following harness layout in the Electrical workbench. 2) Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Given: CAD data of the following Connectors:  DT06-4S DT06-6S DT06-2S DT06-08SA Connectors Layout…

Wiring harness routing & packaging Rules Week 3 Challenge  Wiring harness routing & packaging Rules Week 3 Challenge Q1. Download following clip cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. Hellarmann Tyton – 21160129 process: Create two points…

Wiring harness design in CATIA V5 - 3D modeling Week 2 Challenge WIRING HARNESS DESIGN IN CATIA V5 – 3D MODELLING AIM:        To Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench.…

AIM – To create a Solid body of side door plastic trim with engineering features using the Class-A Surface and master section. INTRODUCTION – The door trim panel is the interior plastic component attached to the sheet metal part of the Door. It contains engineering features like a doghouse, heat stakes…

AIM: Create the part models and assembly for the given drawings below with a report. DRAWING 1 (QUICK RETURN MECHANISM): REPORT ANALYSIS:Intially created the part of the drawing in the part workbench. Sketches and CAD Part:   After creating all the parts go to the Assembly Workbench and insert every part to the…