Section Modulus calculation and optimization

AIM:Use the provided styling surface to come up with a back door design, use appropriate design methodologies, and provide the necessary reinforcements and embosses. SOLUTION: Now we will discuss about geometric dimensioning : The most common way of showcasing the dimensions of the part are the plus minus signs .It consists…

ROOF DESIGN IN AUTOMOBILE  OBJECTIVE : The objective of this project is to design car roof with  essential flanges and reinforcements  like ditch area , front roof rail , bow roofs, central roof rail and rear roof rail for the the given styling surface Perform a curvature study on the roof and perform the…

    FEMDER DESIGN WHEEL ARCH CALCULATION: AIM: To calculate the wheel arc then it  is european stansred wether the car will pass the stansred or not.   INTURODUCTION:  Wheel Arch is an arch shaped cavity in the fender bod, which houses a wheel. The main intention for the calculation…

DESIGN OF FRONT FENDER- OBJECTIVE- To develop the front fender using Nx cad following the design parameters . INTRODUCTION: Fender is a front outer side member of a car which covers the wheel side. Fender purpose is to prevent sand, mud, rocks, liquids and other particles. Fender is a closure component, closing the…

DESIGN OF FRONT FENDER- OBJECTIVE- To develop the front fender using Nx cad following the design parameters . INTRODUCTION: Fender is a front outer side member of a car which covers the wheel side. Fender purpose is to prevent sand, mud, rocks, liquids and other particles. Fender is a closure component, closing the engine…

  AIM: To calculate the section modulus of the hood for analyzing its strength and then optimizing the hood panel for comparing the section modulus. SECTION MODULUS: Section modulus is a geometric property for a given cross-section used in the design of beams or flexural members, it is also referred to as the…

AIM: Our aim for this project is to create a hood assembly from the hood outer panel which is provided as input surface to us according to the master section sketch.Hood or bonnet is the hinged cover over the engine of the motor vehicles that is used to access the engine compartment. Hood assembly consist of different…

UNDERBODY COATING: Underbody coating provides long-term protection from corrosion to a car's underbody. It also protects parts like internal body panels, frame rails, and other inner cavities that are not physically accessible but are prone to corrosion. UNDERECOATING AND TYPES: types of underecoating: Now let us look…

1A.Aim:  Benchmark with presently available cars in the market for the following case.Mr.D.S.Pughazhyendhii is a married man who lives in Bangalore which is a highly crowded city. His Family comprises five members including his wife, a five-year-old boy, his father, and his mother. He visits his native place…

Aim: To route the wiring harness on the given tailgate assembly and prepare the flatten view drawing in CATIA V5.  A cable harness, also known as a wire harness, wiring harness, cable assembly, wiring assembly, or wiring loom, is an assembly of electrical cables or wires which transmit signals or electrical power. The…

                                                                                           …

 we have already saved the electrically defined connectors in our catalogue, we can directly import all the connectors in an assembly and place them as per the above layout and start creating the bundles accordingly this parameters file is saved along with our harness assembly. It is mandatory to save the parameter…

In this wiring harnes challenge we need to route the given harness layout in the Electrical Workbench We will create the harness layouts in  different product files. After routing these layouts we can connect both of them in a single product file and perform the below operations. Checking the bundle Continuity Adding…

 in this routing system we download the cat fail and upload and create needed geomentrys and these connectors are converted  catalogue we can assemble them using the Mechanical Assembly workbench. Now, this assembly needs to be converted into the electrical assembly using an Electrical Harness Assembly workbench.…

 1A.   In this challenge we are first going to define a mechanical cad component electrically by setting up the geometrical parameters and then using the Electrical Part Design workbench we will define the electrical support. The first given model in this challenge is a P Clamp which we need to define as…

in this wiring harness first we download the igs file from te.com and next uploaded intlo part body and next step is to define connecter as electric properties we need to create some gemetrical features to Create point and axis open the connector in the Catia part workbench click on the point command and select…

  aim: to create door trim panel using given surfaces and master sections the Project explain in brief regarding the Design life cycle followed in automotive industry by working on Practical Model car interior door trim which is a Car interior trim Part.In this Report we have explain about the steps followed to create…

  in this assembly work bench first ew do all assemble bodys in 2d drawing into 3d commands and and  assemble into single componment

 thia is a pillar master secton design : first we create tooling axis and b surface and c surface and join a and b and c surfaces then it is become a closed body and to create a extra adding features and give drafting for the body all are draw as per design rules and with sketches in this below step by step slides to the…

this is a finial out put of door trim with locators and heat stakes frist we design a door trim with heat stkes and locators to create atooling axis for givin surface and nest process is to create class b surface and and next class c surface comletion of those surfaces next step is to closed body  then the used to…

Create the Dog House for the Door Trim considering the design rules  "C" is where the doghouse contacts the backside of the surface  Doghouse wall thickness at the intersection of the part wall ( C ) should be 40% or less than the main wall stock ( T ).  The height of  ( B ) should be between 3.0 –…

to create a ribs and srew boss: in  this surface to create rib and srew boss to first create a tllo axis and with axis system ans point aton surface  the difference betweem the rib and boss is  bosses are one of the most common features seen in plastic parts However similar to ribs if bosses get too thick…

the main parts in core and cavity desin mold: Core –This duplicates the inner surface of the model. It is larger than thefinished part to allow for material shrinkage during cooling Cavity –This duplicates the outer surface of the model. Mounting bosses –Holds and position core…

to create a bumper to create tooling axis based on class a surface : after next to created a b surface with thickeness as per givem in mm: after create a c surface with proper angle and length: after comine c&a surfaceses: closed surface body: draft analysis and dircections:      

  to create tooling axis  A and B and C surfaces and clossed surface and solid part this surface processes mainly created a parts there are: tooling axis class B surface class c surface  closed suface and  draft analysis and publications 1.tooling axis: in this axis based on class A suface to taken…