Project on Concrete Mix Design for various grades of Concrete
Project Part 1
Aim : Concrete mix design calculations for M35 Grade concrete with use of fly ash.
Introduction: In the design calculation We find out proportions of concrete ingredients in term of volume and weight for 1 cubic meter of concrete. Ingredients to be calculated are Cement, Fine Aggregates (Sand), Coarse aggregates, Water, Fly Ash and Admixtures.
The main purpose of the Calculation is to determine the concrete ingredients proportion to acheive the desired concrete characteristic compressive strength as mentioned for M35 is 35 N/mm2. Also Design is done to minimize the cost of production of concrete.
Pre-test Procedures that are to be done for calculation:
- Cement Specific Gravity
- Fly Ash Specific Gravity
- Chemical Admixture Specific Gravity
- Specific Gravity of coarse aggregates
- Specific Gravity of Fine aggregates
- Water Absorbtion of Coarse aggregate
- Water Absorbtion of fine aggregates
- Free Surface moisture in Coarse and fine aggregates
- Seive analysis for Coarse and fine aggregates
- Some trial experiments for Optimum water cement ratio and characteristics compressive strength.
- Various aggregate test to be perform
Precedure:
A. Stipulations for proportioning:
- M35 grade of concrete.
- Type of cement used: OPC 43 confirming to IS 8112
- Fly ash: confirming to IS 3812 (part 1)
- Maximum nominial size of aggregate: 20 mm
- Exposure condition: Severe
- Minimum cement content: 320 kg/m3 for severe condition. (From Table 5 of IS 456 2000).
- Maximum water cement ratio = 0.45 for severe condition.
- Method of concrete placement: Pumping
- Workability: 100 mm in term of slump test (Considered for pumpable concrete)
- Degree of supervision : Good
- Type of aggregates: Crushed angular type
- Maximum cement content : 450 kg/m3
- Chemical Admixture: Superplasticizer
B. Test data for Material: -
- Cement Used: OPC 43 Confirming to IS code 8112
- Cpecific Gravity: 3.15
- Fly Ash Used: Confirming to IS 3812 part 1
- Fly ash Specific Gravity: 2.2
- Chemical Admixture: Super plasticizer confirming to IS 9103
- Chemical Admixture Specific Gravity: 1.145
- Specific Gravity of coarse aggregates: 2.74
- Specific Gravity of fine aggregates: 2.74
- Water Absorbtion of Coarse aggregate: 0.5%
- Water Absorbtion of fine aggregates: 0
- Free Surface moisture in Coarse aggregates: Nil
- Free Surface moisture in fineaggregates: 1.5%
- Seive analysis for Coarse aggregates: 20 mm fine aggregate Zone II as per IS 383
- Seive analysis for fine aggregate: Fine zone
C. Target Mean Strength: -
F'ck=Fck + 1.65*S
=35 + 1.65*5 (Standard deviation from Table 8 of IS 10262 1982
F'ck= 43.25 N/mm2.
D. Water Cement Ratio: -
From IS 456 2000, Maximum W/C ratio = 0.45
And From IS 10262 1982 graph 1 W/C rato = 0.35
Also from IS 10262 1982 graph 2 W/C ratio = 0.34
We choose W/C ratio = 0.42 based on lab experiments
E. Selection of Water Content: -
From Table 2 of IS 10262 2009, Water content is 186 liters per 1 m3 of concrete. (for slump value 25-50 mm).
for evry 25 mm increase in slump the water content increased by 3%.
Thus, Water content for 100 mm slump = 186+186*6/100
Water content = 197 liters.
For Plasticizers water content reduced by 29%.
Thus Final Water content = 197*0.71
Water content= 140 liters.
F. Cement content: -
Cement content = Water content/Water cement ratio
= 140/0.42
Cement content =334 kg/m3 of concrete (320<334<450 kg/m3 of concrete, Hence OK)
Proportioning of Fly ash: Fly ash content percentage shall be taken as 30% of the 10% increased cementetious material.
Fly Ash = 0.3 * 334*1.1
Fly Ash content= 110 kg/m3
Cement = 366-110
Cement content= 256 kg/m3 of concrete
Total Saving in the cement content = 334-256 = 78 kg/m3 of concrete.
Cementetious material= 256+110 = 366 kg/m3
G. Volume of fine aggregates: -
For Water cement ratio 0.5 the ratio of coarse aggregate to Total aggregate is 0.6
But We have water cement ratio =0.42, Thus correction procedure is inncreamenty of 0.01 to every 0.05 decrease in water cement ratio. Thus, for 0.08 decrease in water cement ratio, increament is 0.016
Ratio of coarse aggregat to total aggregate = 0.616
For pumpable concrete coarse aggregate reduced by 10%.
Thus ratio of coarse aggregate to total aggregate = 0.616*0.9 = 0.5544
Volume ratio of fine aggregate to total = 1-0.5544 = 0.4456
H. Mix Calculation: -
- Volume of concrete= 1 m3
- Volume of cement= Mass of cement/ (Specific gravity of cement *1000) = 256 /(3.15*1000) = 0.08126 m3
- Volume of fly Ash = Mass of Fly Ash/ (Specific gravity of fly ash *1000) = 110/(2.2*1000) = 0.05 m3
- Volume of chemical admixture= Mass of Admixture/ (Specific gravity of Admixture *1000) = 7.32/(1.145 * 1000) = 0.0064 m3 (2% of the cementetios material)
- Volume of Water= 140 kg or 0.14 m3
- Volume of Total Aggregates= a-(b+c+d+e) = 1-(0.08126+0.05+0.0064+0.14) = 0.723 m3
- Mass of Coarse aggregates= f*0.5544 *2.74*1000 = 0.4 *2.74*1000 = 1098 kg/m3
- Mass of fine aggregates= f*0.4456*2.74*1000= 882 kg/m3
I. Mix Proportions: -
Cement= 256 kg/m3
Fly ash= 110 kg/m3
Water Content = 140 liters.
Plasticizer = 7.32 kg/m3
Coarse aggregate = 1098 kg/m3
Fine aggregate = 882 kg/m3
J. Slump Shall be Measured, Water Content and Dosage of Admixture shall be adjusted for required slump. Design mix proportion shall be reworked for durability requirement.
K. Two more Trial for the W/C ratio variation 10% up and down shall be done and ccompressive strength gained in 7 and 28 days shall be measured. The graph between water cement ratio and compressive strength gained shall be drawn for the 3 trails of concrete mix. Recommendation for the design shall be shown accordingly.
Result:
Ratio by weight = 1 : 3.445 : 4.289 (Cement : Fine aggregate : Coarse aggregate)
Ratio by Volume = 1 : 3.96 : 4.932 (Cement : Fine aggregate : Coarse aggregate)
For quantity of material table below is reccomended
| Sr. No. | Material | Quantity Per bag of cement (kg) | Quantity Per cubic meter of concrete (kg) |
| 1 | Cement | 50 kg or 1 bag | 256 or 5.12 bags |
| 2 | Fly Ash | 21.5 | 110 |
| 3 | Plasticizer | 1.43 | 7.32 |
| 4 | Water | 27.3 kg or liters | 140 |
| 5 | Fine Aggregate | 172.3 | 882 |
| 6 | Coarse Aggregate | 214.5 | 1098 |
Project Part 2
Aim : Concrete mix design calculations for M50 Grade concrete without use of fly ash.
Introduction: In the design calculation We find out proportions of concrete ingredients in term of volume and weight for 1 cubic meter of concrete. Ingredients to be calculated are Cement, Fine Aggregates (Sand), Coarse aggregates, Water and Admixtures.
The main purpose of the Calculation is to determine the concrete ingredients proportion to acheive the desired concrete characteristic compressive strength as mentioned for M50 is 50 N/mm2. Also Design is done to minimize the cost of production of concrete.
Pre-test Procedures that are to be done for calculation:
- Cement Specific Gravity
- Chemical Admixture Specific Gravity
- Specific Gravity of coarse aggregates
- Specific Gravity of Fine aggregates
- Water Absorbtion of Coarse aggregate
- Water Absorbtion of fine aggregates
- Free Surface moisture in Coarse and fine aggregates
- Seive analysis for Coarse and fine aggregates
- Some trial experiments for Optimum water cement ratio and characteristics compressive strength.
- Various aggregate test to be perform
Precedure:
A. Stipulations for proportioning:
- M50 grade of concrete.
- Type of cement used: OPC 43 confirming to IS 8112
- Maximum nominial size of aggregate: 20 mm
- Exposure condition: Severe
- Minimum cement content: 320 kg/m3 for severe condition. (From Table 5 of IS 456 2000).
- Maximum water cement ratio = 0.45 for severe condition.
- Method of concrete placement: Pumping
- Workability: 75 mm in term of slump test (Considered for pumpable concrete)
- Degree of supervision : Good
- Type of aggregates: Crushed angular type
- Maximum cement content : 450 kg/m3
- Chemical Admixture: Superplasticizer
B. Test data for Material: -
- Cement Used: OPC 43 Confirming to IS code 8112
- Cpecific Gravity: 3.15
- Chemical Admixture: Super plasticizer confirming to IS 9103
- Chemical Admixture Specific Gravity: 1.145
- Specific Gravity of coarse aggregates: 2.74
- Specific Gravity of fine aggregates: 2.74
- Water Absorbtion of Coarse aggregate: 0.5%
- Water Absorbtion of fine aggregates: 0
- Free Surface moisture in Coarse aggregates: Nil
- Free Surface moisture in fineaggregates: 1.5%
- Seive analysis for Coarse aggregates: 20 mm fine aggregate Zone II as per IS 383
- Seive analysis for fine aggregate: Fine zone
C. Target Mean Strength: -
F'ck=Fck + 1.65*S
=50 + 1.65*5 (Standard deviation from Table 8 of IS 10262 1982
F'ck= 58.25 N/mm2.
D. Water Cement Ratio: -
From IS 456 2000, Maximum W/C ratio = 0.45 for Severe condition
And From IS 10262 1982 graph 1 W/C rato = 0.30
Also from IS 10262 1982 graph 2 W/C ratio = 0.33
We choose W/C ratio = 0.34 Based on experiments.
E. Selection of Water Content: -
From Table 2 of IS 10262 2009, Water content is 186 liters per 1 m3 of concrete. (for slump value 25-50 mm).
for evry 25 mm increase in slump the water content increased by 3%.
Thus, Water content for 100 mm slump = 186+186*3/100
Water content = 192 liters.
For Plasticizers water content reduced by 29%.
Thus Final Water content = 197*0.71
Water content= 136 liters.
F. Cement content: -
Cement content = Water content/Water cement ratio
= 136/0.34
Cement content =400 kg/m3 of concrete (320<400<450 kg/m3 of concrete, Hence OK)
Cement content= 400 kg/m3 of concrete
G. Volume of fine aggregates: -
For Water cement ratio 0.5 the ratio of coarse aggregate to Total aggregate is 0.6
But We have water cement ratio =0.34, Thus correction procedure is inncreamenty of 0.01 to every 0.05 decrease in water cement ratio. Thus, for 0.16 decrease in water cement ratio, increament is 0.032
Ratio of coarse aggregat to total aggregate = 0.632
For pumpable concrete coarse aggregate reduced by 10%.
Thus ratio of coarse aggregate to total aggregate = 0.632*0.9 = 0.5688
Volume ratio of fine aggregate to total = 1-0.5544 = 0.4312
H. Mix Calculation: -
- Volume of concrete= 1 m3
- Volume of cement= Mass of cement/ (Specific gravity of cement *1000) = 400 /(3.15*1000) = 0.127 m3
- Volume of chemical admixture= Mass of Admixture/ (Specific gravity of Admixture *1000) = 8/(1.145 * 1000) = 0.007 m3 (2% of the cementetios material)
- Volume of Water= 136 kg or 0.136 m3
- Volume of Total Aggregates= a-(b+c+d) = 1-(0.127+0.007+0.136) = 0.73 m3
- Mass of Coarse aggregates= e*0.5588 *2.74*1000 = 0.4 *2.74*1000 = 1118 kg/m3
- Mass of fine aggregates= e*0.4312*2.74*1000= 862 kg/m3
I. Mix Proportions: -
Cement= 400 kg/m3
Water Content = 136 liters.
Plasticizer = 8 kg/m3
Coarse aggregate = 1118 kg/m3
Fine aggregate = 862 kg/m3
J. Slump Shall be Measured, Water Content and Dosage of Admixture shall be adjusted for required slump. Design mix proportion shall be reworked for durability requirement.
K. Two more Trial for the W/C ratio variation 10% up and down shall be done and ccompressive strength gained in 7 and 28 days shall be measured. The graph between water cement ratio and compressive strength gained shall be drawn for the 3 trails of concrete mix. Recommendation for the design shall be shown accordingly.
Result:
Ratio by weight = 1 : 2.155 : 2.795 (Cement : Fine aggregate : Coarse aggregate)
Ratio by Volume = 1 : 2.478 : 3.212 (Cement : Fine aggregate : Coarse aggregate)
For quantity of material table below is reccomended
| Sr. No. | Material | Quantity Per bag of cement (kg) | Quantity Per cubic meter of concrete (kg) |
| 1 | Cement | 50 kg or 1 bag | 400 or 8 bags |
| 2 | Plasticizer | 1 | 8 |
| 3 | Water | 17 kg or liters | 136 |
| 4 | Fine Aggregate | 107.75 | 862 |
| 5 | Coarse Aggregate | 139.75 | 1118 |