Drafting Workbench Week 6 - Challenge 2

Development of a Door Trim panel   Intent:  To create thickned plastic components using class A surface of following door trim panel.   Objective: To create thickned component with nominal thickness using class A. To create B surface features using master section reference   door trim panel: An automobile…

      https://drive.google.com/drive/folders/1CK5GdhamJGnOi_XYcAQMSoTUj9sRod1H?usp=sharing  

    https://drive.google.com/drive/folders/11MJNUWLRY5bXiTDLtI-SbbNMGTd6GIY-?usp=sharing                  

    https://drive.google.com/drive/folders/1cH41pyWqD6vtLcK5NJ7bmJc8Hl_Mge_n?usp=sharing            

  https://drive.google.com/drive/folders/1A2y55y1ZF3D_d_Ufel-y87yzymM9l6ax?usp=sharing   Aim: Create the rib for the Centre console coin holder considering the design rules.  Tooling Axis: Tooling direction is main consideration for plastic part and mold parts because it defines movement of mold part…

  https://drive.google.com/drive/folders/1yEm6kPApwFwi8w_-KKM60DnDkFZyaXe_?usp=sharing     Draft Analysis of Switch Bezel Draft Analysis of Plastic component:   core & cavity blocks:                 

  https://drive.google.com/drive/folders/1yyoI9FruXl6U3VZvQ-D6XVq5EZy_iuuK?usp=sharing  

  https://drive.google.com/drive/folders/1qq2BDXZrxYNF1dCxPxU0OwOzds3H3cjT?usp=sharing   COIN HOLDER        Tooling axis: it is basically the direction that the mould pulls apart. the mould is build in two separate halves, basically core side and cavity side. by designing the tooling…

  https://drive.google.com/drive/folders/1jKGDwZcaoTwuvNEWXjlUmowmenxJ5jGJ?usp=sharing  

  https://drive.google.com/drive/folders/1jg0himg9bUX93LJfS_kyCopSxGjPt7ug?usp=sharing    

  https://drive.google.com/drive/folders/1yu7Yx3_5lICJdQVeqYg7ql_BaQeZzF5i?usp=sharing    

https://drive.google.com/drive/folders/13vNhkIoiZK14q2R2lLc_CebTeJ4gFmhO?usp=sharing Aim: To design the Biw fixtures compoments for following car panel. every part panel constrained with 2 pins and clamps units & rest units to constrain the total panel create the rough locators to panel with entry point of locator…

https://drive.google.com/drive/folders/1E5QQhyu5Qoti-gXO8q0tNFNMu94UUkGO?usp=sharing please find above link for model & GD & T Drafting. A butterfly valve is a valve that isolates or regulates the flow of a fluid. The closing mechanism is a disc that rotates. A butterfly valve is from a family…

  1. What is the Base Unit? What are the typical parts of the Base Unit? Base Unit: - A unit used to mount all unit over it like a clamp, pin likewise. it will rest subpart of the main unit like the pneumatic valve box which is usedto supply air to the inlet of all pneumatic cylinders. Trunking cable path is alsosupported…

https://drive.google.com/open?id=1Wr-EbH2PBd8n7VrckjZD7cC598sF87Oz   Box Assembly Box assembly sheet metal design is done by using NX 12, I used some new features in NX sheet metal features like flange, hem, normal cutout, bead, dimple & few other to create this challenge. below is the sequence & features…

https://drive.google.com/open?id=1-3SPcebXvOshFMNfCnIfoTN2Xl9VavmI Odd Shaped enclosure Creating Odd shapes for sheet metal from a solid body by using NX feature Sheet metal from solid. the different features I used in this sheet metal design are extrude, convert to sheet metal, flange, jog, bead, hole, unbend, rebend,…

https://drive.google.com/open?id=1Argm4YpeDwj0zDiFMWN7xDhQqxvbfQ-3   Bracket Creating a bracket sheet metal design by using 2d drawing. the different features i used in the sketch are counter flange, normal cutout, break corner, bead, unbend, rebend, hole. below the procedure,  the sketch in the XZ plane. created…

https://drive.google.com/open?id=1qkyf_4SinVEffc6PWPpUa4ERMleQ2Tc4 CASING DESIGN Casing Design by using advanced sheet metal features in NX CAD. In this, I used Different sheet metal features like Tab, Normal cutout, bend, Flange, Break corner, Unbend, Hole, Dimple, Bead and some other. below is the sequence I used to…

https://drive.google.com/open?id=1okMOkDbycMTX4Yo5oEQiR8yO_OrJvPHq Please find above a link to reach the yacht model.   Objective:         The objective of this project is to design components of the yacht using surface features and assemble the components by giving suitable mate relations to constrain…

https://drive.google.com/open?id=1L5prV0jPCB6XKS20PIv1dzmn5ENUIRcM   Metal Bracket-II Creating a metal bracket by using 2D Drawing. in this sheet metal design, I used different features like a normal cutout, break corner, advanced flange, bend, rebend, hole, gusset. below is the sequence of steps   Create…

https://drive.google.com/open?id=1m1jSFU3PFQNsNLTMwIfJZEm--fgblmvV please find American chopper model in the above link                             Objective: the objective of this project to design the American chopper components and assemble its components…