Creation of Column Schedule and Drawing Template using AutoCad

ANS 1:- Column Schedule

• Create drawing sheet first in unit select decimal.
• And in dimesion command also select decimal and all parameters as per standards.
• Now we will go for the converting black sheet into white by clicking on autocad symbol then click on option select display from the panel after that go for colors and select white and apply.
• Now we are going to start with Column Schedule heading.
• First click on annotation then click on standards after that manage text style click on font name and select roman.shx and set current.
• Select multiline text and height 8" start writing column schedule in capital letters.
• Draw a line of horizontal of length of 40" and 10" vertical line then use offset command give an offset of using horzontal line at distance 10'ft and by using vertical line at distance of 41'ft.
• As we know the rectangle is formed.
• Now again use offset command and give an offset of 1.5" inch by using reference of horizontal top line.
• After that by using LHS vertical line give an offset of 5'ft and by using new offseted line give and offset of 7'5" this same procedure follow 3 time again after we have 6 blocks.
• In first block draw a middle partion line at distance of 2'5"ft. Then use offset command by using bottom line give an offset at distance of 1'9"ft.
• Trim the new offseted line from first block of its middle.
• Now select multiline text give the first column heading by using same style as Col. Nos.
• After that in column half portion write TERRACE TO MUMTY and rotate it at 90 degree .
• Then in first column 2nd half portion write SIZE, MIX, MAIN REINF. and STRPS.
• By completing the 1st column we'll go for 2nd column.
• In this column we'll start with name of the column as C1 with text height of 6" inch.
• Again draw middle line in second column and trim the line where it is not required.
• After that the first half portion divide into three parts and write first 9" X 24" , M25, 4-20mm dia, 6- 12mm dia(a).
• And last portion which is blanked then wirte there as 8 dia 3" & 8" CRS (1SET OF 3 STRS).
• Now in second we have to draw a column and there reinforcement.
• Draw a horizontal line of 1'8" ft and vertical line of 3'10" ft.
• Then use offset command give horizontal line offset at distance of 3'10"ft and vertical line offset at distance of 1'8"ft.
• Now we have a rectangled is formed.
• Again use offset command at distance of 1" inch for all four lines to inside of rectangle.
• Now use fillet command ar radius of 1" inch at corners of newly offseted lines.
• After that draw a circle dia of 2" inch at top left corner and copy it to the remaining three corners.
• Draw a line at centre of new offseted lines by using vertical as reference.
• And offset it at distance of 0.5" to the up and bottom.
• Attached those horizontal line by drawing vertical line and use fillet command at radius of 1" inch kind of ring is formed and delete the center we used as reference.
• After creating a middle ring then we'll go for up stirrups and bottom stirrups.
• Use offset command and give an offset at 11" inch for up stirrups and bottom stirrups.
• Both up and dow stirrups gives 1" inch radius fillet.
• Up one to the downward direction fillet and down stirrups to the upward direction fillet.
• The circles which drawn now fill with using hatch command and select solid in it.
• And copy that circles at nearer fillet where it is required.
• Now we go for hooks creation give hook at left corners two times to the downward direction. And one time again left corner in upward direction.
• Then write a three times to the left direction and 3 times to the right direction.
• Now C1 column is complete.
• Next we go for column C1a.
• In this column we'll start with name of the column as C1a with text height of 6" inch.
• Again draw middle line in second column and trim the line where it is not required.
• After that the first half portion divide into three parts and write first 9" X 24" , M25, 12-6mm dia.
• And last portion which is blanked then wirte there as 8 dia 3" & 8" CRS (1SET OF 3 STRS).
• Now in second we have to draw a column and there reinforcement.
• Draw a horizontal line of 1'8" ft and vertical line of 3'10" ft.
• Then use offset command give horizontal line offset at distance of 3'10"ft and vertical line offset at distance of 1'8"ft.
• Now we have a rectangled is formed.
• Again use offset command at distance of 1" inch for all four lines to inside of rectangle.
• Now use fillet command ar radius of 1" inch at corners of newly offseted lines.
• After that draw a circle dia of 2" inch at top left corner and copy it to the remaining three corners.
• Draw a line at centre of new offseted lines by using vertical as reference.
• And offset it at distance of 0.5" to the up and bottom.
• Attached those horizontal line by drawing vertical line and use fillet command at radius of 1" inch kind of ring is formed and delete the center we used as reference.
• After creating a middle ring then we'll go for up stirrups and bottom stirrups.
• Use offset command and give an offset at 11" inch for up stirrups and bottom stirrups.
• Both up and dow stirrups gives 1" inch radius fillet.
• Up one to the downward direction fillet and down stirrups to the upward direction fillet.
• The circles which drawn now fill with using hatch command and select solid in it.
• And copy that circles at nearer fillet where it is required.
• Now we go for hooks creation give hook at right corners two times to the downward direction. And one time left corner in upward direction.
• Now C1a column is complete.
• Next we go for column C2.
• In this column we'll start with name of the column as C2 with text height of 6" inch.
• Again draw middle line in second column and trim the line where it is not required.
• After that the first half portion divide into three parts and write first 9" X 24" , M25, 8-20mm dia(a), 4-12mm dia .
• And last portion which is blanked then wirte there as 8 dia 3" & 8" CRS (1SET OF 3 STRS).
• Now in second we have to draw a column and there reinforcement.
• Draw a horizontal line of 1'8" ft and vertical line of 3'10" ft.
• Then use offset command give horizontal line offset at distance of 3'10"ft and vertical line offset at distance of 1'8"ft.
• Now we have a rectangled is formed.
• Again use offset command at distance of 1" inch for all four lines to inside of rectangle.
• Now use fillet command ar radius of 1" inch at corners of newly offseted lines.
• After that draw a circle dia of 2" inch at top left corner and copy it to the remaining three corners.
• Draw a line at centre of new offseted lines by using vertical as reference.
• And offset it at distance of 0.5" to the up and bottom.
• Attached those horizontal line by drawing vertical line and use fillet command at radius of 1" inch kind of ring is formed and delete the center we used as reference.
• After creating a middle ring then we'll go for up stirrups and bottom stirrups.
• Use offset command and give an offset at 11" inch for up stirrups and bottom stirrups.
• Both up and dow stirrups gives 1" inch radius fillet.
• Up one to the downward direction fillet and down stirrups to the upward direction fillet.
• The circles which drawn now fill with using hatch command and select solid in it.
• And copy that circles at nearer fillet where it is required.
• Now we go for hooks creation give hook at right corners two times to the downward direction. And one time left corner in upward direction.
• Then write a 2 times to the left direction and 2 times to the right direction. Same goes for upward direction and downward direction.
• Now C2 column is complete.
• Next we go for column C2a.
• In this column we'll start with name of the column as C2a with text height of 6" inch.
• Again draw middle line in second column and trim the line where it is not required.
• After that the first half portion divide into three parts and write first 9" X 10" , M25, 8-16mm dia.
• And last portion which is blanked then wirte there as 8 dia 3" & 8" CRS (1SET OF 3 STRS).
• Now we for column making.
• Draw a horizontal line of 1'10" same vertically and for two times and draw a square.
• Then use offset command at distance of 1" inch for all four side.
• Use fillet command to the inside offseted lines with radius of 1"inch.
• Now use line command select centre of the square from each side and form rotated sqaure.
• After that use fillet command with radius of 1" inch.
• Copy the circle which we drawn before and copy it to inside square four corners.
• As well as copy it to the rotated square corners.
• Make a hook at rigth corner and middle of the rotated corner.
• Now C2a column is complete.
• Next we go for column C3.
• In this column we'll start with name of the column as C3 with text height of 6" inch.
• Again draw middle line in second column and trim the line where it is not required.
• After that the first half portion divide into three parts and write first 9" X 21" , M25, 12-16mm dia .
• And last portion which is blanked then wirte there as 8 dia 3" & 8" CRS (1SET OF 3 STRS).
• Now in second we have to draw a column and there reinforcement.
• Draw a horizontal line of 1'8" ft and vertical line of 3'10" ft.
• Then use offset command give horizontal line offset at distance of 3'10"ft and vertical line offset at distance of 1'8"ft.
• Now we have a rectangled is formed.
• Again use offset command at distance of 1" inch for all four lines to inside of rectangle.
• Now use fillet command ar radius of 1" inch at corners of newly offseted lines.
• After that draw a circle dia of 2" inch at top left corner and copy it to the remaining three corners.
• Draw a line at centre of new offseted lines by using vertical as reference.
• And offset it at distance of 0.5" to the up and bottom.
• Attached those horizontal line by drawing vertical line and use fillet command at radius of 1" inch kind of ring is formed and delete the center we used as reference.
• After creating a middle ring then we'll go for up stirrups and bottom stirrups.
• Use offset command and give an offset at 11" inch for up stirrups and bottom stirrups.
• Both up and dow stirrups gives 1" inch radius fillet.
• Up one to the downward direction fillet and down stirrups to the upward direction fillet.
• The circles which drawn now fill with using hatch command and select solid in it.
• And copy that circles at nearer fillet where it is required.
• Now we go for hooks creation give hook at right corners two times to the downward direction. And one time left corner in upward direction.
• Then write a 2 times to the left direction and same goes for upward direction and downward direction.
• Now C2 column is complete.

ANS 2:- Window Schedule

• Create drawing sheet first in unit select decimal.
• And in dimesion command also select decimal and all parameters as per standards.
• Now we will go for the converting black sheet into white by clicking on autocad symbol then click on option select display from the panel after that go for colors and select white and apply.
• First click on annotation then click on standards after that manage text style click on font name and select roman.shx and set current.
• Create a table of 5 columns and 6 rows.
• First column space between 4' ft and 2,3,4,5 having distance of 5.5'ft.
• In 1st column type with text height of 6" inch TYPE, WIDTH, SILL, LINTEL, NOS and LOCATION.
• In next column we have to write W1A, 1'-9", 3', 6'-7", 1, Toilet shaft side first floor.
• After that in 3rd column we have to write W1A, 1'-9.5", 3', 6'-7 3/4", 1, Toilet shaft side second floor.
• Then in 4th column we have to write W1A, 1'-9.5", 3', 6'-5 1/4", 1, Toilet shaft side third floor.
• And the last one we have to write W2, 2'-5 1/2", 3'-7.5", Beam bottom, 2, Toilet near courtyard first and second floor.

ANS 3:- Drawing Template

• Create drawing sheet first in unit select decimal.
• And in dimesion command also select decimal and all parameters as per standards.
• Now we will go for the converting black sheet into white by clicking on autocad symbol then click on option select display from the panel after that go for colors and select white and apply.
• First click on annotation then click on standards after that manage text style click on font name and select roman.shx and set current.
• Draw a horizontal line which having a length of 68' ft and vertical line of 7.5' ft.
• Then give an offset of by using horizontal line at distance of 7.5'ft and by using vertical line of offset it at distance of 68'ft.
• Now we have a rectangled in form, again use the offset command and iffset newly drawn rectangle at distance of 1" in to all four sides.
• After that use fillet command at radius of 0 degree and at fours newly drawn offseted rectangle.
• Now select left offseted line and use offset command and offset it at distance of 25' and again at 1" distnace.
• After that we have a column is formed.
• Now copy these new lines at distance of 18' ft after that we have a second column formed.
• Then use offset command at distance of 8.5' ft.
• After that two more columns are formed.
• In 1st column write Notes with multiline text at height of 5" inch.
• In next column draw two horizontal lines at distance of 1.5' ft with length of 17'-10".
• Then give offset of 1.5' ft between these two rows write Project and in second row write Architect.
• In 3rd and 4th column use offset command to offset horizontal line at distance 1.5' ft for five times.
• After that in 3rd column 1st row write Drawing title , 2nd row write drawing no, in 3rd row write issue date and the last one write revesion no.
• For 4th column wirte 1st row drawing list, in 2nd row write (AS/201802/A/901), 3rd row should be blank , in 4th row write date ,issued by and last row have Scale.
  

ANS 4:- List of drawing schedule

• Create drawing sheet first in unit select decimal.
• And in dimesion command also select decimal and all parameters as per standards.
• Now we will go for the converting black sheet into white by clicking on autocad symbol then click on option select display from the panel after that go for colors and select white and apply.
• First click on annotation then click on standards after that manage text style click on font name and select roman.shx and set current.
• Select line command draw a vertical line length of 38' ft. and select offset command and offset it at distance of 38'6" ft.Then join the points by drawing horizontal line which length of 38'6" from top and bottom.
• As we knoe that a rectangled is formed, use offset command and select top line then offset it at distance of 1' ft.
• Again offset it at a distance of 2'10"ft. Now we have two rows.
• After that copy the 1st row and paste it to the new offseted line and new row is been created.
• Do this same procedure until 29 row is form.
• Now we go for column making, use offset command and select the left vertical line then offset it at distance of 3'8" ft .
• And again select the new offseted line and offset it at distance of 12'2" ft then close the command.
• Trim the offseted line which intersecting at first 2 rows.
• Now we have three columns are formed.
• The 1st row which we created at the begining write there PROJECT with text height of 7" inches and In second row write LIST OF ARCHITECTURAL DRAWINGS with same text height.\
• Then we go for columns in 1st column write NO, in 2nd column write DRAWING NO and in last column write DESCRIPTION.
• In NO column we have 1 to 29 nos .
• In Drawing no column we have nos like IAS/201802/A/100, etc.
• And in last column description ciolumn we have descriptions of drawing like Ground floor Plan, etc.

ANS 5:- Beam Details

• Create drawing sheet first in unit select decimal.
• And in dimesion command also select decimal and all parameters as per standards.
• Now we will go for the converting black sheet into white by clicking on autocad symbol then click on option select display from the panel after that go for colors and select white and apply.
• First click on annotation then click on standards after that manage text style click on font name and select roman.shx and set current.
• Before we dive into the maiking of drawing this this drawing is not in actual dimesion some dimesion are assumed as per requirement.
• Draw a vertical line with length of 9'9" ft and offset it at distane of 2' ft.
• Now draw the horizontal line which are excluding the vertical line from both sides.
• Then cut section line which is zig- zag format.
• And copy it at above and below of column section.
• Then trim the unecessary lines, from top offset the horizontal line at distance of 2'7" ft and again new offseted line at distance of 2'7"ft.
• Use hatch command to the new offseted portion in ANS132 patter and below that hatch the potion in AR-CONC pattern then again the ANS132 at remainig portion.
• Name the drawing as SECTION with 6" height.
• Then we go annotation give the name to the upper portion as Brick Work ,TOB LEVEL +9" and the last one as GROUND LEVEL +/-100.
• Use the dimlinear for annotation 9" and 3" inch.