Creating Architectural and Structural model with 3D rendering using REVIT

Comparative study of different storey buildings for Seismic forces:Factors Influencing the Dynamic Characteristics of a Building: Mass Distribution – Heavier buildings generally have longer natural periods. Stiffness Distribution – Stiffer buildings have shorter natural periods and higher frequencies. Building Height &…

Model a 25 storey building on ETABS with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey height of 3 metres.:1. Model Creation Define grid spacing and storey levels (Plinth at 1.5m, 25 storeys…

Question 1:The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional area of the shear walls. Compare the three alternatives, taking into account the restraint…

Question 1:Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness and ductility.Ans:To assess the framing plan for earthquake resistance in the X and…

1. Differentiate Static analysis and Dynamic analysis with proper representing picturesStatic AnalysisDefinition: Static analysis is the process of examining code without executing it. It involves analyzing the source code or compiled code to identify potential errors, security vulnerabilities, and coding standards violations.Purpose:…

Identification of Cracks:Question 1:a)OBSERVATION:- We can clearly seen in the above image that the damage is done with beam but the column is perfectly fine.-  The damage is more caused to the beam than the column.- In this above image we can clearly see that the layer of concrete is completely crushed and reinforcement…

1. Design a Warehouse Building located in Chennai using STAAD Pro Connect Edition. The specification must be as follows:    Width 30mLength50mEave Height9mBay spacing6mSoil typeMediumSafe Bearing Capacity200 kN/m2Roof slope1 in 12Assume suitable sections for structural elements. Follow IS800:2007,…

1. Design a multi-storey Residential Building located in Bangalore using STAAD Pro Connect Edition. The specification must be as follows:      Building floors G + 6 + R Plan dimension B = 25m ,  L = 16m Storey Height h = 3.5m Soil  Hard soil Use Residential Purpose Safe Bearing Capacity 180 kN/m2 Maximum slab thickness…

### Task 1: Export Revit Models to Navisworks Cache File**Aim**: To export the architectural and structural models developed in Revit to Navisworks Cache files (.nwc) using the specified export settings.**Tools**:1. Autodesk Revit2. Export settings as discussed in class**Procedure**:1. Open Autodesk Revit.2. Load…

1. Creating Sinusoidal Points, Curve, and SurfaceSteps:Generate Sinusoidal Points:Use the Code Block node to define the range and sinusoidal function.Example: x = 0..10..#100; y = Math.Sin(x);Create points using the Point.ByCoordinates node.Create a Curve:Use the Curve.ByPoints node to create a curve from the generated…

1. 1. State the primary load cases to be considered for design.    2. What is One – Way slab?    3. What is the value of unit weight of structural steel and soil?    4. Name few sections that can be defined using Properties tab in STAAD Pro.    5. Define Primary Beams. 1.1.…

Q1.1. How will you assign Circular section to column? ANS : Go to properties in that select define property select circle and give the radius for the member and assign the defined circle to the member created Q1.2. How will you assign Unit system to a .std model file? ANS : While creating a model go to unit system…

1. 1. Write the steps involved to upload a .std file through web mail?Ans: Steps involved to upload a .std file through web mails are as follows; Open the STAAD pro software and locate the share option available on the introduction screen. After clicking on the share button, select send mail option. Then, browse for the.…

1)Select the type of structure you want to build from one of the three below        a. Multi Unit Residential Apartment        b. Office Buildings        c. School ANSWER:  My model represents a sea face residential building .    2) Assume reasonable…

1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level AIM:  To model a Ceiling from the architecture tab above the walls at the first-floor level. INTRODUCTION: The creation of Ceilings within Revit is a very…

NAME: PRAKASH.B PROJECT 2 AutoCADD Essential Task 1: AIM: To create a 3 dimensional model of the residential building  To create a rendered view of the developed model. To use materials and light setting. Procedure: Here in the project we are going to create a 3d model of a residential building. This is…

HALLENGE:-1 Q] Create a 3D Isometric View of the building with plan and elevation given.        AIM:- To create a 3D isometric view of the given building with plan and elevation.    INTRODUCTION:-  An isometric drawing is a 3D representation of an object,…

AIM: To create 3D model and view of: Furniture element Isolated footing AASTHO type girder Drop column with panel A wall Commands used: Extrude. Offset. UCS. Box. Union. Subtract. Move. 3d orbit. Loft. Sweep. Cone. Region. Boundary. PROCEDURE:  Open the AutoCAD, click on workspace switching and change it to 3d…

AIM: To create layout of plan and section, creating viewports, editing attributes and taking a plot. To create a kitchen layout in A4 sheet and take a plot To create Multiview ports for industrial section drawing, scaling it and taking a plot. COMMANDS USED: View Layout. Multiple View. Model Space. Paper Space. Scale.…

1) Create the layouts of the Kitchen and provide hatches pattern as shown. Also, use blocks whereverrequired. Provide appropriate dimensions in the plan. Assume the size of doors, appliances and othersas per the standards. Aim: To Create the Kitchen Layout and to  Also, use proper dimension techniques to dimension…

1. Create the templates as shown in Figures. Take the size of the title block as per industry standards oryou can assume it as per the size of the paper. Use text and attributes wherever required. After creatingthe title block you need to save it as a block with names: Custom1_titleblock and Custom2_titleblock,respectively.…

NAME: B.PRAKASH PROJECT: Design and Draft a layout of a residential building The following details: a. Plot Size: 60’x20’(18.3m x6m)  b. Orientation- Facing East    c. Develop the following: 1. Architectural Drawing (Floor Plan, Elevations, and Sections)          …

Aim: Sketch a G+1 floor residential plan, according to Vastu shastra. List down the names of the structural drawings required to be provided to the site for construction. Assume the sizes of the structural elements (Column, Beam, Slab, etc.,) and accordingly calculate the individual corresponding loads from the members…

AIM: To Calculate the Concrete Mix Design for M35 grade concrete with fly ash & M50 grade concrete without Fly ash   INTRODUCTION: Concrete mix design is the method of finding the precise proportion of cement, sand and aggregates for concrete to achieve the target strength in structures, therefore concrete…