Assembly of Yacht
The respective link for Radarmast and Assembly of Yacht is given below:
https://drive.google.com/drive/folders/1QJ25vCnenf5d_z35NGdUnWD0o2_H165a?usp=sharing
SURFACE AND SOLID MODELLING OF SUNSEEKER PREDATOR YACHT WITH ASSEMBLY
ABSTRACT
This Project involves surface and Solid Modelling and rendering of an sunseeker predator Yacht. In this modelling we used to go with certain parts like hull, superstructure,seats with good spa bed and with a garage.The Sun Seeker Predator Yacht is full modeled with solidworks 2016 and Renderd with solidworks visualize.
INTRODUCTION
A yacht is a sail or power vessel used for pleasure, cruising, or racing. There is no standard definition, so the term applies to such vessels that have a cabin with amenities that accommodate overnight use.
The term, yacht, originates from the Dutch word “jacht” which means “hunt”, and originally referred to light, fast sailing vessels that the Dutch Republic navy used to pursue pirates and other transgressors around and into the shallow waters of the Low Countries.
DESIGN OF METHODOLOGY
In full assembly of the Yacht model the upcoming parts are involved in Yacht;
- Propeller
- Radar
- Hull
- Garage Door
- Front Seat
- Middle Seat
- Rear Seat
- Super Structure
- Radar Mast
- PROPELLER
A propeller is a device with a rotating hub and radiating blades that are set at a pitch to form a helical spiral, that, when rotated, performs an action which is similar to Archimedes' screw. It transforms rotational power into linear thrust by acting upon a working fluid, such as water or air.
Features Involved:
- Revolve
- Cut Extrude
- Surface Loft
- Fillet
- Circular Pattern
- RADAR
Radar is a vital navigation component for safety at sea and near the shore. Captains need to be able to maneuver their ships within feet in the worst of conditions and to be able to navigate "blind", when there is no visibility at night or due to bad weather. In addition to vessel-based marine radars, in port or in harbour, shore-based vessel traffic service radar systems are used by harbormasters and coast guard to monitor and regulate ship movements in busy waters.
Features involved:
- Extrude
- Cut Extrude
- Fillet
- Mirror
- Sketch Driven Pattern
- Split Line
- HULL
The hull of a ship is the most notable structural entity of the ship. To define the hull, it can be said that it is the watertight enclosure of the ship, which protects the cargo, machinery, and accommodation spaces of the ship from the weather, flooding, and structural damage.
Features Involved:
- Project Curve
- Composite Curve
- Surface Loft
- Surface Extend
- Surface Trim
- Surface Fill
- Surface Knit
- Shell
- Boss- Extrude
- Cut Extrude
- Swept Boss
- Revolve Boss
- Dome
- Curve Pattern
- Linear Pattern
- Fillet
- Chamfer
- Mirror
- Split
- GARAGE DOOR
A Garage door is placed at the back side of the hull part, where either it can open manually or by an electric motor. Garage doors are frequently large enough to accommodate automobile and other vehicles. Small garage doors may be made in a single panel that tilts up and back across the garage ceiling.
Features Involved:
- Split
- Shell
- Text
- FRONT SEAT
Front Seat is placed at front of the hull part which is placed with the pillow and bed with good comfort
Features Involved:
- Project Curve
- Swept Surface
- Loft Surface
- Ruled Surface
- Surface Extend
- Surface Knit
- Extrude
- Mirror
- Cut Extrude
- Fillet
- Chamfer.
- MIDDLE SEAT
Middle Seat is placed at the rear side of the super structure with the center table and it made with the good bed part.
Features Involved:
- Extrude
- Surface Offset
- Cut Extrude
- Fillet
- REAR SEAT
Rear seat is also placed at the rear part of the hull part and is attached with the bed and it is attached with the flag and gate.
Features Involved:
- Curves
- Surface Loft
- Surface Rule
- Surface Knit
- Extrude
- Mirror
- Cut Extrude
- Pattern
- Swept Boss
- SUPER STRUCTURE
A superstructure is an extended construction of any building or platform that rises above the rest of the building or platform in a distinct manner. The word comes from a combination of two Latin words, the Latin prefix ‘super’ means in addition or above or in excess of, whereas the stem word ‘structure’ means to build or to heap up. Thus, superstructure means to add a construction to an already existing structure. In ships this is the name given to the part of the ship that emerges from the deck.
Features Involved:
- Curve
- Surface Sweep
- Surface Rule
- Surface Extend
- Surface Extrude
- Surface Trim
- Surface Fill
- Surface Knit
- Offset Surface
- Sweep base
- Extrude Cut
- Extrude Boss
- Fillet
- Chamfer
- Delete face
- Mirror
- RADAR MAST
Marine radars are X band or S band radars on ships, used to detect other ships and land obstacles, to provide bearing and distance for collision avoidance and navigation at sea. They are electronic navigation instruments that use a rotating antenna to sweep a narrow beam of microwaves around the water surface surrounding the ship to the horizon, detecting targets by microwaves reflected from them, generating a picture of the ship's surroundings on a display screen.
Features Involved:
- Extrude
- Revolve
- Cut Extrude
- Sweep Surface
- Fillet
- Chamfer
ASSEMBLY
The Hull is Fixed as base and the other parts are automatically fixed above the main deck surface. The mate conditions for Propeller and Radar are given such that to allow rotational motion and fixed at two directions. Suitable Appearances and Decals are added to provide the good appearance to the vessel.
Rendered image with backplate: