Analysis on a plate with a hole

Project:- Centrifugal Pump design and analysis Aim & Objective:- To create a 3D CAD model of a centrifugal pump and perform a flow simulation. The objective is to obtain the relationship between Pressure ratio and mass flow rate to study the pump behavior for different conditions. Introduction:-  A centrifugal…

Project Objective:- To create a 3D model of a flow bench and run a CFD flow analysis and obtain a plot of lift vs mass flow rate. A grid dependency test was done to show the effect of valve lift on mass flow rate.  Introduction:-  Computational Fluid Dynamics (CFD) is a branch of fluid mechanics that uses numerical…

Aim:- To simulate the flow over a cylinder for the conditions shown in the video. To start, run a baseline simulation and then calculate the Reynolds number. Then increase the Reynolds number by a factor of 20%, 40%, and 100% then run the transient flow simulation. Objective: Calculate the Reynolds number for different…

Aim:- To run a pipe flow simulation with an inlet Reynolds number of 100,1000 and 10,000. Objective:- To run an internal pipe flow simulation with Solidworks For each of these cases, the following conditions must be applied: Place line probes at 95%, 90% and 85% of the pipe length. Compare the normalized velocity profile…

Aim:- 1. Write a function that extracts the 14 coefficients and calculates the enthalpy, entropy and specific heats for all the species in the data file. this file is the NASA thermodynamic data provided. 2. Calculate the molecular weight of each species and display it in the command window. 3. Plot the Cp, Enthalpy…

Aim:- To write code in MATLAB to optimise the stalagmite function and find the global maxima of the function.   Introduction:- The genetic algorithm is a method for solving optimization problems that are based on natural selection, the process that drives biological evolution. The genetic algorithm repeatedly…

Aim:- To write code to fit a linear and cubic polynomial for the Cp data.  Introduction:- Curve fitting is the process of constructing a curve, or mathematical functions, which possess the closest proximity to the real series of data. By curve fitting, we can mathematically construct the functional relationship between…

Aim:-  To solve an ordinary differential equation (ODE)  and use the calculated information to animate the motion of the pendulum via MatLab.   Introduction:- Pendulums have many applications and were utilized often before the digital age. They are used in clocks and metronomes due to the regularity…

Aim:- The objective of this project is to calculate the thermal efficiency of the Otto cycle and plot the PV diagram   Introduction:-  The Otto cycle is a set of processes used by spark-ignition internal combustion engines. These engines a) ingest a mixture of fuel and air, b) compress it, c) cause it to react,…

Aim of the project:- To write a program in Matlab to simulate the forward kinematics of a 2R Robotic Arm Introduction:- Kinematics is the relationships between the positions, velocities and accelerations of the links of a manipulator. The forward kinematics is when the kinematical data are known for the joint…

Aim:-  To write a Matlab program to calculate drag force against a cyclist.   Abstract:- The objective of this project is to write two programs. One for plotting Velocity vs Drag force and another program to plot Drag Co-efficient vs Drag force. Firstly, the drag force must be calculated using a single value…

Abstract: - This project aims to perform a fatigue analysis on a bicycle crank arm using SolidWorks and find out the number of cycles it will take before the part to reach failure. The Stress Life (SN) method was used since it is based upon standard material test to failure. Several parameters were changed, these parameters…

Abstract:- The aim of this project is to perform a frequency analysis on a rotating shaft, from there we need to determine the critical frequencies and the mode shapes. 5 Mode Shapes were simulated and analysed. Introduction:- Frequency is the number of occurrences of a repeating event per unit of time. The formula…

Abstract:- The aim of this project is to perform a frequency analysis on a rotating shaft, from there we need to determine the critical frequencies and the mode shapes. 5 Mode Shapes were simulated and analysed. Introduction:- Frequency is the number of occurrences of a repeating event per unit of time. The formula…

Abstract:- To Perform a static analysis on two models of a plate with holes via SolidWorks, one analysis for a plate with one hole and one analysis for a plate with three holes. Finally, compare the obtained results between the two plates. Introduction:- When loads are applied to a body, the body deforms and the effect…

Abstract:- For this project, the main objective is to carry out a buckling analysis on a Cyclonic separator stand. After the initial analysis, a metallic stiffener will be sketched and added to the stand and another buckling analysis will be simulated to find the change in the buckling Factor of Safety. Finally, a design…

Abstract: - For this project, there will be three different types of beams (Rectangular beam, I- section beam and C- section beam). These beams will be extruded by a length of 400mm. From there, the beams will be simulated using the Finite Element Analysis techniques. A fixed fixture and a force of 1500N will be acting…