Aim: Detailing of shear wall Procedure: Step 1: The provided ETABS model is analysed and the shear wall design is run as shown in the figure below. Step 2: The mentioned shear wall is labelled as P1. The design results of pier P1 is extracted as shown below. From the obtained results, it can be seen that a boundary zone…
udhaya nageswaran
updated on 10 Jul 2022
Project Details
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Read more Projects by udhaya nageswaran (43)
Week 3 Challenge
1. 1. State the primary load cases to be considered for design. ANS : The primary load cases to be considerd for the design are the Dead load Live load / Imposed load Wind load Earth quakeload 1.2. What is One – Way slab? ANS : One - way slab The ratio of the longer span to the shorter span is greater than 2 is know…
05 Aug 2022 06:15 PM IST
Week 2 Challenge
QUESTION 1 1. How will you assign the Circular section to the column? AIM To assign a circular section to the column INTRODUCTION Columns are the vertical member in the structure that can be of varying sizes in dimension The circular section of the column is provided on the upper floor of the building for the better load…
01 Aug 2022 06:31 PM IST
Week 1 Challenge
1. a) AIM : Write the steps involved to upload a .std file through web mail? Introduction : STAAD pro ( Structural Analysis and Deign program is the abbrivation for the STAAD it is the connected version new version used to analize the RCC structure and steel structure by using this software ) It Include…
29 Jul 2022 01:12 PM IST
Project 2_Design & Analysis of a Hostel building at Guwahati, Assam
ANSWER:- Aim:- To design and analysis of G+3 Hostel building in ETABS and Foundation in CSI SAFE. Introduction:- The procedure for analysis and design of a given building will depend on the type of building, its complexity, the number of stories etc. First the architectural drawings of the building are studied,…
19 Jul 2022 05:19 PM IST
Design of Shallow Foundation (Isolated Footings)
Aim: To design a square footing for a column size of 400x400 Given data: Size of the Column = 400*400 Compression axial load = 2000 KN Safe Soil Bearing Capacity (Safe SBC) = 150 KN/m2 Grade of concrete = M25 Procedure: Step 1: Determination of the size of the footing Lets assume the Self weight of…
19 Jul 2022 05:15 PM IST
Foundation Design using SAFE
1. AIM: To Analyze and designthe isolated footing from week 11 challenge on SAFE To verify the size, depth and steel provided as per calculations. INTRODUCTION: CSI SAFE (Slab Analysis by the Finite Element Method) is the best tool for designing concrete slabs and foundations. SAFE provide easiness to engineer towards…
11 Jul 2022 05:45 PM IST
Structural Modelling using Etabs 2018
ANSWER:- Aim:- To model and analyze the G+7 residential building from the given architectural drawings using the ETABS 2018. Introduction:- ETABS is an engineering software product that caters to multi-story building analysis and design. Modeling tools and templates, code-based load prescriptions, analysis methods…
10 Jul 2022 05:50 PM IST
Analysis & Design of RCC shear walls in the model using ETABS
Aim: Detailing of shear wall Procedure: Step 1: The provided ETABS model is analysed and the shear wall design is run as shown in the figure below. Step 2: The mentioned shear wall is labelled as P1. The design results of pier P1 is extracted as shown below. From the obtained results, it can be seen that a boundary zone…
10 Jul 2022 05:48 PM IST
Reinforcement detailing of Columns from ETABS output
Aim: To Providing details of longitudinal reinforcement for the two columns from foundation to terrace level. Step 1: 1) Open a G+4 Etab file 2) Click the Concrete Frame Design tool 3) Select the Display Design Info option 4) Choose design output as Longitudinal Reinforcement Step 2: 1) After Selecting the Longitudinal…
10 Jul 2022 05:46 PM IST
Reinforcement Detailing of Beams from ETABS output
Reinforcement Detailing of Beams from ETABS output QUESTION:- Detail design of beams in Etabs 2018.The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment ResistingFrame. The following challenge deals specifically with two continuous beams in the 1st floor. …
10 Jul 2022 05:45 PM IST
Project 1_Comparative study of different storey buildings for Seismic forces
AIM: TO MODEL AND ANALYZE MULTIPLE BUILDINGS WITH DIFFERENT FLOOR LEVELS AND DESIGN PARAMETERS USING ETABS SOFTWARE AND COMPARE THE RESULTS TO UNDERSTAND THEIR OVERALL SEISMIC BEHAVIOUR. INTRODUCTION: The structural…
10 Jul 2022 05:43 PM IST
Modelling of 25 storey building with the specified properties using ETABS
Aim: to model and analyse a 25 storey building with given specifications and to cross check the parameters as per IS 1893 provisions. Procedure: Open the ETABS software.Click the file menu and choose to create a new model option.After choosing a new model a dialogue box will appear as model intialization.Choose the built-in…
10 Jul 2022 05:39 PM IST
Conceptual design of a building with columns and shear walls
Question 1: The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm inthickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional area of the shear walls.Compare the three alternatives, taking into account…
01 Jul 2022 08:14 AM IST
Concept on positioning of Columns
Question 1:Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots arecolumns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness and ductility. Answer:1.SymmertryHaving a look over the aspects of symmetry of the framing…
01 Jul 2022 08:11 AM IST
Calculation of Stiffness in Structural elements
1.AIm: Compute lateral stiffness of the one story frame with an intermediate realistic stiffness of the beam. The system has 3 DOFs asshown. Assume L = 2h and El = El Lateral stiffness of the one story frame: This structure can be analyzed by any of the standard methods, including momentdistribution. Here we use the definition…
29 Jun 2022 05:32 PM IST
Identification of Cracks
1) What is the mode of failure or damage of the beams in the figure above? Would you characterize the case as damage or as afailure? Are the damages repairable? Elaborate. a)This crack will be formed due to the flexural failure of a beam. The flexural strength, known as modulus of rupture, bendstrength, or fracture strength,…
22 Jun 2022 05:18 PM IST
Creating Conceptual mass in REVIT and Creation of Sinusoidal curve and a Parametric stadium using Dynamo
1, Aim:To create a set of sinusoidal points, a curve and a surface out of the curve using dynamo. Procedure: Initially, open the architecture template of Revit software and go to manage tab.In manage tab select the dynamo. Then dynamo window opens and then go to new option. Now, start the process by inserting three integer…
21 Jun 2022 06:06 PM IST
Usage of Navigation tool , Timeliner and Clash Detection test using Naviswork
1 .Aim: Using the Architecture/ Structure Project file developed and exporting the Revit architecture and structure model to NavisworksCache file following the export settingsCommands used:ExportFile3D view. Procedure: 1. Opening the Architectural models of previous weeks and viewing in 3D view2. Clicking on export option…
21 Jun 2022 05:31 PM IST
Structural analysis of a buidling using Robot Structural Analysis
1) What are HVAC systems? Why are they essential in the modeling of buildings?ans)HVAC system is basically an assembly of various types of equipment installed together to provide heating and cooling alongwith indoor climate control. HVAC systems involve mechanical, electrical and I & C components to provide comfort…
21 Jun 2022 05:19 PM IST
Creating a Wardrobe detailed drawing, Floor Plan, Kitchen Layout and Column Detail using AutoCad
1.AIM:To draw the elevation and details of a wardrobe as shown in the figure. After sketching, you need to provide the dimensions and textwith the use of layers. PROCEDURE: STEP 1:Units are set to mmLimits and limax are also setZoom command is also used STEP 2:In the command line type rec > 2800,2600In the command line…
21 Jun 2022 08:31 AM IST
Creating various 3D Models like Furniture, Footing, Girder, Column drop with panel and Gable Wall in AutoCad
1.AIMTo create a 3D Furniture elements using the various commands in Auto CAD. INTRODUCTION BY 3D VIEWThe process of creating a mathematical representation of any surface of an object in three dimensions by using specialsoftware.A 3D model can even be represented as a two dimensional image by using the 3D rendering process.It…
21 Jun 2022 08:06 AM IST
Preparing Schedule & Cost Estimation for a building using REVIT
1.Aim:To list the shortcut keys for the following:a. Using 3D model create a section boxb. To create similar doors and windows in a floor plan layoutc. To reduce the thickness of lines visible in plan viewsd. To apply override settings to a floor in the model section viewe. To increase the range of visibility in a plan…
20 Jun 2022 05:54 PM IST
Creating Architectural and Structural model with 3D rendering using REVIT
Q1)AIM:Select the type of structure you want to build from one of the three below:a. Multi-Unit Residential Apartmentb. Office Buildingsc. School.ANS) OFFICE BUILDING Q2)AIM :Assume reasonable assumptions for geographic and location details for your project modeling. Based on assumptions and type ofstructure selected…
19 Jun 2022 05:49 PM IST
Usage of Collaborate tool in REVIT
1) Open an architectural template. Using the Manage tab set project base point and project shared coordinates for the project. Aim: to set project base point and project shared coordinates for the project. procedure: To create project shared coordinates: Open architectural tab.Open Manage tab.Click on project coordinates…
19 Jun 2022 03:23 PM IST
Creating Levels, Grids, Layout and model elements for a residential unit using REVIT
1) What is BIM? Summarize the features of BIM and benefits of using BIM over 2D CAD tools.A) Building Information Modeling(BIM):-BIM is an acronym for Building Information Modeling or Building Information Management.It is a highly collaborative process that allows architects, engineers, real estate developers, contractors,…
18 Jun 2022 05:51 PM IST
Introduction to National Building Code and Steps in a Construction project
1) Why are building codes or standards essential for the modeling/ efficiency of drawings in Revit ?ans)A building code (also building control or building regulations) is a set of rules that specify the standards for constructed objectssuch as buildings and nonbuilding structures.Building codes specify minimum standards…
17 Jun 2022 05:33 PM IST
3D Creation of Celing, Roof, Architectural plan, Structural plan, Sectional view, Elevation view and Camera specific view for a house plan using REVIT
1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above thewalls at the first-floor level. AIM:- To model a Ceiling from the architecture tab above the walls at the first-floor level. INTRODUCTION:-The creation of Ceilings within Revit is a very similar…
17 Jun 2022 05:21 PM IST
Creation of Multiple viewports, Scaling the drawing and setting in Template in AutoCad
1. AIM:To create the layout of the plan and section A of the project in challenge 7 using the template Tutorial -mArch.dwt INTRODUCTION:A layout template is a layout imported from a DWG or DWT file. The program has sample layout templates to use when we design anew layout environment.When you create a layout based on a…
16 Jun 2022 05:26 PM IST
Creating Walls, Partition walls and Floors for a residential layout using REVIT
1) Use the project file created from Week 2. Use it for this assignment. Based on your layout from week 2, using floor tool underarchitecture tab and select the floor with appropriate material and thickness using the property browser create a layout in theGround floor Level. Align the floor plan with grids created from…
14 Jun 2022 06:07 PM IST
Introduction to REVIT concepts
1. 1) From the file menu, create a new project (Structural / Architectural / Construction template ) and name the projectappropriatelyAIM:- To create a new project from the file menu and need to name the project appropriately. INTRODUCTION:-For creating a project, select a template from the Projects list or the New…
13 Jun 2022 06:29 PM IST
Creating 3D Isometric view of various structural elements in AutoCAD
AIM: TO DRAW THE GIVEN DRAWING USING AUTOCAD. PROCEDURE: STEP 1: IN THE COMMAND PROMPT TYPE UNITS AND SELECT DECIMAL UNITS. STEP 2: IN THE COMMAND PROMPT TYPE USING LINE . IN THE COMMAND PROMPT TYPE USING OFFSET IN THE COMMAND PROMPT TYPE USING CIRCLE IN THE COMMAND PROMPT TYPE USING TEXT. IN THE COMMAND PROMPT TYPE…
08 Jun 2022 05:33 PM IST
Creating Kitchen layout, Hatching of Architectural elements and sectional view of an Industrial Building in AutoCad
1. AIM: TO DRAW THE GIVEN DRAWING USING AUTOCAD. PROCEDURE: STEP 1: IN THE COMMAND PROMPT TYPE UNITS AND SELECT DECIMAL UNITS. STEP 2: IN THE COMMAND PROMPT TYPE USING LINE . IN THE COMMAND PROMPT TYPE USING OFFSET IN THE COMMAND PROMPT TYPE USING CIRCLE IN THE COMMAND PROMPT TYPE USING TEXT. IN THE COMMAND PROMPT…
07 Jun 2022 05:52 PM IST
Creating Bar Bending schedule, Different Door types, and Creation of standard drawing templates using AutoCad
1. AIM: TO DRAW THE GIVEN DRAWING USING AUTOCAD. PROCEDURE: STEP 1: IN THE COMMAND PROMPT TYPE UNITS AND SELECT DECIMAL UNITS. STEP 2: IN THE COMMAND PROMPT TYPE USING LINE . IN THE COMMAND PROMPT TYPE USING OFFSET IN THE COMMAND PROMPT TYPE USING CIRCLE IN THE COMMAND PROMPT TYPE USING TEXT. IN THE COMMAND PROMPT…
07 Jun 2022 05:22 PM IST
Project 1 _Creating an Architectural plan for the provided plot size and develop relevant basic structural drawings
AIM: TO DRAW THE GIVEN DRAWING USING AUTOCAD. PROCEDURE: STEP 1: IN THE COMMAND PROMPT TYPE UNITS AND SELECT DECIMAL UNITS. STEP 2: IN THE COMMAND PROMPT TYPE USING LINE . IN THE COMMAND PROMPT TYPE USING OFFSET IN THE COMMAND PROMPT TYPE USING CIRCLE IN THE COMMAND PROMPT TYPE USING TEXT. IN THE COMMAND PROMPT TYPE…
06 Jun 2022 06:32 PM IST
Creating a Layout, Section and Elevation with dimensions using AutoCad
AIM: TO DRAW THE GIVEN DRAWING USING AUTOCAD. PROCEDURE: STEP 1: IN THE COMMAND PROMPT TYPE UNITS AND SELECT DECIMAL UNITS. STEP 2: IN THE COMMAND PROMPT TYPE USING LINE . IN THE COMMAND PROMPT TYPE USING OFFSET IN THE COMMAND PROMPT TYPE USING CIRCLE IN THE COMMAND PROMPT TYPE USING TEXT. IN THE COMMAND PROMPT TYPE…
06 Jun 2022 05:57 PM IST
Project 2_Creating a 3D rendered model for a Residential Building in AutoCad
If you have completed the previous lessons in this level, you now have the tools to create a large variety of objects in 3D. This lesson is designed to show how to create simple building in 3D from start to finish. The same process can be used to build more complex buildings as well. Start by creating this building and…
05 Jun 2022 06:12 PM IST
Creating a Residence Layout, Seating plan, Toilet and Utility room plan using AutoCad
AIM: TO DRAW THE GIVEN DRAWING USING AUTOCAD. PROCEDURE: STEP 1: IN THE COMMAND PROMPT TYPE UNITS AND SELECT DECIMAL UNITS. STEP 2: IN THE COMMAND PROMPT TYPE USING LINE . IN THE COMMAND PROMPT TYPE USING OFFSET IN THE COMMAND PROMPT TYPE USING CIRCLE IN THE COMMAND PROMPT TYPE USING TEXT. IN THE COMMAND PROMPT TYPE…
03 Jun 2022 05:15 PM IST
Creation of Column Schedule and Drawing Template using AutoCad
AIM: TO DRAW THE GIVEN DRAWING USING AUTOCAD. PROCEDURE: STEP 1: IN THE COMMAND PROMPT TYPE UNITS AND SELECT DECIMAL UNITS. STEP 2: IN THE COMMAND PROMPT TYPE USING LINE . IN THE COMMAND PROMPT TYPE USING OFFSET IN THE COMMAND PROMPT TYPE USING CIRCLE IN THE COMMAND PROMPT TYPE USING TEXT. IN THE COMMAND PROMPT TYPE…
03 Jun 2022 05:13 PM IST
Drafting of various geometries using Chamfer, Fillet tool in AutoCad
Drafting of various geometries using Chamfer, Fillet tool in AutoCad: Aim: To draw the given drawing using autocad software: Procedure: Step 1: In the command prompt type pl(poliline). In the command prompt type start point 3.0 In the command prompt type @1.20 In the command prompt type @0.80 In the command…
29 May 2022 04:59 PM IST
Creation of geometries by Coordinate system methods using AutoCad
GEOMETRIC SYSTEMS BY COORDINATE METHODS
28 May 2022 06:04 PM IST
Creating a Floor plan, Footing detail and Isometric view using AutoCad
FLOOR PLAN,FOOTING,ISOMETRIC VIEW
28 May 2022 05:43 PM IST
Sketch a G+1 residential plan according to Vaastu Shastra and Calculation of Loads as per IS code
Aim: Sketch a G+1 floor residential plan, according to Vastu shastra. List down the names of the structural drawings required to be provided to the site for construction. Assume the sizes of the structural elements (Column, Beam, Slab, etc.,) and accordingly calculate the individual corresponding loads from…
09 May 2022 05:39 PM IST
Project on Concrete Mix Design for various grades of Concrete
STIPULATIONS FOR PROPORTIONING OF M35 GRADE CONCRETE This section contains specifications for the materials and requirements for the concrete to be manufactured. The specific gravity of Fly ash is 2.1 to 3, while the specific gravity of GGBS is 2.85. Use the appropriate specific gravity value based on the type of…
05 May 2022 05:19 PM IST