Advanced Sheet Metal Design Using NX Cad Challenge_1_Casing Design

    Final project - Door trim Inner Panel Role of plastic in the automobile industry: The use of polymers as plastics in the construction of automobiles has continued to grow over the last decades. Nowadays they are the second most commonly found in cars. Here are four reasons why plastic is used in car manufacturing:…

1. All the individual parts are modeled in the part design workbench with appropriate dimensions. 2. They are put in one assembly. 3. Applied with necessary constraints on it.  

1. For the given Class A surface dessign. 2. The Class B surface is created . 3. Class C surface is also created. 4. Finally the dog is created using the master section. 5.At last it is draft analysed.

1. For the Given Class A surface draft analysis is done on it. 2. By offsetting the Class B surface, the fillets which were failing were recreated. 3. Finally by using the reference to the surface of method/ by draft direction method there is a class C surface creation done. 4. Wherever required the heat stakes and locator…

1. For the Given Class A surface draft analysis is done on it. 2. By offsetting the Class B surface, the fillets which were failing were recreated. 3. Finally by using the reference to surface ot method/ by draft direction method there is a class C surface creation done. 4. Finally its is converted to plastic part and…

1. Taking the class A surface draft analysis is done to check it. 2. Then the class B surface offset is done. 3. Then the Class C surface is done w.r.t class A surface. 4. Then the closed body surface is done. 5. Finally converted to the closed body.   

1. From the given class A surface. It is checked for draft analysis. 2. The the class B offset is done, fillets that are failing are recreated. 3.Then considering the Class A surface, Class C surface sweep is done . 4. Finally the closed surface is done with surface A+ B - C . 5. Alast its is converted to closed body.

1. From the given switch bezel design. 2. From the class A, B, C surfaces the parting surface is created. 3. The core and cavity half are created. 4. The core and cavity are converted to the closed body and are separated from each other. 4. Finally the parting line and surface are shown  

1. The given class A surface is checked for draft analysis. 2. Then the Class B offset is done, wherever the fillets are failing it is created and by extracting the adjacent faces, extrapolate and finally trimmed to get the edge. then the measured value of the fillet from class A is applied to the Class B surface. 3. Then…

1. For the given class A surface, the tooling axis is created and it's checked for draft analysis. 2. Then the class B surface is created by using various options like offset, split, trim etc. 3. Then the Class A surface is trimmed with Class B surface to get the closed surface. 4, Finally the closed body is applied to…

1. The given class A surface is checked for draft analysis. 2. Then the B surface is created by extracting the flat surface, offset, untrim the same surface. 3. Then the C surface is created selecting the class A surface. 4. Finally the trim is done along the surface A + c - B surfaces.  

Aim - Design hood outer panel, inner panel and necessary reinforcements by following master section mentioned with design parameters. Submit assembly of hood outer panel, inner panel, latch and hinge reinforcements. With detailed report of Hood Design which includes a detailed explanation about hood and its components,…

Aim -Tail Gate Design- About –  A tail gate is also called as hatch. Its usually a door at rear vehicle that can be opened and closed. It’s mounted on the rearrest part of 4-wheel car with the help of hinge. It’s connected to gas stay or electric motor drive for easy opening or closing over the sides.…

Aim – Car roof design, internal support/strength components design with the help of given data. Also, to calculate the Heat distortion load and Snow load on the car roof and check its adaptability. About – The first iteration of the sun-roof dates back to the early 20th century when horse carriage inspired…

Use the Section from your Hood design and calculate the section modulus using the formula S = I/y, Come up with a new section that has improved the section modulus of the previous section and mention what change you made that has increased the strength. About Section Modulus - Section modulus is a geometric property for…

From the master section given below of side fender , create drip area for sill mounting, bumper mounting, A pillar mounting according to engineering standard concept. Image of side front fender and rear side fender It is also called as quarter panel it is the part which is in between the front bumper and the front passenger…

Write one page about Underbody coating and its purposes. Underbody coating is usually a dense cladding (often based on rubber) applied uniformly to the undercarriage of the automobile. It is normally sprayed or painted on when the car is just out of the dealership and is clean.  The main purpose of undercoating is…

Benchmark with presently available cars in the market for the following case. Mr. D.S. Pughazhyendhii is a married man who lives in Bangalore which is a highly crowded city. His Family comprises five members including his wife, five-year-old boy, his father, and his mother. He visits his native place Madurai which…

Title of the project – Advanced Sheet Metal Design Using NX Cad - Metal bracket-II Objective – To obtain a specified sheet metal bracket and to apply various sheet metal feature as per requirement and observing final desired output. Introduction – NX sheet metal design incorporates material and process…

Title of Project – Advanced Sheet Metal Design Using NX Cad – Bracket. Objective- To create a bracket from given 2D drawing and applying various sheet metal features on it. Introduction – NX sheet metal design incorporates material and process information in sheet metal-specific modelling features:…

Title of the Project – Advanced Sheet Metal Design Using NX Cad - Odd Shaped Enclosure. Objective – To show the recommended workflow procedure to design a Sheet Metal part of Odd Shapes. Introduction – NX sheet metal design incorporates material and process information in sheet metal-specific modelling…

Title of Project –  Advanced Sheet metal design using NX CAD – Box Assembly Objective – TO design a sheet metal box assembly using Siemens NX Sheet metal application. Introduction – NX sheet metal design incorporates material and process information in sheet metal-specific modelling features: bends, flanges, tabs, cut-outs,…

Title of Project – Advanced Sheet metal design using NX CAD – Casing Design Objective -  To design a sheet metal casing design using Siemens NX Sheet metal application. Introduction – This was first developed by Unigraphics as high-end CAD/CAM/CAE software, later was owned by by Siemens in 2007.…

1. Radar Mast - Various directional views, Feature tree, Features are continued in row wise,     -------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Title – Report on Design of Yacht model assembly.…

Title – Report on Design of American Chopper. Objective – The main objective is to learn how to model a part, assembly of created parts and to create a photo realistic view using photo view 360* & visualise in SolidWorks. Introduction – It contains detailed explanation of designing an American chopper…

Objective - To write a code in MATLAB to parse the NASA Thermodynamic file and to calculate the various thermodynamic properties(Cp,H,S) What to do & find - \"Parse\" is the break down the given set of data or sentence into its component parts and describe there syntactic roles. In this dataset we have stream…

Genetic Algorithm Objective - Finding the Global maxima for Stalagmite function in MATLAB using optimization method. What is Genetic Algorithm? Genetic Algorithm (GA) is a search-based optimization technique based on the principles of Genetics and Natural Selection. It is frequently used to find optimal or near-optimal…

Objective - To write program to obtain a curvefit for Linear and Cubic polynomials. Explanation - Curve fitting is the process of constructing a curve or a mathematical function that has the best fit to a series of data points, possibly subject to constraints. Curve fitting can involve either interpolation,…

Objective - To understand the motion of simple pendulum using MATLAB. Explanation -  A simple pendulum consists of a mass m, string of length l which is attached to the mass, where one end of string is fixed and the other end is freely suspended where the mass is attached. When the ball(mass) in equilibrium is…