SURFACE WRAPING ENGINE, TRANSMISSION AND GEARBOX

OBJECTIVE : To simulate a crash test for a crash box for which mesh is given. Compare the accelerations and stress/strain plots of 1.2/1.5mm crashboxes.  GIVEN PARAMETERS : 1. Material for the crashbox is steel.    2. Thickness of the crashbox is 1.2mm.    3. Initial velocity…

OBJECTIVE: To conduct drop test for a cell phone on a plate wih intial veocity in LS Dyna. PROCEDURE: Steps: 1. Material Creation 2. Section Creation 3. Assigning material to corresponding section 4. Assigning boundary condition and intial velocity 5. Creating contact between master and slave 6. Defining Termination point…

AIM : To solve a non linear static problem by both explicit and implicit analysis. Given Parameters : A simple bar in tension as shown in Figure 1. Suppose that the force in the bar is a nonlinear function of the displacement F(u) = u3+9u2+4u                    …

Aim : Convert given measurements into different system of units and finding their corresponding conversion factors. Measurements given : MASS 1kgLENGTH 1mTIME 1sFORCE 1NSTRESS 1PaENERGY 1NmDENSITY 1Kg/m3YOUNG'S Modulus  210GPaVelocity 56.33KMPHGRAVITY 9.8m/s2 System Of Units : Kg cm ms Kg cm s gm mm ms kg m s…

SOLIDWORKS Visualization is not supported in my PC. So I completed rendering upto the solidworks visualization and attached my rendered pics and chopper assembly files. https://drive.google.com/file/d/1WxDjm5FZO1X6qw0IPDMaTOYDIXKflh1K/view?usp=sharing

Objective: Perform geometry clean up and mesh the model for structural analysis with a target element size of 5mm for the given Ip Substrate models. Procedure: * Open one IP substrate model and then open quality citeria and got to presentation parameters tab then click on the check box Draw cons in PID, MID ....…

OBEJECTIVE : Create a surface mesh for a given cylinder. PROCEDURE : 1. Convert model into PID mode. 2. Check for geometric errors. 3. Boundary faces has been assigned. 4. Module is changed to MESH module from TOPO module. 5. Mesh has been created using SPOT MESH option. ELEMENT TYPE - triangle   ELEMENT SIZE…

Objective: Mesh the interior plastic component of the side door of a passenger vehicle with given quality criteria. After meshing assign thickness and check if the geometry is captured properly. 1. Take the mid-surface manually, mesh the geometry with quality. 2. Take auto mid-surface and mesh the geometry with quality.…

HOOD: The hood or bonnet is the hinged cover over the engine of motor vehicles that allows access to the engine compartment. Hoods are typically made out of steel, but aluminium is rapidly gaining popularity with auto companies. Aftermarket manufacturers may construct hoods out of fiberglass, carbon fiber or…

Surface Wrap:   The surface wrapper can be used to provide a closed, manifold, non-intersecting surface when starting from poor quality CAD data. It is typically used when the imported surface includes problems such as: multiple, intersecting parts missing data in the form of holes and gaps surface mismatches double…

BMW M6: The BMW M6 is a high-performance version of the 6 series coupé/convertible, designed and developed by the motorsport division of BMW. The BMW M6 was based on the subsequent generations of the 6 series. The BMW M6 concept made its debut at the 2005 Geneva Motor Show. The M6 shared the same…

TURBO CHARGER: A turbocharger, colloquially known as a turbo, is a turine-driven forced induction device that increases an internal combustion engine's efficiency and power output by forcing extra compressed air into the combustion chamber. Turbocharger performance influences all important engine parameters,…

https://drive.google.com/file/d/1jj2wCBoxRKK9ze7HQuv09RsTiqDSeQzQ/view?usp=sharing

https://drive.google.com/file/d/1pdJgpACC5wQEcJKASwppB0eH2EdHmDCS/view?usp=sharing

https://drive.google.com/file/d/109XTf3r2r79A3LQdYvnFo6OQo8hAiSIP/view?usp=sharing

https://drive.google.com/file/d/1b14zMyZzELCONdQq0M6aMcPNUWuuukug/view?usp=sharing

https://drive.google.com/file/d/1dJr2t6PmojiJTo6oXRyKfe8nUSiR2xU5/view?usp=sharing

https://drive.google.com/drive/folders/12AOWmOkTRf2yF-qXFcLRZrH6X62Ku_Tn