CASE STUDY

radar mast

Assembly

Rendering

OBJECTIVE:- To Create connector and Attach the various parts of the given model  1. Right_Rail_2 & Front_truss_1:- Seam-Quad 2. Left_Rail_2 & Front_truss_1:- Quad elements 3. Front_truss_2, Front_truss_1 & Right_Rail_1:- Spot weld with 3 Layers and 5 mm…

OBJECTIVE:- To create a 3D meshing of the component using hypermesh. And attain the required quality. QUALITY CRITERIA:- Elements sizes: Min- 2mm, Target- 5mm, Max- 7mm  Tet collapse: 0.10 to 0.15 PROCEDURE:- STEP-1: Delete the two Solid component by using F2 as the shortcut key from keyboard, Select…

AIM- To mesh the given Car's Hood. TOOL USED-HYPERMESH GIVEN QUALITY CRITERIA- S.N Quality Criteria  Value  1 Aspect Ratio  5 2 Skewness 45 3 Warping 15 4 Taper      0.5 5 Min. Length 2mm 6 Max. Length 8mm 7 Min angle Quad 45 8 Max angle Quad 135 9 Min angle Tria 20 10 Max angle Tria 120 10…

AIM- Creat 1D elements on the following component with given cross-section and DOF STEPS- 1. Import the given model as shown- 2. Extract the mid surface out of it- Midsurface is 2D element, extracted to represent the 3D surface.  It can be done only on surface with uniform thickness. Whenever we mesh a 3D model,…

AIM- To increase the section modulus of a given hood by necessary changes TOOL USED- NX CAD MATERIAL USED- STAINLESS STEEL AISI 302 INTRODUCTION- Section modulus is a geometric property for a given cross-section used in the design of beams or flexural members. Other geometric properties used in design include area…

AIM- To design back door of a car. TOOL USED- NX CAD BACK DOOR- It is a component used for entry and exit of the commodity.It is also responsible for safety purpose during rear head collision. It can be either operated manually of with the help of pneumatic power. It is mosly made up of steel as a material which increases…

Objective- 1. For the given Car Roof styling, design and develop the essential flanges and reinforcements, namely the Ditch Area, Front Roof Rail, Rear Roof Rail, Centre Roof Rail and Bow-Roofs. 2. Do a curvature study on the roof and perform calculations for Heat Distortion and Snow load criterion to determine and justify…

AIM-  The aim is to design the Drip Area, Sill mount area, bumper mount region, and A-pillar mount Region. THEORY- FENDER- Fender covers a wheel, traditionally to prevent water and mud spray, but now also for aerodynamic purposes. Bumper protects the body from small impacts to the front or rear of the vehicle.Sticky…

THOERY- Wheel arch is an arch-shaped cavity in the body of a vehicle, which houses a wheel. It has two important functions. It serves for the safety of pedestrians and other cars because the wheel is situated in the body of a vehicle. FRONT FENDER :         It is a BIW component whose main purpose is…

Design of a hood of a car using euro ncap

Aim:   To design Hood with the following requirements Design Outer Panel with the Hem Develop the Inner Panel Develop all the Necessary Reinforcements Mirror and position the Hinge & Striker Provide Mastic Data Provide the required Emboss definition     Tool used- NX 12 Theory- A car hood also referred…

1. What is underbody body coating? Well its a process in which the basement of the car is painted to protect it from dirt and rust.Since the basement of the car is exposed to muddy water, stones, potholes.  2.Process- First the underbody of the car is washed & degreased & afterthat the layers of the paint…

As Mr  Pughazhyendhii is fond of big cars that means it may be either sedan or any suv. Now he is having a total budget of Rs 8-10 Lac. As he has to travel 500km/month plus office let say he\'s office is located at a distance of 5km from home so total distance for office in a day = 10 km/day..that turns out to be…