Back-Flow Tutorial

                                                                                1. PORT FUEL INJECTION Previously the only…

                                                                                           …

                                                       Port Flow Injection of SI EngineThe PFI estimates the simulates the full working of an SI-Engine. By definition in an SI-Engine…

                                                       Port Flow Injection of SI EngineThe PFI estimates the simulates the full working of an SI-Engine. By definition in an SI-Engine…

 *********** Comments by Grader ************GOOD JOB !!!!SUGGESTION : The other thing that you can do is to attach the code and images in projects.skill-lync.com  and paste the link over here.If you have any…

I have finished the case setup tutorial for the varied grid sizes of 1mm, 1.5mm and 2mm. The order of magnitude of 0.1mm is not feesible in my laptop. I have uploaded image in the order of brid images, pressure, velocity and temp. for grid sizes 1mm, 1.5mm and 2mm .                

I have finished the case setup tutorial for the varied grid sizes of 1mm, 1.5mm and 2mm. The order of magnitude of 0.1mm is not feesible in my laptop. I have uploaded image in the order of brid images, pressure, velocity and temp. for grid sizes 1mm, 1.5mm and 2mm .                

                                                                                    Reynolds Averaging The Reynolds…

                                                       Port Flow Injection of SI Engine The PFI estimates the simulates the full working of an SI-Engine. By definition in an SI-Engine…

                                                       Port Flow Injection of SI Engine The PFI estimates the simulates the full working of an SI-Engine. By definition in an SI-Engine…

Conjugate Heat Transfer Simulation-Super Cycling Objective:- Here we simulate the conjugate heat transfer problem for a cylindrical interface of length 0.2M & dia. 0.015M. The super-cycling was incorporated and varied time scales of 0.01sec, 0.02 sec & 0.03 sec. Results:- There were two regions set as solid &…

Shock Tube-Transient Objective:- The shock tube problem for transient conditions with pressures 6 bar & 1 bar at high pressure & low-pressure region is simulated at transient state. The shock tube is used to study the chemical kinematics of fuels especially n-heptane, naphtha, propane etc. Due to the high-pressure…

Throttle Problem-Transient Objective:- To simulate the Throttle Problem at Transient state. The throttle opens up by an angle of 20 degrees.   Problem:- Steady State The throttle problem was first simulated in steady state. The plots for pressure, temperature and velocity were obtained. Density Temperature Pressure…

This project is the essence of my MS Thesis at West Virginia University. We did an extensive study in the simulation of large-scale combustion problem.                                                …

I had finished the BF-tutorial with grid sizes 1mm, 1.5mm and 2mm. Have post processed  and as the previous challenge , have ordered it as grid size images, pressure, temp. and velocity post processed images.                               …

Prantle Mayer Shock :- Under conditions of compressible and inviscid flow with Mach Number greater than 1 , gas flowing through a sharp edge with convex corner has infinite number of expansion waves. Inside this fan of waves comes physical properties like total pressure, total temperature remain constant whereas Mach Number,…

I had finished the BF-tutorial with grid sizes 1mm, 1.5mm and 2mm. Have post processed  and as the previous challenge , have ordered it as grid size images, pressure, temp. and velocity post processed images.                               …

I had finished the BF-tutorial with grid sizes 1mm, 1.5mm and 2mm. Have post processed  and as the previous challenge , have ordered it as grid size images, pressure, temp. and velocity post processed images.                               …

I have finished the case setup tutorial for the varied grid sizes of 1mm, 1.5mm and 2mm. The order of magnitude of 0.1mm is not feesible in my laptop.  I have uploaded image in the order of brid images, pressure, velocity and temp. for grid sizes 1mm, 1.5mm and 2mm .              …

I have finished the case setup tutorial for the varied grid sizes of 1mm, 1.5mm and 2mm. The order of magnitude of 0.1mm is not feesible in my laptop.  I have uploaded image in the order of brid images, pressure, velocity and temp. for grid sizes 1mm, 1.5mm and 2mm .              …

I have finished the case setup tutorial for the varied grid sizes of 1mm, 1.5mm and 2mm. The order of magnitude of 0.1mm is not feesible in my laptop.  I have uploaded image in the order of brid images, pressure, velocity and temp. for grid sizes 1mm, 1.5mm and 2mm .              …

I have finished the case setup tutorial for the varied grid sizes of 1mm, 1.5mm and 2mm. The order of magnitude of 0.1mm is not feesible in my laptop.  I have uploaded image in the order of brid images, pressure, velocity and temp. for grid sizes 1mm, 1.5mm and 2mm .              …

I had tried the back flow tutorial for varied grid sizes as prescribed, in the challenge. I am attaching the images and the smulation results