Port Flow Injection of SI Engine The PFI estimates the simulates the full working of an SI-Engine. By definition in an SI-Engine…

I had finished the BF-tutorial with grid sizes 1mm, 1.5mm and 2mm. Have post processed  and as the previous challenge , have ordered it as grid size images, pressure, temp. and velocity post processed images.                               …

I have finished the case setup tutorial for the varied grid sizes of 1mm, 1.5mm and 2mm. The order of magnitude of 0.1mm is not feesible in my laptop.  I have uploaded image in the order of brid images, pressure, velocity and temp. for grid sizes 1mm, 1.5mm and 2mm .              …

Shock Tube-Transient Objective:- The shock tube problem for transient conditions with pressures 6 bar & 1 bar at high pressure & low-pressure region is simulated at transient state. The shock tube is used to study the chemical kinematics of fuels especially n-heptane, naphtha, propane etc. Due to the high-pressure…

I have finished the case setup tutorial for the varied grid sizes of 1mm, 1.5mm and 2mm. The order of magnitude of 0.1mm is not feesible in my laptop. I have uploaded image in the order of brid images, pressure, velocity and temp. for grid sizes 1mm, 1.5mm and 2mm .                

I have finished the case setup tutorial for the varied grid sizes of 1mm, 1.5mm and 2mm. The order of magnitude of 0.1mm is not feesible in my laptop. I have uploaded image in the order of brid images, pressure, velocity and temp. for grid sizes 1mm, 1.5mm and 2mm .                

I had tried the back flow tutorial for varied grid sizes as prescribed, in the challenge. I am attaching the images and the smulation results      

Throttle Problem-Transient Objective:- To simulate the Throttle Problem at Transient state. The throttle opens up by an angle of 20 degrees.   Problem:- Steady State The throttle problem was first simulated in steady state. The plots for pressure, temperature and velocity were obtained. Density Temperature Pressure…

I had finished the BF-tutorial with grid sizes 1mm, 1.5mm and 2mm. Have post processed  and as the previous challenge , have ordered it as grid size images, pressure, temp. and velocity post processed images.                               …

I have finished the case setup tutorial for the varied grid sizes of 1mm, 1.5mm and 2mm. The order of magnitude of 0.1mm is not feesible in my laptop.  I have uploaded image in the order of brid images, pressure, velocity and temp. for grid sizes 1mm, 1.5mm and 2mm .              …

                                                                                1. PORT FUEL INJECTION Previously the only…

                                                       Port Flow Injection of SI EngineThe PFI estimates the simulates the full working of an SI-Engine. By definition in an SI-Engine…

Prantle Mayer Shock :- Under conditions of compressible and inviscid flow with Mach Number greater than 1 , gas flowing through a sharp edge with convex corner has infinite number of expansion waves. Inside this fan of waves comes physical properties like total pressure, total temperature remain constant whereas Mach Number,…

I have finished the case setup tutorial for the varied grid sizes of 1mm, 1.5mm and 2mm. The order of magnitude of 0.1mm is not feesible in my laptop.  I have uploaded image in the order of brid images, pressure, velocity and temp. for grid sizes 1mm, 1.5mm and 2mm .              …

                                                       Port Flow Injection of SI EngineThe PFI estimates the simulates the full working of an SI-Engine. By definition in an SI-Engine…

I had finished the BF-tutorial with grid sizes 1mm, 1.5mm and 2mm. Have post processed  and as the previous challenge , have ordered it as grid size images, pressure, temp. and velocity post processed images.                               …

                                                                                           …

I have finished the case setup tutorial for the varied grid sizes of 1mm, 1.5mm and 2mm. The order of magnitude of 0.1mm is not feesible in my laptop.  I have uploaded image in the order of brid images, pressure, velocity and temp. for grid sizes 1mm, 1.5mm and 2mm .              …

This project is the essence of my MS Thesis at West Virginia University. We did an extensive study in the simulation of large-scale combustion problem.                                                …

Conjugate Heat Transfer Simulation-Super Cycling Objective:- Here we simulate the conjugate heat transfer problem for a cylindrical interface of length 0.2M & dia. 0.015M. The super-cycling was incorporated and varied time scales of 0.01sec, 0.02 sec & 0.03 sec. Results:- There were two regions set as solid &…

                                                                                    Reynolds Averaging The Reynolds…

 *********** Comments by Grader ************GOOD JOB !!!!SUGGESTION : The other thing that you can do is to attach the code and images in projects.skill-lync.com  and paste the link over here.If you have any…

                                                       Port Flow Injection of SI Engine The PFI estimates the simulates the full working of an SI-Engine. By definition in an SI-Engine…