3D Creation of Celing, Roof, Architectural plan, Structural plan, Sectional view, Elevation view and Camera specific view for a house plan using REVIT
ANSWER NO 1
AIM - Model a Ceiling from the architecture tab above the walls at the first-floor level.
PROCEDURE
STEP 1 INSERT THE CHALLANGE WEEK 3 LAYOUT
STEP 2 LEVEL 2 CONVERT INTO FIRST FLOOR
STEP 3 GO TO THE ARCHITECTURAL TEMPLATES AND SELECT CEILING OPTION.
STEP 4 GO TO THE CEILING OPTION THEN SELECT SKETCH CEILING.
STEP 5 AFTER THE SELECT SKETCH CEILING THEN WE ARE SELECT PICK LINE OPTION FOR CELING .
RESULT
ANSWER NO 2
AIM Create a roof above the ceiling by selecting the footprints of the ceiling and adjust the roof slope to 10 degrees.
PROCEDURE
STEP 1 GO TO THE ARCHITECTURAL TAB SELECT ROOF OPTION THEN SELECT ROOF BY FOOTPRINTS.
STEP 2 SELECT THE PICK LINES FOR CREATING ROOF.
STEP 3 ADJUST THE ROOF SLOPE 10 DEGREE.
RESULT
ANSWER NO 3
AIM - Create plan views for ground floor level and first-floor level including all the walls, floors, and components. Separate them to architecture and structural plans.
PROCEDUARE
STEP 1 GO TO THE VIEW OPTION AND SELECT PLAN VIEW
STEP 2 SELECT ARCHITECTURAL PLAN OR FLOOR PLAN.
STEP 4 SELECT THE STRUCTURAL PLAN .
STEP 5 SELECT THE STRUCTURAL PLAN FOR GROUND FLOOR
STEP 6 SELLECT THE STRUCTURAL PLAN FOR FIRST FLOOR
STEP 7 SELECT THE DIMENSIONS FOR USING ALIGNED ROM ANNOTE TOOLBAR
STEP 8 RESULT OF DIMENSIONS OF ARCHITECTURAL PLAN
STEP 9 SELECT THE ANNNOTE TAB FOR CREATING DIMENSIONS FOR STRUCTURAL PLAN BY USING ALIGNED
STEP 10 RESULT THE DIMENSIONS OF STRUCTURAL PLAN
ANSWER NO 4
AIM Create a sheet template from the view tab and adjust the parameters on the sheet to add appropriate views
PROCEDURE
STEP 1 GO TO THE VIEW TOOLBAR AND SELECT THE SHEET OPTION
RESULT
STEP 2 ADD THE GROUND FLOOR ON THE SHEET AS A VIEW
ANSWER N0 6
AIM Using the elevation tab create the elevation views, looking at your building from East, North, South, and West
PROCEDURE
STEP 1 GO TO THE VIEW OPTION AND SELECT THE ELEVATION VIEW
STEP 2 SELLECT THE ELEVATION FOR EAST,WEST,NORTH & SOUTH .
RESULT OF EAST ELEVATION VIEW
RESULT ELEVATION VIEW OF WEST
RESULT THE ELEVATION VIEW OF NORTH
RESULT THE ELEVATION VIEW OF SOUTH
ANSWER NO 7
AIM Produce section cut through each room either cutting across longitudinally or in a transverse direction
PROCEDURE
STEP 1 GO TO THE VIEW TOOLBAR AND SELECT THE SECTION VIEW
STEP 2 CUT THE BED ROOM 1 IN LONGITUDNAL AND BED ROOM 2 CUT BY TRANSVERSE SND HALL ALSO CUT IN TANSVERSE DIRECTION.
RESULT THE LONGITUDNAL SECTION CUT
RESULT THE TRANSVERSE SECTION CUT VIEW
ANSWER NO 8
AIM Classify the views, Plan Views, Section Views, and Elevation views
PROCEDURE
STEP 1 GO TO THE PROPERTIES OPTION AND SELECT THEALL VIEWS
RESULT OF FLOOR VIEW AND ELEVATION VIEW
RESULT THE SECTION VIEWS
ANSWER NO 9
AIM Using the sheet template produced create multiple sheets as follows
a. A 101- Ground Floor Architecture Plan
b. A 102- First Floor Architecture Plan
c. A 103- Roof Plan
d. S 101- Ground Floor Structural Plan
e. S 102- First Floor Structural Plan
f. S 103- Roof Framing Plan
g. A-201- North-South Elevations
h. A-202- East-West Elevations
PROCEDURE
STEP 1 GP TO THE VIEW TOOLBAR AND SELECT THE SHEET VIEW
STEP 2 A 101- Ground Floor Architecture Plan
STEP 3 A 102- FIRST Floor Architecture Plan
STEP 4 - A 103- Roof Plan
STEP 5- S 101- Ground Floor Structural Plan
STEP 6- S 102- FIRST Floor Structural Plan
STEP 7 S 103- Roof Framing Plan
STEP 8 A-201- North-South Elevations
STEP 9 A-202- East-West Elevations
ANSWER NO 10
AIM Create a camera-specific view or a 3D view in each room ( living, dining, bedroom). AND THE THEASE VIEW ATTACH ON THE SHEET
PROCEDURE
STEP 1 GO TO THE VIEW TOOLBAR THEN SELECT THE CAMERA FROM 3D VIEW OPTION
STEP 2 ATTACH THE 3D VIEW OF LIVING ROOM ON THE SHEET
STEP 3 ATTACH THE 3D VIEW OF DINNING ROOM ON THE SHEET
STEP 4 ATTACH THE 3D VIEW OF BED ROOM ON THE SHEET