3D Creation of Ceiling, Roof, Architectural plan, Structural plan, Sectional view, Elevation view and Camera specific view for a house plan using REVIT
1.Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level
AIM
To model a Ceiling from the architecture tab above the walls at the first-floor level
PROCEDURE:
- From the architectural tab, ceiling tab is used to create the ceiling at the top floor
RRSULT:
Given answer attached to the choose file dialouge box
2.Model a roof above the ceiling by selecting the footprints of the ceiling. Using the adjustment toolbars appearing on-screen adjust the roof slope to 10 degrees
AIM:
To model a roof above the ceiling by selecting the footprints of the ceiling
PROCEDURE:
- In the architectural tab, create roof tab is selected to create the roof
- The boundary is selected to create the roof and the slope is changed to 10 degrees in the properties as shown below.
RESULT:
Given answer attached to the choose file dialouge box
3.Using the file saved from weeks 2 to 4, create plan views for ground floor level and first-floor level including all the walls, floors, and components. Separate them to
architecture and structural plans
a. Architecture plan must have walls, floors, and all the components placed within the building
b. Structure plan must have details of only walls, floors, and columns
AIM:
To create architectural and structural plan views.
PROCEDURE:
- The created model, plan view shows the architctural plan view as shwon
- From the view tab, the structural plan view can be created from plan drop
RESULT:
Given answer attached to the choose file dialouge box
4.Using annotate toolbar add dimensions to all the walls and floors with reference to the longitudinal and transverse grids created in the project file
a. The architecture plan dimensions include details on where the components are placed within the buildings with relation to grids. Overall dimensions are sufficient for architecture plans
AIM:
To create grids for architectural and structural plan views
PROCEDURE:
- From the architectural tab, the grids are created in horizontal and vertical directions and the distances are annotated.
RESULT:
Given answer attached to the choose file dialouge box
5.Create a sheet template from the view tab and adjust the parameters on the sheet to add appropriate views
AIM :
To create sheet templates.
PROCEDURE:
- Fron the view tab, click on sheets to create the sheets.
- The changes are made to the sheet
RESULT:
Given answer attached to the choose file dialouge box
6.Using the elevation tab create the elevation views, looking at your building from East, North, South, and West
AIM:
To create elevation views
PROCEDURE:
- From the view tab, North, South, East and West elevations are created
RESULT:
Given answer attached to the choose file dialouge box
7.Produce section cut through each room either cutting across longitudinally or in a transverse direction
AIM:
To create section cut through each room.
PROCEDURE:
- From view tab, sections are created such that all the rooms in that section are visible.
- Three different sections are created trying to cover all the rooms of the buildin
RESULT:
Given answer attached to the choose file dialouge box
8.Classify the views, Plan Views, Section Views, and Elevation views to either Design or Documentation category using Properties browser
AIM:
To create a section view paln view
PROCEDURE:
- From view tab, sections are created such that all the rooms in that section are visible.
- Three different sections are created trying to cover all the rooms of the building
REDULT:
Given answer attached to the choose file dialouge box
9.Using the sheet template produced create multiple sheets as follows
a. A 101- Ground Floor Architecture Plan
b. A 102- First Floor Architecture Plan
c. A 103- Roof Plan
d. S 101- Ground Floor Structural Plan
e. S 102- First Floor Structural Plan
f. S 103- Roof Framing Plan
g. A-201- North-South Elevations
h. A-202- East-West Elevations
AIM:
To create sheet templates
PROCEDURE :
- Various sheets having various elements of the building
RESULT:
Given answer attached to the choose file dialouge box
10.Create a camera-specific view or a 3D view in each room ( living, dining, bedroom). Based on the views create a new set of sheets starting A-501 (you can add as many sheets after, 502, 503.. n)to place the 3D view images. Produce the sheets
AIM :
To create camera specific views
PROCEDURE:
- Various sheets containing camera views of all the rooms are created
RESULT :
Given answer attached to the choose file dialouge box