Executive Programs

Workshops

Projects

Blogs

Careers

Student Reviews

More

Informative Articles

Find Jobs

We are Hiring!

All Courses

Choose a category

All Courses

All Courses

Aashish Sharma

Works in the area of renewable energy

Skills Acquired at Skill-Lync :

• CFD
• ANSYS-FLUENT

Introduction

.

9 Projects

Cyclone separator challenge

Objective:

Introduction: The four models used for cyclone separator are: Iozia and Leith model: This model assumes that a particle carried by the vortex endures the influence of two forces; centrifugal and flow resistance. It considers simple force balance on the particle in the cyclone. It assumes that centrifugal force and drag…

28 Nov 2019 04:50 AM IST

Conjugate Heat Transfer analysis of an exhaust port

Objective:

1. Conjugate Heat Transfer: Conjugate heat transfer corresponds with the combination of heat transfer in solids and heat transfer in fluids. In solids, conduction often dominates whereas, in fluids, convection usually dominates. Conjugate heat transfer is observed in many situations. For example, heat sinks are optimized…

21 Sep 2019 04:54 AM IST

• HVAC

Objective:

Comment: ============================== The Strouhal number must be appx 0.16 for a flow over cylinder with renoylds number of 100. As it is not matching i deduct marks. ================================== Problem Statement: To simulate the steady and transient model for flow over a cylinder (Re=100) Input parameters: inlet…

30 Oct 2019 01:03 PM IST

Combustion analysis using Eddy dissipation turbulence model

Objective:

Aim: To perform a combustion simulation on the combustor model and to plot the mass fraction of different species at the different locations inside a combustor. Combustion: combustion is a high-temperature exothermic redox chemical reaction between fuel and air (primarily with oxygen) that produces a gaseous product as…

18 Mar 2020 05:36 AM IST

The Ahmed Body grid independence test and basic analysis

Objective:

1. Ahmed Body and its importance: The Amed Body was first described by S.R. Ahmed in 1984. Its layout is as follows: Three main features were seen in the wake: 1. The A recirculation region that is formed as the flow separates at the top of the vertical back surface of the model. 2. The B recirculation region is formed…

07 Oct 2019 02:50 AM IST

Gate Valve Parametric Analysis

Objective:

Introduction: A gate valve, also called sluice valve, is a valve used to isolate the flow in pipeline. They are controlled either by clockwise rotation to close (CTC) or clockwise to open (CTO) rotating stem. When operating the valve the gate moves up and down on the threaded stem. It is preferred as it does not restrict…

27 Nov 2019 11:50 AM IST

Mixing flow T-Joint

Objective:

Challenge-1 A comparative steady-state analysis of a mixing T pipe (as shown in fig 1) is done. Fig.1: T joint with hot and cold fluid (mixing) flow.   Three cases are analyzed as per the description below: Case-1: Short length pipe with hot inlet air (x-axis) inlet velocity of 3m/s and cold air (y-axis) inlet velocity…

30 Oct 2019 01:01 PM IST

Rayleigh Taylor Instability Model

Objective:

Introduction: Rayleigh Taylor instability is observed at the interface of two different density fluids interacting with each other. This mixing example can be water suspended over air under the effect of gravity., where the air will penetrate the water forming bubbles and instability is observed. Some Practical CFD models…

04 Nov 2019 10:45 AM IST

Conjugate Heat Transfer Analysis on a graphics card.

Objective:

Aim: To perform conjugate heat transfer analysis on a graphic card Objectives: Run the simulation by varying the velocity from 1m/sec to 5m/sec for at least 3 velocities and discuss the results. Find out the maximum temperature and heat transfer coefficient attained by the processor. Prove that the simulation has achieved…

29 Jun 2020 10:04 AM IST

Showing 1 of 9 projects

1 Course Certificates

Introduction to GUI based CFD using ANSYS Fluent

Certificate UID: 5g6pn8oulme4bj7d
Showing 1 of 1 certificates

4 Workshop Certificates

CFD Preprocessing using ANSA

Certificate UID: 4rn7qt21gh

Basics of electric vehicle simulations using Ansys

Certificate UID: 2krzv98sd5

Design optimization using Finite element analysis - FEA

Certificate UID: xnyg2cr9e1

Numerical Methods for Solving Differential Equations

Certificate UID: 9yicsqf7zv
Showing 1 of 4 certificates

10th

St. Marys High School

28 Aug 2022 - 06 Sep 2022

12th

MLSM college

30 Aug 2021 - 06 Sep 2022

Ph.D

Lovely Professional University

28 Aug 2022 - 06 Sep 2022

Schedule a counselling session

Here are the courses that I have enrolled

4.7

16 Hours of Content

Similar Profiles

Apoorv Ranjan

Ladder of success cannot be climbed with hands in pocket.