Aim :-  To Write a program in Matlab that will simulate the pendulum motion   Objective :- First objective is to write a program that solves the 2 order ODE To Write a program in Matlab that will simulate the pendulum motion To plot the graph of displacement and velocity v/s time and animate the motion of bob.…

   AIM :- To write the commands to create a row and column vector in Matlab.   Theory :- Using matlab we can create a simple row and column vector To create a simple row vector we use a square bracket as [ ] or say Array, and placing the numbers in the square bracket. Eg :- [ 10 , 20 , 30 ] creates…

# Attempt 1 You scored 50/50 in this challenge. Please see the below table for details Requirement Explanation Maximum Marks Marks Obtained Code Code should be attached with comments 20 20 Outputs Output plots/videos must be attached 10 10 Explanation Code and outputs must be explained 20 20 Grading Comments:…

Aim :-  Write a function that extracts the 14 co-efficients and calculates the enthalpy, entropy and specific heats for all the species in the data file.   Objective :-  Write a function that extracts the 14 coefficients and calculates the enthalpy, entropy and specific heats for all the species in the data…

# Attempt 1 You scored 50/50 in this challenge. Please see the below table for details Requirement Explanation Maximum Marks Marks Obtained Code Code should be attached with comments 20 20 Outputs Output plots/videos must be attached with proper plot labels and title 10 10 Explanation Code and outputs must be…

Aim :- Using the following 2D CAD drawings to create the 3D model of the internal Geneva mechanism.   Objective :-  Create 3D models for driver and driven wheels. Perform motion analysis by rotating the driver wheel at 10rpm.& 20 rpm Obtain the following plots for Contact force (between driving and the driven wheel) as…

Aim :- Motion analysis of the planetary gear , To Design the Planetary Gear & to run a simulation for it.   Objective :- for the following inputs provided designing the Planetary Gear for the input parameters , run a simulation on the following cases calculate the pitch circle diameter and the number…

Aim :- To model all the parts of the piston assembly and then to assemble them in SolidWorks & to obtain motion analysis of it   Objective :-  To model all the parts and then assemble them in SolidWorks To run the motion analysis for three different conditions,   0 mm  wrist pin Offset ,10…

Aim :- To model the parts for IC Engine Valve Train and to assemble them in solidworks and obtain the mbd simulation for it   Objective :-  To model the parts for IC Engine Valve Train  To assemble all the parts and to run the motion analysis for it  To Obtain the simulation for the two diffrent…

Aim :- To run an internal pipe flow simulation in solidworks and to plot the velocity profile.   Objective :-  Run a pipe flow simulation with an inlet Reynolds number of 100,1000 and 10,000 Place line probes at 95%, 90% and 85% of the pipe length & Compare the normalized velocity profile at each of…

Aim :- To simulate the flow over a cylinder in solidworks   Objective :- To simulate the flow over a cylinder for the conditions shown in the video To Run a baseline simulation and then calculate the Reynolds number. Then increase the Reynolds number by a factor of 20%, 40%, and 100% then run the transient flow simulation.…

Aim :- To model the flow over a NACA0017 airfoil for the given angle of attacks and to compare the lift and drag forces   Objective :-  To model the flow over a NACA0017 airfoil for the angle of attacks 0,2,4,6,8,10,etc. To compare the lift and drag force for each case      Theory :-  An airfoil…

Aim :- To create a 3D model of a flow bench and run flow analysis & to obtain the plot for lift vs mass flow rate.   Objective :-  create a 3D model of a flow bench and run flow analysis. To obtain the plot for lift vs mass flow rate. Run the grid dependence test, For three grids run the simulation at a particular…

 Aim :- To design a centrifugal pump and analyse the flow through it & Obtain the relationship between Pressure ratio and mass flow rate    Objective :-  To design a centrifugal pump and analyse the flow through it To obtain the relationship between Pressure ratio and mass flow rate   …

Aim :- To design the Rectangular,I-section & C-section beams and for a particular load value analyse the bending/deflection in the beam    Objective :- To model three types of beam ( Rectangular beam , I-section beam & C-section beam ) For the load value of 1500N analyse the deflection/bending for the…

Aim :-  To perform a buckling analysis on a cyclonic separator stand    Objective :- To perform a buckling analysis on a cyclonic separator stand  To create a metallic stiffener on the legs of the stand and run the analysis to find out the change in buckling factor of safety.  To run a design…

Aim :- To perform a static analysis on two models of plate with holes   Objective :-  To perform a static analysis on two models of plate with holes (plate with single hole and a plate with three holes ) To apply a fixed relation to one of the short side of the plate and apply a force of 1000N on the other such…

Aim :- To Create a model of a rotating shaft and to perform a frequency analysis on it.   Objective :- To create the model in Solidworks according to dimensions that you see fit  Then Conduct the frequency analysis by applying a bearing fixture on the stepped face of the rod at the two ends  Find out…