Full course · free on YouTube · 2 h 0 min

Vehicle diagnostics with CAN and UDS: free, 2 hours

One webinar recording of about 2 hours, narrated over slides and ending with a live demo, from April 2023. It moves from ECUs and the CAN network to CAN-TP and UDS services, then security access, timing, the bootloader, AUTOSAR and a diagnostic request on real hardware.

24 chapters · published 18 Apr 2023 · 12,282 views as of 19 Nov 2026 · by Skill-Lync

Free. We ask for your name and phone once before it plays here · or watch on YouTube ↗

Who is this course for?

Electrical, electronics and embedded engineering students and engineers who want to understand how a car's ECUs are diagnosed and reprogrammed over CAN.

What will you learn?

  • Explain what an ECU is and how ECUs share a CAN bus
  • Tell on-board and off-board diagnostics apart, and say where UDS sits above CAN-TP
  • Describe how CAN-TP uses single, first, consecutive and flow control frames to send more than eight bytes
  • Read a UDS request and response: service ID plus 0x40 for a positive reply, 0x7F for a negative one
  • Use the services shown for sessions, reset, tester present, read and write data, clearing and reading DTCs, and routine control
  • Describe the seed and key exchange, the S3, P2 and P2 star timings, and the bootloader flashing sequence

What does each part of the course cover?

10 sections, in watching order. Click a timestamp to jump the player there. The video description has no chapter list, so these chapters and timestamps were written from the video itself.

  1. 0:0010 min · 2 chapters

    ECUs in the car and the CAN network

    The agenda, then what an ECU is: the 'brain' of a car function, with a car carrying many of them grouped by job (essential, comfort, security, active and passive safety). Each ECU is a microcontroller running flashed firmware, joined to the others on a CAN bus with 120 ohm terminations.

    Chapters
    • 0:00Agenda and the ECUs in a vehicle
    • 4:08ECU history and categories, inside an ECU, and why CAN
  2. 9:5910 min · 3 chapters

    Diagnostics, the CAN frame and the diagnostic stack

    On-board versus off-board diagnostics, with diagnostics carried over CAN (DoCAN) and UDS as the off-board language. Then the CAN frame, reduced to the 11-bit identifier and the data field, why CAN is not address based, and the layers from CAN driver up to UDS.

    Chapters
    • 9:59On-board and off-board diagnostics, DoCAN and UDS
    • 15:21The CAN frame: identifier and data field
    • 18:53The diagnostic software stack
  3. 20:1111 min · 3 chapters

    CAN-TP: sending more than eight bytes

    Why plain CAN's eight-byte data field is not enough and how the CAN transport protocol segments longer messages, up to about 4 kilobytes. The single, first, consecutive and flow control frames are explained, including the protocol byte, sequence numbers, block size and the time between frames.

    Chapters
    • 20:11Why CAN-TP is needed
    • 22:58CAN-TP frame types and the single frame
    • 24:28First, consecutive and flow control frames
  4. 31:1215 min · 4 chapters

    Data identifiers, DTCs, routine identifiers and UDS basics

    The three kinds of identifier UDS works with: data identifiers (for example the vehicle identification number), diagnostic trouble codes as five-character codes, and routine identifiers such as running a cooling fan or erasing memory. Then UDS as request-response, the service groups, and positive and negative responses.

    Chapters
    • 31:12Data identifiers (DIDs)
    • 33:25Diagnostic trouble codes (DTCs)
    • 36:15Routine identifiers
    • 37:56UDS overview, service groups, positive and negative responses
  5. 46:2717 min · 3 chapters

    Sessions, reset, communication control and tester present

    Diagnostic session control (default, programming and extended sessions, with the five-second timeout back to default), ECU reset types, communication control for enabling or disabling an ECU's reception and transmission, tester present to keep a session alive, and control of DTC setting.

    Chapters
    • 46:27Diagnostic session control
    • 51:07ECU reset and communication control
    • 59:06Tester present and control DTC setting
  6. 1:03:2914 min · 3 chapters

    Reading, writing and clearing data and DTCs; routines

    Read data by identifier and write data by identifier with their positive responses, then clearing DTCs for all or a group, how an over-voltage or under-voltage event gets stored, and reading DTCs with a status mask. Ends with routine control: start, stop and request results.

    Chapters
    • 1:03:29Read and write data by identifier
    • 1:06:52Clearing DTCs, DTC events and the status mask
    • 1:14:37Routine control
  7. 1:17:5817 min · 2 chapters

    Security access and timing parameters

    Locking and unlocking an ECU with the security access service: the tester requests a seed, calculates a key, and the ECU compares it with its own. Then the timing parameters: the S3 timeout of 5000 ms, P2 of 50 ms and P2 star of 5000 ms with the response-pending negative response.

    Chapters
    • 1:17:58Security access: seed and key
    • 1:28:36Timing parameters: S3, P2 and P2 star
  8. 1:34:448 min · 1 chapter

    Bootloader and ECU flashing over CAN

    Why ECUs are reprogrammed in the car through the OBD connector rather than removed. The flash is split into a bootloader area and an application area, and the sequence runs through programming session, boot flag, erase, request download, transfer data, transfer exit and a checksum.

    Chapters
  9. 1:42:2713 min · 2 chapters

    AUTOSAR and the diagnostic stack

    AUTOSAR as a standard middleware so the same application can move between microcontrollers, with the application, runtime environment and basic software layers. Then how diagnostics map onto it: monitoring components, the event manager storing faults in NVM, and CAN-TP feeding the diagnostic communication manager.

    Chapters
    • 1:42:27AUTOSAR and why it is used
    • 1:52:16Diagnostics in the AUTOSAR stack
  10. 1:55:095 min · 1 chapter

    Live demo: reading data identifiers

    A PC connected to an ECU through a CAN interface at 500 kbit/s. Read data by identifier gets positive responses, an identifier that is not stored gets a negative response with request out of range, and a request with a one-byte identifier gets incorrect message length.

    Chapters
    • 1:55:09Demo: reading data identifiers over CAN

Is the Know How Your Vehicle Diagnostics Works course really free?

Yes. All 2 h 0 min of it is free on Skill-Lync's YouTube channel, with no payment. To watch it on this page with the chapter guide, leave your name and phone number once; you can also watch it directly on YouTube. It was published on 18 Apr 2023 and had 12,282 views as of 19 Nov 2026. This page adds the chapter guide, a study plan and what to learn next.

How long does the Know How Your Vehicle Diagnostics Works course take to finish?

The video runs 2 h 0 min across 24 chapters. At one hour a day that is about 2 days; plan roughly twice that if you practise each exercise as you go. The longest section is "Sessions, reset, communication control and tester present" (17 min), so give it its own days.

Does the free vehicle diagnostics course come with a certificate?

The video description has a "claim your certificate" link, which now opens this page. To ask about a certificate for this course, leave your name and phone number in the form below and a Skill-Lync counsellor will call you back. The paid Skill-Lync courses linked here include a certificate along with mentor-reviewed projects.

What should I learn after this course?

The next step is Fundamentals of Electrical Systems and Electrical Architecture (free lessons), then Introduction to Automotive Embedded Systems and AUTOSAR (₹40,000), then Pre-Graduate Program in Embedded Systems (₹1,50,000). The free course teaches the concepts; the paid Skill-Lync courses add graded projects, mentor feedback and, in the PG programs, placement support.

What does the live demo in the diagnostics webinar show?

A PC sends read data by identifier requests (service 0x22) to an ECU through a CAN interface on a 500 kbit/s bus. Two stored identifiers come back positive (0x62, the service ID plus 0x40, then the data). An identifier the ECU does not hold returns 0x7F with NRC 0x31, request out of range, and a request with a one-byte identifier returns NRC 0x13, incorrect message length.

Do I need to know CAN or UDS before watching?

No prerequisite is stated. The talk starts with what an ECU is and how CAN connects ECUs, then builds up to UDS. Basic ideas such as microcontrollers and firmware are explained in passing. It helps to know what a microcontroller is, but the video does not require it.

Which UDS services does the webinar cover?

It covers diagnostic session control, ECU reset, communication control, tester present, control DTC setting, read and write data by identifier, clear and read DTCs, routine control and security access. The speaker says some services are skipped for time. It also touches on request download, transfer data and transfer exit for flashing.

Last updated 19 Nov 2026 · Course length, chapters, views and dates from the YouTube video on 19 Nov 2026 · Grow by Skill-Lync: free lessons from every course

Finished the course?

Ask about the certificate or your next course.

Leave your name and phone number. A Skill-Lync counsellor calls you back within one working day about the certificate for Know How Your Vehicle Diagnostics Works and the course that fits where you want to work.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Free full course · Skill-Lync

Start watching

Free, no payment. Leave your name and phone once and the whole Know How Your Vehicle Diagnostics Works course plays here, with every free lesson on Grow. A Skill-Lync counsellor may call you about the certificate or your next course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.