Full course · free on YouTube · 4 h 48 min

Strength of materials full course: free, 4.8 hours

One lecture video of about 4 hours 48 minutes in four chapters of three or four sessions each: stress and strain, stress transformation and Mohr's circle, beams and shafts, then theories of failure. Each session mixes slides, derivations on a whiteboard and worked numerical examples.

14 chapters · published 8 Nov 2024 · 74,271 views as of 18 Nov 2026 · by Skill-Lync

Free. We ask for your name and phone once before it plays here · or watch on YouTube ↗

Who is this course for?

Mechanical and civil engineering students, and anyone starting structural or mechanical analysis, who want the basics of stress, beams, shafts and failure criteria in one video.

What will you learn?

  • Define strength, stiffness, toughness and hardness, and tell engineering stress and strain from true stress and strain
  • Work out stress, strain and Young's modulus from load-elongation test data, and use Poisson's ratio to find lateral strains
  • Transform plane stress to a rotated plane, then find principal stresses and maximum in-plane shear stress with equations and with Mohr's circle
  • Identify beam supports and loads, and draw shear force and bending moment diagrams for simply supported and cantilever beams
  • Use the bending equation, section modulus and double integration for deflection, and the torsion formula for solid and hollow circular shafts
  • Compare the Tresca and distortion energy theories for ductile materials with the Rankine and Mohr criteria for brittle ones

What does each part of the course cover?

8 sections, in watching order. Click a timestamp to jump the player there. The video description only numbers its chapters, so the chapter titles here say what each one teaches, written from the video.

  1. 2:2531 min · 2 chapters

    Stress, strain and the stress-strain diagram

    Defines the strength of a material and the mechanical (strength, stiffness, toughness, hardness) and geometrical properties that affect it. Covers normal, shear and torsional stress, engineering versus true stress and strain, Hooke's load-extension stiffness, and the stress-strain diagram with its elastic and plastic regions and Young's modulus.

    Chapters
    • 2:25Strength of a material, its properties and simple stresses (chapter 1, session 1)
    • 11:21Simple strains, stiffness and the stress-strain diagram (chapter 1, session 2)
  2. 33:2031 min · 2 chapters

    Young's modulus from test data and Poisson's ratio

    Calculates stress, strain and Young's modulus from load-elongation test data and reads the limiting, yield, ultimate and fracture stresses off the plot. Then solves a rigid bar held by an aluminium member, and introduces Poisson's ratio with a rectangular bar and an aluminium bar example giving strains and elongations in x, y and z.

    Chapters
    • 33:20Young's modulus from test data and a rigid-bar example (chapter 1, session 3)
    • 49:04Poisson's ratio with rectangular and aluminium bar examples (chapter 1, session 4)
  3. 1:04:1228 min · 1 chapter

    Plane stress transformation equations

    Introduces the 2D stress element and the sign convention, then derives the normal and shear stress on a plane rotated by an angle theta from a force balance on a triangular element and trigonometric identities. Ends with a worked example on a rotated element with 40 and 80 MPa normal stresses and no applied shear.

    Chapters
    • 1:04:12Plane stress transformation equations (chapter 2, session 1)
  4. 1:32:0850 min · 2 chapters

    Principal stresses, maximum shear stress and Mohr's circle

    Derives the principal stresses and maximum in-plane shear stress by differentiating the transformation equation (principal planes 90 degrees apart, shear planes 45 degrees from them) and solves a numerical example. Then draws Mohr's circle (centre at the average stress, radius by Pythagoras), absolute maximum shear stress from three circles, and a thin-walled pressure vessel.

    Chapters
    • 1:32:08Principal stresses and maximum in-plane shear stress (chapter 2, session 2)
    • 1:53:41Mohr's circle and absolute maximum shear stress (chapter 2, session 3)
  5. 2:22:1839 min · 2 chapters

    Beams, supports, loads, shear force and bending moment diagrams

    Covers the parts of a beam, roller, pinned and fixed supports, point, uniformly distributed and uniformly varying loads, and cantilever, fixed and simply supported beams. Defines shear force and bending moment with a sign convention, then draws the SFD and BMD for a simply supported beam and a cantilever carrying a 10 kN point load and a 1 kN/m distributed load.

    Chapters
    • 2:22:18Beam types, supports and loads (chapter 3, session 1)
    • 2:39:16Shear force and bending moment diagrams (chapter 3, session 2)
  6. 3:01:1842 min · 2 chapters

    Bending, deflection and torsion of circular shafts

    Shows how point, uniformly distributed and uniformly varying loads shape the SFD and BMD, then derives the bending equation (M/I = E/R = f/y), section modulus, flexural rigidity and deflection by double integration. Torsion follows: shear strain varying with radius, the torsion formula, polar moment of inertia for solid and hollow shafts, and a solid versus hollow shaft example.

    Chapters
    • 3:01:18Load shapes in SFD and BMD, bending equation and deflection (chapter 3, session 3)
    • 3:22:02Torsion of circular shafts and the torsion formula (chapter 3, session 4)
  7. 3:43:3521 min · 1 chapter

    Failure by yielding and fracture, ductile and brittle materials

    Explains that what counts as failure depends on the application, and splits common failure into excessive elastic deformation (including buckling and resonance), yielding failure (including creep at high temperature) and fracture. Compares ductile and brittle stress-strain curves for mild steel, cast iron and concrete, including reinforced concrete.

    Chapters
    • 3:43:35Failure by yielding and fracture, ductile and brittle materials (chapter 4, session 1)
  8. 4:04:4143 min · 2 chapters

    Theories of failure and a worked shaft example

    Starts with the strain-based theories: maximum principal strain (Saint-Venant) and total strain energy (Beltrami). Then the Tresca and Huber-Hencky-von Mises theories for ductile materials, the Rankine and Mohr criteria for brittle ones, and a solid steel shaft under axial load and torsion checked against both ductile theories.

    Chapters
    • 4:04:41Strain-based failure theories (chapter 4, session 2)
    • 4:18:46Yield and fracture criteria with a worked shaft example (chapter 4, session 3)

Is the Strength of Materials: Engineering Basics course really free?

Yes. All 4 h 48 min of it is free on Skill-Lync's YouTube channel, with no payment. To watch it on this page with the chapter guide, leave your name and phone number once; you can also watch it directly on YouTube. It was published on 8 Nov 2024 and had 74,271 views as of 18 Nov 2026. This page adds the chapter guide, a study plan and what to learn next.

How long does the Strength of Materials: Engineering Basics course take to finish?

The video runs 4 h 48 min across 14 chapters. At one hour a day that is about 5 days; plan roughly twice that if you practise each exercise as you go. The longest section is "Principal stresses, maximum shear stress and Mohr's circle" (50 min), so give it its own days.

Does the free Strength of materials course come with a certificate?

The video description has a "claim your certificate" link, which now opens this page. To ask about a certificate for this course, leave your name and phone number in the form below and a Skill-Lync counsellor will call you back. The paid Skill-Lync courses linked here include a certificate along with mentor-reviewed projects.

What should I learn after this course?

The next step is Strength of Materials: free interactive book, then Post Graduate Program in CAE (₹2,75,000). The free course teaches the concepts; the paid Skill-Lync courses add graded projects, mentor feedback and, in the PG programs, placement support.

Do I need any software to follow the strength of materials course?

No. The course is a lecture with slides, whiteboard derivations and hand calculations, and no simulation software is used. The one tool shown is Excel, which the lecturer uses in chapter 1 to plot load against elongation and read off stiffness. A calculator is enough for the worked examples.

What maths do I need for the strength of materials course?

The video does not list prerequisites. Its derivations use trigonometry (the plane stress transformation and Mohr's circle), and differentiation and integration (principal stresses, beam deflection and torsion). Basic statics, such as free body diagrams and equilibrium of forces and moments, is used throughout the beam and shaft examples.

What does the strength of materials course cover on beams and shafts?

Chapter 3 covers beam supports and loads, shear force and bending moment diagrams for a simply supported beam and a cantilever, the bending equation, section modulus and deflection by double integration. It ends with torsion of circular shafts, the torsion formula, and a solid versus hollow shaft example.

Last updated 18 Nov 2026 · Course length, chapters, views and dates from the YouTube video on 18 Nov 2026 · Grow by Skill-Lync: free lessons from every course

Finished the course?

Ask about the certificate or your next course.

Leave your name and phone number. A Skill-Lync counsellor calls you back within one working day about the certificate for Strength of Materials: Engineering Basics and the course that fits where you want to work.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Free full course · Skill-Lync

Start watching

Free, no payment. Leave your name and phone once and the whole Strength of Materials: Engineering Basics course plays here, with every free lesson on Grow. A Skill-Lync counsellor may call you about the certificate or your next course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.