Full course · free on YouTube · 49 min

Meshing using HyperMesh webinar: free, 49 minutes

This is a February 2023 recording of a live Skill-Lync webinar, 49 minutes long, presented with slides. It explains what HyperMesh is, why we mesh, how to choose between 1D, 2D and 3D elements and element size, then the quality checks for 2D and 3D meshes. It introduces concepts and does not show a live HyperMesh session.

23 chapters · published 6 Feb 2023 · 2,150 views as of 21 Nov 2026 · by Skill-Lync

Free. We ask for your name and phone once before it plays here · or watch on YouTube ↗

Who is this course for?

Mechanical and CAE students and early-career FEA users who want an overview of how to choose element types and check mesh quality before using HyperMesh.

What will you learn?

  • Place HyperMesh as a pre-processor in the FEA steps of pre-processing, solving and post-processing
  • Explain why a component is meshed into a finite number of nodes and elements
  • Choose between 1D, 2D and 3D elements using geometry, type of analysis and project time
  • Use the speaker's tips for holes, fillets, mesh transitions and 2D and 3D meshes to avoid
  • Read the typical 2D limits quoted for warp (10°), aspect ratio (5) and skew (45°)
  • List checks to run on a 2D mesh before handing it over, and what tetra collapse means in 3D

What does each part of the course cover?

8 sections, in watching order. Click a timestamp to jump the player there. The video description has no chapter list, so these chapters and timestamps were written from the video itself.

  1. 0:007 min · 3 chapters

    What HyperMesh is and why it is used

    After the agenda, the speaker defines HyperMesh as a pre-processor from Altair within FEA and CAE. It then covers the claimed benefits: control over mesh quality, batch meshing and Tcl/Tk scripting for repeated design iterations, a place in PLM, and support for several solvers such as Abaqus.

    Chapters
    • 0:00Welcome and agenda for the HyperMesh meshing webinar
    • 0:51What HyperMesh is and where it fits in CAE and FEA
    • 3:46Benefits: control, automation, TCL/TK scripting and solver support
  2. 7:275 min · 2 chapters

    Pre-processing steps and why we mesh

    Lists the pre-processing steps with a crash-test example: defeature the model, pick element types and properties, assign material, apply constraints and initial velocity, and choose the analysis type. Then explains meshing as replacing infinite degrees of freedom with a finite number of nodes and elements.

    Chapters
    • 7:27Pre-processing steps, with a car crash example
    • 10:34Why we mesh: from infinite to finite degrees of freedom
  3. 12:089 min · 4 chapters

    Choosing element types

    Covers mass, spring, damper, rigid and constraint elements with a stool-and-weight example. Then explains 1D, 2D (mid-surface plus thickness) and 3D elements by geometry, and the speaker's preferences by type of analysis: quad and hex for structural and fatigue work, shells for large dynamic models.

    Chapters
    • 12:08Element families: mass, spring, damper, rigid and constraint elements
    • 16:09Choosing an element type by geometry, and 1D elements
    • 17:492D shell elements and mid-surface meshing
    • 20:013D elements, and choosing elements by type of analysis
  4. 21:367 min · 3 chapters

    Project time, element length and mesh sensitivity

    Argues that time allotted to a project drives how structured the mesh can be, and lists compromises. A cantilever beam is meshed with 1D, 2D and 3D elements to compare node counts. Then covers choosing element size from past experience and running a mesh sensitivity study.

    Chapters
    • 21:36Project time and the compromises it forces
    • 23:30Can 1D, 2D and 3D solve the same problem? A cantilever beam example
    • 25:41Deciding element length and the mesh sensitivity study
  5. 28:355 min · 2 chapters

    Geometry checks, symmetry and critical areas

    Before meshing, check the geometry for free edges, duplicate surfaces, small fillets and holes, and check interference and symmetry (quarter and sector models). Then gives element counts around holes and fillets, a plastic bucket meshed with shell, beam and connector elements, and where mesh transitions should not go.

    Chapters
    • 28:35Before meshing: geometry checks, interference and symmetry
    • 31:36Mixed element example (plastic bucket) and meshing critical areas
  6. 33:485 min · 3 chapters

    1D and 2D element types and 2D meshing tips

    Lists 1D element types (rod, bar, beam, pipe, axisymmetric shell) and the 2D quad and tria shapes in linear and higher order. Shows how not to mesh in 2D: back-to-back trias, sharp elements at bolt holes, ignored feature lines, and why explicit crash analysis prefers constant element size.

    Chapters
    • 33:481D element types: rod, bar, beam, pipe and axisymmetric shell
    • 35:022D element shapes: quad and tria, linear and higher order
    • 36:05How not to mesh in 2D, and element size for explicit crash analysis
  7. 38:546 min · 3 chapters

    2D quality criteria and checks

    Introduces ideal quad and tria shapes and the Jacobian as the mapping from real to ideal element. Gives the speaker's typical limits for warp angle, aspect ratio, skew and included angles, then checks before delivery: free edges, duplicates, normals, renumbering, tria share and mass.

    Chapters
    • 38:54Quality checks for 2D mesh: ideal shapes and the Jacobian
    • 40:43Typical 2D limits: warp, aspect ratio, skew and included angles
    • 42:51Checks to run on a 2D mesh before delivery
  8. 45:044 min · 3 chapters

    3D elements and 3D mesh quality

    Shows tetra, penta, hexa and pyramid elements, linear and higher order, with tips on curvature and element count through the thickness. Explains tetra collapse and gives key points: quadratic tetra for structural analysis, and linear elements acceptable in thermal analysis.

    Chapters
    • 45:043D elements: tetra, penta, hexa and pyramid
    • 45:58How not to mesh in 3D: curvature and elements through thickness
    • 46:453D quality checks, tetra collapse and closing key points

Is the Meshing using HyperMesh course really free?

Yes. All 49 min of it is free on Skill-Lync's YouTube channel, with no payment. To watch it on this page with the chapter guide, leave your name and phone number once; you can also watch it directly on YouTube. It was published on 6 Feb 2023 and had 2,150 views as of 21 Nov 2026. This page adds the chapter guide, a study plan and what to learn next.

How long does the Meshing using HyperMesh course take to finish?

The video runs 49 min across 23 chapters. That fits in one sitting of under an hour; plan roughly twice that if you practise each exercise as you go. The longest section is "Choosing element types" (9 min), so give it your full attention.

Does the free HyperMesh course come with a certificate?

The video description has a "claim your certificate" link, which now opens this page. To ask about a certificate for this course, leave your name and phone number in the form below and a Skill-Lync counsellor will call you back. The paid Skill-Lync courses linked here include a certificate along with mentor-reviewed projects.

What should I learn after this course?

The next step is Crashworthiness Analysis using HyperMesh and Radioss (free lessons), then HyperMesh for FEA Plastic and Sheet Metal Applications (₹40,000), then Post Graduate Program in CAE (₹2,75,000). The free course teaches the concepts; the paid Skill-Lync courses add graded projects, mentor feedback and, in the PG programs, placement support.

Is there a live HyperMesh demo in this webinar?

No. The speaker works through slides covering what HyperMesh is, why meshing is done, element types and mesh quality criteria, with example images of meshes. The description calls it a preview of the software, so treat it as a concepts session before you open HyperMesh yourself. No prerequisites are stated in the video.

What 2D mesh quality limits does the speaker give?

For 2D shell elements the speaker quotes a warp angle below 10°, aspect ratio below 5, skew not above 45°, and included angles of 45° to 135° for quads and 20° to 120° for trias. These are typical limits quoted in this webinar, so check your company or solver guidelines before using them as rules.

When does the speaker use 1D, 2D or 3D elements?

The speaker uses 1D elements when one dimension is much larger than the other two, such as a long shaft or beam. For 2D shells the thickness should be consistent with a width to thickness ratio above 20. 3D elements suit solid parts such as crankshafts, where all three dimensions are comparable and through-section stress matters.

Last updated 21 Nov 2026 · Course length, chapters, views and dates from the YouTube video on 21 Nov 2026 · Grow by Skill-Lync: free lessons from every course

Finished the course?

Ask about the certificate or your next course.

Leave your name and phone number. A Skill-Lync counsellor calls you back within one working day about the certificate for Meshing using HyperMesh and the course that fits where you want to work.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Free full course · Skill-Lync

Start watching

Free, no payment. Leave your name and phone once and the whole Meshing using HyperMesh course plays here, with every free lesson on Grow. A Skill-Lync counsellor may call you about the certificate or your next course.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.